The debug message is only relevant on CPT/PPT PCH ports, so move
it into the correct if clause.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NYuly Novikov <ynovikov@chromium.org>
[Jani: ripped this change separate from the scaling mode change support]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

LVDS allowed changing panel fitting scaling mode, while eDP didn't. Copied
relevant code from LVDS to eDP.
Signed-off-by: NYuly Novikov <ynovikov@chromium.org>
[Jani: use fitting mode in intel_panel, remove default mode change]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

At some point the DPCD size was increased, but the debug print not. While
at it, switch to using hex dump.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's an important step :)
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The cdclk frequency is not always the same, so the value here should
be adjusted to match it.

Version 2: call intel_ddi_get_cdclk_freq instead of reading
CDCLK_FREQ, because the register is just for earlier HW steppings.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Same thing as the previous commits. Not renaming this one since it
exists since way before Haswell.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

That thing has grown way too big already.

Also move around a comment to the right spot.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise dp aux won't work on some hsw platforms, since they use a
different rawclk than the 125MHz clock used thus far.

To absolutely not change anything, round up: That way we get the old
63 divider for the default 125MHz clock.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need this when the bios forgets even to set that bit up. Most seem
to do that, even when they don't set up anything else in the panel
power sequencer.

Note that on IBX the rawclk is variable according to Bspec, but
everyone is using 125MHz. The rawclk is fixed to 125MHz on CPT, but
luckily we still have the same register available. On hsw, different
variants have different clocks, hence we need to check the register.

Since other pieces are driven by the rawclock, too, keep the little
helper in a central place.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Like we already do for the LVDS panels. This seems to help greatly
in setting up the backlight, since the BIOS might refuse to cooperate.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>

v2: Move the backlight_off call from panel_off to edp_backlight_off,
noticed by Paulo Zanoni.
Reviewed-by: NPaulo Zanoni <przanoni@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

3 changes:
- If a given value is unset, use the maximal limits from the eDP spec.
- Write back the new values, since otherwise the panel power sequencing
  hw will not dtrt.
- Revert the early bail-out in case the register values are unset.

The last change reverts

commit bfa3384a
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Tue Apr 10 11:58:04 2012 -0700

    drm/i915: check PPS regs for sanity when using eDP

v2:
- Unlock the PP regs as the very first thing. This is a required w/a
  for cpu eDP on port A, and generally a good idea.
- Fixup the panel power control port selection bits.

v3: Paulo Zanoni noticed that I've fumbled the computation of the spec
limit values. Fix them up. We've also noticed that the t8/t9 values in
the vbt/bios-programmed pp are much larger than any limits. My guess
is that this is to conceal any backlight enable/disable delays. So by
using the much shorter limits from the spec, which only concerns the
sink, we risk that we might display before the backlight is fully on,
or disable the output while the backlight still has afterglow. I've
figured I don't care too much, since this will only happen when both
the pp regs are not programmed, and the vbt tables don't contain
anything useful.

v4: Don't set the port selection bits on hsw/LPT, they don't exist any
more.

v5: Fixup spelling issues in comments, as noticed by Jesse Barnes.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... like the comment says. No idea whether this has any effect, but
I guess it's better to not lie to the display by acking a test request
and never following through with it. This goes back to the commit that
originally introduced this code:

commit a60f0e38
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Thu Oct 20 15:09:17 2011 -0700

    drm/i915: add DP test request handling
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Meh'ed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Only really required for dp 1.2. I've hoped this would help with some
link training woes I'm fighting, but alas those are only dp 1.1
devices.

Also move a comment that went misplaced in the recent refactorings to
the right spot again.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This requires a few changes since that dpcd value is above the
range currently cached by radeon. I've check the dp specs, and
above 0xf there's a big gap and nothing that looks like we should
cache it while a given device is plugged in. It's also the same value
that i915.ko uses.

Hence extend the various dpcd arrays in the radeon driver, use
proper symbolic constants where applicable (one place overallocated
the dpcd array to 25 bytes). Then also drop the rd_interval cache -
radeon_dp_link_train_init re-reads the dpcd block, so the values we'll
consume in train_cr and train_ce will always be fresh.

To avoid needless diff-churn, #define the old size of dpcd as the new
one and keep it around.

v2: Alex Deucher noticed one place where I've forgotten to replace 8
with DP_RECEIVER_CAP_SIZE.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Safe for the minor difference that the intel versions get an offset
into the link_status as an argument, both are the same again.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

radeon and intel use the exact same definition.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NDave Airlie <airlied@gmail.com>

v2: Kill 2 more helpers in intel_dp.c that I've missed.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

radeon and intel use the exact same definition.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move the cached EDID from intel_dp and intel_lvds_connector to
intel_connector. Unify cached EDID handling for LVDS and eDP, in
preparation for adding more generic EDID caching later.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Pave the way for sharing some logic between eDP and LVDS.

Based on earlier work by Chris Wilson <chris@chris-wilson.co.uk>

CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Create a generic struct intel_panel for sharing a data structure and code
between eDP and LVDS panels. Add the new struct to intel_connector so that
later on we can have generic EDID and mode reading functions with EDID
caching that transparently fallback to fixed mode when EDID is not
available.

Add intel_panel as a dummy first, and move data (such as the mentioned
fixed mode) to it in later patches.

Based on earlier work by Chris Wilson <chris@chris-wilson.co.uk>

CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Fixup tiny conflict in intel_dp_destroy.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since we do EDID caching in intel_dp_init, we can do the fixed mode
initialization there too. This should not change the functionality apart
from initializing fixed mode earlier. Particularly retain the behaviour of
only falling back to VBT if EDID is not available to not regress

commit 47f0eb22
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Sep 19 14:33:26 2011 -0700

    drm/i915: Only use VBT panel mode on eDP if no EDID is found
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Get rid of saved int_lvds_connector and int_edp_connector in
drm_i915_private.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is the final remaining piece of Haswell DP enablement. After this
patch, just calling intel_dp_init on any port will make DP work. We
still do not do this because we're currently initializing HDMI on all
the ports, so if we replace intel_hdmi_init with intel_dp_init, we
will break HDMI, and we can't call both because they share the same
registers.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Previous patch "drm/i915: add basic Haswell DP link train bits"
implemented the basic structure to set the voltage levels and training
patterns. This patch adds the higher-level bits that are part of the
mode set sequence and hot plug.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have to write the correct values inside intel_dp_set_m_n and then
prevent these values from being overwritten later.

V2: Unconfuse double negation.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The old rule that the AUX registers are just an offset (+4 and +10)
from output_reg is not true anymore, since output_reg in on the CPU
and some AUX regs are on the PCH.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: use the existing #defines as spotted by Damien Lespiau.]
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Much simpler and looks more like the M/N code inside intel_display.c.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Previously, the DP register was used for everything. On Haswell, it
was split into DDI_BUF_CTL (which is the new intel_dp->DP register)
and DP_TP_CTL.

The logic behind this patch is based on a patch written by Shobhit
Kumar, but the way the code was written is very different.

Credits-to: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fixup the logic error spotted by Jani Nikula.]
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Backlight is initialized for eDP, but cleaned up only for eDP on DP-D
port. This leaves behind a dangling backlight interface on module unload on
machines that have eDP connected to something other than DP-D, and breaks
the backlight interface for subsequent module reloads. Fix the cleanup, and
thus module reload on affected machines.
Reported-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Tested-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In commit cdb0e95b
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Nov 1 20:00:06 2011 -0700

    drm/i915: Try harder during dp pattern 1 link training

extra passes were made to retry the same voltage and then retry a full
clock reset. However, as coverity pointed out, we never tried the full
clock reset as we broke out of the loop early.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NDave Airlie <airlied@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>

Remove redundant DRM UAPI header #inclusions from drivers/gpu/.

Remove redundant #inclusions of core DRM UAPI headers (drm.h, drm_mode.h and
drm_sarea.h).  They are now #included via drmP.h and drm_crtc.h via a preceding
patch.

Without this patch and the patch to make include the UAPI headers from the core
headers, after the UAPI split, the DRM C sources cannot find these UAPI headers
because the DRM code relies on specific -I flags to make #include "..."  work
on headers in include/drm/ - but that does not work after the UAPI split without
adding more -I flags.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NDave Airlie <airlied@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>

Signed-off-by: NAdam Jackson <ajax@redhat.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If there's no downstream device, DPCD success is good enough.  If
there's a hotplug-capable downstream device, count the number of
connected sinks in DP_SINK_STATUS and return success if it's non-zero.
Otherwise, probe DDC and report appropriately.

v2: Check DP_SINK_STATUS instead of something unrelated to sink status.
Tested-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>