- 06 8月, 2010 9 次提交
-
-
由 Francisco Jerez 提交于
sil164 and friends are the most common, usually they just need to be poked once because a fixed configuration is enough for any modes and clocks, so they worked without this patch if the BIOS had done a good job on POST. Display couldn't survive a suspend/resume cycle though. Unfortunately, BIOS scripts are useless here. Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Not very nice, but I don't think there's a simpler workaround. Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Leaving the IRQ unack'ed while switching contexts makes the switch fail randomly on some nv1x. Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Dan Carpenter 提交于
nouveau_load() just returned directly if there was an error instead of releasing resources. Signed-off-by: NDan Carpenter <error27@gmail.com> Reviewed-by: NMarcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Previously nouveau_mem_reset_agp() was only disabling AGP fast writes when coming back from suspend. However, the "locked out of the card because of FW" problem can also be reproduced on init if you unload/reload nouveau.ko several times. This patch makes the AGP code reset FW on init. Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Ben Skeggs 提交于
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Ben Skeggs 提交于
This makes it easier to see how this is working, and lets us transfer the EDID in blocks of 16 bytes. The primary reason for this change is because debug logs are rather hard to read with the hundreds of single-byte auxch transactions that occur. Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
- 05 8月, 2010 1 次提交
-
-
由 Chris Wilson 提交于
This is required should we ever attempt to use an io-mapping where KM_USER0 is verboten, such as inside an IRQ context. Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Eric Anholt <eric@anholt.net> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
- 04 8月, 2010 1 次提交
-
-
由 Dave Airlie 提交于
I wrote this for the prime sharing work, but I also noticed other external non-upstream drivers from a large company carrying a similiar patch, so I may as well ship it in master. Signed-off-by: NDave Airlie <airlied@redhat.com>
-
- 02 8月, 2010 2 次提交
-
-
由 Francisco Jerez 提交于
sil164 transmitters are used for DVI outputs on Intel/nvidia and ATI setups. So far only nouveau can use this driver. Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Tested-by: NPatrice Mandin <patmandin@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Kulikov Vasiliy 提交于
set_current_state() is called only once before the first iteration. After return from schedule_timeout() current state is TASK_RUNNING. If we are going to wait again, set_current_state() must be called. Signed-off-by: NKulikov Vasiliy <segooon@gmail.com> Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
- 26 7月, 2010 26 次提交
-
-
由 Ben Skeggs 提交于
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Ben Skeggs 提交于
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Ben Skeggs 提交于
Reported-by: NMarcin Kościelnicki <koriakin@0x04.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
I was hoping we could detect I2C devices at a given address without actually writing data into them, but apparently some DDC slaves get confused with 0-bytes transactions. Put the good old test back. Reported-by: NBen Skeggs <bskeggs@redhat.com> Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
BIOS scripts usually make an attempt to reset the AGP controller, however on some nv4x cards doing it properly involves switching FW off and on: if we do that without updating the AGP bridge settings accordingly (e.g. with the corresponding calls to agp_enable()) we will be locking ourselves out of the card MMIO space. Do it from nouveau_mem_reset_agp() before the init scripts are executed. Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Fixes the randomly flashing vertical lines seen on some nv3x after a cold-boot. Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Ben Skeggs 提交于
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Ben Skeggs 提交于
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Ben Skeggs 提交于
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Ben Skeggs 提交于
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Fixes suspend+multihead on some boards that also use BIOS scripts for modesetting. Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Locking only makes sense in the VBIOS parsing code as it's executed before CRTC init. Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Clean up and move the external TV encoder detection code to nouveau_i2c.c, it's also going to be useful for external TMDS and DDC detection. Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Init-compute-mem was the last piece missing for nv0x-nv3x card cold-booting. This implementation is somewhat lacking but it's been reported to work on most chipsets it was tested in. Let me know if it breaks suspend to RAM for you. Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Tested-by: NPatrice Mandin <patmandin@gmail.com> Tested-by: NBen Skeggs <bskeggs@redhat.com> Tested-by: NXavier Chantry <chantry.xavier@gmail.com> Tested-by: NMarcin Kościelnicki <koriakin@0x04.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Also collect all the PFB registers in a single place and remove some duplicated definitions. Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
Rescaling interlaced modes isn't going to work correctly, and even if it did, come on, interlaced flat panels? are you pulling my leg? Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Francisco Jerez 提交于
It doesn't like variable length arrays. Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Ben Skeggs 提交于
A previous commit started additionally using the SOR link when trying to match the correct output script. However, we never fill in this field for LVDS so we can never match a script at all. Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Ben Skeggs 提交于
Based on a patch from Matthew Garrett. Signed-off-by: NBen Skeggs <bskeggs@redhat.com> Acked-by: NMatthew Garrett <mjg@redhat.com>
-
由 Ben Skeggs 提交于
There's a report of this quirk breaking modesetting on at least one board. After discussion with Francisco Jerez, we've decided to remove it: <darktama> it's not worth limiting the quirk to just where we know it can work? i'm happy either way really :) <curro> hmm, don't think so, most if not all DCB15 cards have just one DAC <curro> and with that quirk there's no way to tell if the load comes from the VGA or DVI port Signed-off-by: NBen Skeggs <bskeggs@redhat.com> Acked-by: NFrancisco Jerez <currojerez@riseup.net>
-
由 Ben Skeggs 提交于
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
- 21 7月, 2010 1 次提交
-
-
由 Francisco Jerez 提交于
this fixes a regression since the fbcon rework. Signed-off-by: NFrancisco Jerez <currojerez@riseup.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-