The mxs.h does not exit in the mx6q.
So rewrite the __mxs_clrl()/__mxs_setl() and remove the mxs.h.
Signed-off-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The last DMA command of ECC read page is used to disable the BCH module.
But the original code missed to set the pio[2] which is used to set the
GPMI_HW_GPMI_ECCCTRL register. fix it now.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

[1] Background :
    The GPMI does ECC read page operation with a DMA chain consist of three DMA
    Command Structures. The middle one of the chain is used to enable the BCH,
    and read out the NAND page.

    The WAIT4END(wait for command end) is a comunication signal between
    the GPMI and MXS-DMA.

[2] The current DMA code sets the WAIT4END bit at the last one, such as:

    +-----+               +-----+                      +-----+
    | cmd | ------------> | cmd | ------------------>  | cmd |
    +-----+               +-----+                      +-----+
                                                          ^
                                                          |
                                                          |
                                                     set WAIT4END here

    This chain works fine in the mx23/mx28.

[3] But in the new GPMI version (used in MX50/MX60), the WAIT4END bit should
    be set not only at the last DMA Command Structure,
    but also at the middle one, such as:

    +-----+               +-----+                      +-----+
    | cmd | ------------> | cmd | ------------------>  | cmd |
    +-----+               +-----+                      +-----+
                             ^                            ^
                             |                            |
                             |                            |
                        set WAIT4END here too        set WAIT4END here

    If we do not set WAIT4END, the BCH maybe stalls in "ECC reading page" state.
    In the next ECC write page operation, a DMA-timeout occurs.
    This has been catched in the MX6Q board.

[4] In order to fix the bug, rewrite the last parameter of mxs_dma_prep_slave_sg(),
    and use the dma_ctrl_flags:
    ---------------------------------------------------------
      DMA_PREP_INTERRUPT : append a new DMA Command Structrue.
      DMA_CTRL_ACK       : set the WAIT4END bit for this DMA Command Structure.
    ---------------------------------------------------------

[5] changes to the relative drivers:
    <1> For mxs-mmc driver, just use the new flags, do not change any logic.
    <2> For gpmi-nand driver, and use the new flags to set the DMA
        chain, especially for ecc read page.
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Acked-by: NVinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

In MX28, if we do not reset the BCH module. The BCH module may
becomes unstable when the board reboots for several thousands times.
This bug has been catched in customer's production.

The patch adds some comments (some from Wolfram Sang), and fixes it now.

Also change gpmi_reset_block() to static.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org [3.1+]

The patch converts gpmi nand driver to clk_prepare/clk_unprepare by
using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Huang Shijie <b32955@freescale.com>
Cc: Artem Bityutskiy <artem.bityutskiy@intel.com>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>

This patch fixes usage of dma direction to adopt dma_transfer_direction.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

bch-regs.h : registers file for BCH module
gpmi-regs.h: registers file for GPMI module
gpmi-lib.c: helper functions library.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Tested-by: NKoen Beel <koen.beel@barco.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@intel.com>