We currently transition the port to "Virtual mode" upon the creation of
its first VLAN upper, as we need to classify incoming packets to a FID
using {Port, VID} and not only the VID.

However, it's more appropriate to transition the port to this mode when
the {Port, VID} are actually mapped to a FID. Either during the
enslavement of the VLAN upper to a VLAN-unaware bridge or the
configuration of a router port.

Do this change now in preparation for the introduction of the FID core,
where this operation will be encapsulated.

To prevent regressions, this patch also explicitly configures an OVS
slave to "Virtual mode". Otherwise, a packet that didn't hit an ACL rule
could be classified to an existing FID based on a global VID-to-FID
mapping, thus not incurring a FID mis-classification, which would
otherwise trap the packet to the CPU to be processed by the OVS daemon.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of falling back to 00:00:00:00:00:00 generate a random address
if none is provided via platform data or from the device's register
space.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

lio_enable_irq (called by napi poll) is reporting to Octeon an inaccurate
count of processed rx packets causing Octeon to eventually stop forwarding
packets to the host.  Fix it by using this formula for an accurate count:

    processed rx packets = droq->pkt_count - droq->pkts_pending

Also increase SOFT_COMMAND_BUFFER_SIZE to match what the firmware expects.
Signed-off-by: NPrasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a rare pci_driver.probe failure of the VF driver that's caused by
PF/VF handshake going out of sync.  The culprit is octeon_mbox_write() who
ignores an ack timeout condition; it just keeps unconditionally writing all
elements of mbox_cmd->data[] even when the other side is not ready for
them.  Fix it by making each write of mbox_cmd->data[i] conditional to
having previously received an ack.

Also fix the octeon_mbox_state enum such that each state gets a unique
value.  Also add ULL suffix to numeric literals in macro definitions.
Signed-off-by: NPrasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for configuring port split with devlink.  Add devlink
callbacks to validate requested config and call NSP helpers.
Getting the right nfp_port structure can be done with simple iteration.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For port splitting we will need to know the total number of lanes
in a port.  Calculate that based on eth_table information.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend nfp_port to contain devlink_port structures.  Register the
ports to allow users inspecting device ports.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We will soon have to invoke more clean up for vNICs.
Move the cleanup callbacks into a helper.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add initial devlink support.  This patch simply switches allocation
of per-adapter structure to devlink's priv and register devlink
with empty ops table.  See following patches for implementation
of particular ops.

We should now clear the app pointer on exit, this is how devlink
callbacks will know app is not initialized.
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move mutex init to main file close to structure allocation.
This will allow mutex to be taken before net code runs (e.g.
from devlink callbacks).  While at it remember to destroy
the mutex.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In new firmware versions, when configuring a {Port, VID} as a router
interface, the driver is responsible for enabling the STP filter and
disabling learning.  Otherwise, packets are discarded.

This change doesn't break existing firmware versions, but is required
for newer firmware versions.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the spectrum module check the current device firmware version, and if
it is below the supported version, use the libfirmware API to request a
firmware file with the supported firmware version and flash it to the
device using the mlxfw module.

The firmware file names are expected to be of Mellanox Firmware Archive
version 2 (MFA2) format and their name are expected to be in the following
pattern: "mlxsw_spectrum-<major>.<minor>.<sub-minor>.mfa2".
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This struct was previously an anonymous struct defined inside the
mlxsw_bus_info struct. Extract it to a struct named mlxsw_fw_rev, as it
will be needed later by the spectrum driver.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mlxfw module defines several needed callbacks in order to flash the
device's firmware. As the mlxfw module is shared between several different
drivers, those callbacks are the glue functionality that is responsible
for hardware interaction. Add those callbacks using the MCQI, MCC, MCDA
registers.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MCDA register allows reading and writing a firmware component.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MCC register allows controlling and querying the firmware flash state
machine (FSM).
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MCQI register queries information about firmware components. It will
be needed by the mlxfw module to query various options about the
components, such as their max size, alignment and max write size.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mlxfw module is in charge of common logic needed to flash Mellanox
devices firmware, which consists of:
 - Parse the Mellanox Firmware Archive version 2 (MFA2) format, which is
   the format used to store the Mellanox firmware. The MFA2 format file can
   hold firmware for many different silicon variants, differentiated by a
   unique ID called PSID. In addition, the MFA2 file data section is
   compressed using xz compression to save both file-system space and
   memory at extraction time.
 - Implement the firmware flash state machine logic, which is a common
   logic for Mellanox products needed to flash the firmware to the device.

As the module is shared between different Mellanox products, it defines a
set of callbacks to be implemented by the specific driver for hardware
interaction.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSuresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On certain platforms BE3 chips may indicate spurious UEs (unrecoverable
error). Because of the UE detection logic was disabled in the driver
for BE3 chips. Because of this, even in cases of a real UE,
a failover will not occur. This patch re-enables UE detection on BE3
and if a UE is detected, reads the POST register. If the POST register,
reports either a FAT_LOG_STATE or a ARMFW_UE, then it means that a valid
UE occurred in the chip.
Signed-off-by: NSuresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current stmmac_adjust_link() part which handle speed have
some if (has_platform) code and my dwmac-sun8i will add more of them.

So we need to handle better speed selection.
Moreover the struct link member speed and port are hard to guess their
purpose. And their unique usage are to be combined for writing speed.

So this patch replace speed/port by simpler
speed10/speed100/speed1000/speed_mask variables.

In dwmac4_core_init and dwmac1000_core_init, port/speed value was used
directly without using the struct link. This patch convert also their
usage to speedxxx.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch convert old_link from int to bool since it store only 1 or 0
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch convert new_state from int to bool since it store only 1 or 0
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The functions jme_restart_tx_engine(), jme_pause_rx() and
jme_resume_rx() are not used. Removing them fixes the following warnings
when building with clang:

drivers/net/ethernet/jme.c:694:1: error: unused function
    'jme_restart_tx_engine' [-Werror,-Wunused-function]

drivers/net/ethernet/jme.c:2393:20: error: unused function
    'jme_pause_rx' [-Werror,-Wunused-function]

drivers/net/ethernet/jme.c:2406:20: error: unused function
    'jme_resume_rx' [-Werror,-Wunused-function]
Signed-off-by: NMatthias Kaehlcke <mka@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow to offload rules that contain tcp flags within the mask.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add acl block called "ipv4" which contains tcp flags.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define new element for tcp flags and place it into scratch area.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current API between qed and protocol modules allows passing an
additional private string - but it doesn't get utilized by qed
anywhere.

Clarify the API by removing it and renaming it 'set_name'.

CC: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace meaningless logged print ('Ending successfully qede probe')
with a single-liner containing interesting information about probed
device.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass additional information about package installed on persistent memory
so that protocol drivers would be able to log it.
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we're closing the parser searching for RDMA when stoping the
fastpath, we need to re-enable it when starting the fastpath once again.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Today, driver has a synchronization point while closing
the device which synchronizes its slowpath interrupt line.
However, that's insufficient as that ISR would schedule the
slowpath-tasklet - so even after ISR is over it's possible the
handling of the interrupt has not completed.

By doing a disable/enable on the taskelt we guarantee that all
HW events that should no longer be genereated from that point
onward in the flow are truly behind us.
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A0 never went public, so no need to protect against it.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The parameter reflects the number of physical ports connected to a single
engine, not all.
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case nvram layout of board is incorrect, board may exhibit peculiar
oddities. Log such a rare event.
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flows configuring tunnel ports in HW use the main_ptt which should
be reserved for core-functionality.
Signed-off-by: NManish Chopra <Manish.Chopra@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Solves the following warning in qede -
 - Several cases of missing cpu_to_le16() conversions
 - Adds 'static' to one function declaration
 - Removes dcbnl operation that's currently getting populated twice
Signed-off-by: NManish Chopra <Manish.Chopra@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of busy poll, napi_complete_done returns false and does not
dequeue napi. In this case do not unmask the intr. We are guaranteed
napi is called again. This reduces unnecessary iowrites.
Signed-off-by: NGovindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>