Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 21 11月, 2012 3 次提交
  3. 15 11月, 2012 1 次提交
  5. 11 11月, 2012 1 次提交
  7. 26 10月, 2012 1 次提交
  9. 25 10月, 2012 2 次提交
  11. 18 10月, 2012 1 次提交
  13. 08 10月, 2012 3 次提交
  15. 07 10月, 2012 2 次提交
  17. 06 10月, 2012 2 次提交
  19. 03 10月, 2012 3 次提交
  21. 02 10月, 2012 4 次提交
  23. 01 10月, 2012 2 次提交
    • T
      dt: Document general interrupt controller bindings · acc20979
      由 Thierry Reding 提交于 
      In order to use a device as interrupt controller, it needs to be marked
with the DT interrupt-controller property. This commit adds rudimentary
documentation about the required standard properties and describes the
most commonly used interrupt specifiers.

Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
      acc20979
    • S
      pinctrl: add bcm2835 driver · e1b2dc70
      由 Simon Arlott 提交于 
      The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.

Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.

Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
  datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
  implemented are driven by the board, not the GPIO HW block, so don't
  really make sense of a HW block binding, were in general incomplete
  (since they could only know about the few pins hard-coded into the
  Raspberry Pi B board design and not the uncommitted GPIOS), and are
  better represented simply by not writing incorrect data into pin
  configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
  glitches; defer this to gpio_set_direction(). Consequently, removed
  empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
  IRQ handler, thus fixing an issue where the code was indexing into
  enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
  spin_lock_irqsave() and so guarantees it doesn't run concurrently
  with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
  bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
  decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
  directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
  core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
  descriptive.
* Simplified remove(); removed call to non-existent
  pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
  base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NChris Boot <bootc@bootc.net>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      e1b2dc70
  25. 29 9月, 2012 2 次提交
  27. 28 9月, 2012 1 次提交
  29. 27 9月, 2012 2 次提交
  31. 25 9月, 2012 5 次提交
  33. 22 9月, 2012 5 次提交