Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 26 11月, 2010 1 次提交
  3. 16 11月, 2010 1 次提交
  5. 12 11月, 2010 1 次提交
  7. 27 10月, 2010 3 次提交
  9. 12 10月, 2010 1 次提交
  11. 10 8月, 2010 1 次提交
  13. 05 8月, 2010 1 次提交
    • K
      printk: fix delayed messages from CPU hotplug events · 034260d6
      由 Kevin Cernekee 提交于 
      When a secondary CPU is being brought up, it is not uncommon for
printk() to be invoked when cpu_online(smp_processor_id()) == 0.  The
case that I witnessed personally was on MIPS:

http://lkml.org/lkml/2010/5/30/4

If (can_use_console() == 0), printk() will spool its output to log_buf
and it will be visible in "dmesg", but that output will NOT be echoed to
the console until somebody calls release_console_sem() from a CPU that
is online.  Therefore, the boot time messages from the new CPU can get
stuck in "limbo" for a long time, and might suddenly appear on the
screen when a completely unrelated event (e.g. "eth0: link is down")
occurs.

This patch modifies the console code so that any pending messages are
automatically flushed out to the console whenever a CPU hotplug
operation completes successfully or aborts.

The issue was seen on 2.6.34.

Original patch by Kevin Cernekee with cleanups by akpm and additional fixes
by Santosh Shilimkar.  This patch superseeds
https://patchwork.linux-mips.org/patch/1357/.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
To: <mingo@elte.hu>
To: <akpm@linux-foundation.org>
To: <simon.kagstrom@netinsight.net>
To: <David.Woodhouse@intel.com>
To: <lethal@linux-sh.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: <linux-mips@linux-mips.org>
Reviewed-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1534/
LKML-Reference: <ede63b5a20af951c755736f035d1e787772d7c28@localhost>
LKML-Reference: <EAF47CD23C76F840A9E7FCE10091EFAB02C5DB6D1F@dbde02.ent.ti.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      034260d6
  15. 21 5月, 2010 2 次提交
  17. 07 3月, 2010 1 次提交
  19. 04 2月, 2010 2 次提交
  21. 01 1月, 2010 1 次提交
  23. 18 12月, 2009 1 次提交
  25. 02 12月, 2009 1 次提交
  27. 30 11月, 2009 1 次提交
  29. 23 10月, 2009 1 次提交
    • C
      ratelimit: Make suppressed output messages more useful · 5c828713
      由 Christian Borntraeger 提交于 
      Today I got:

  [39648.224782] Registered led device: iwl-phy0::TX
  [40676.545099] __ratelimit: 246 callbacks suppressed
  [40676.545103] abcdef[23675]: segfault at 0 ...

as you can see the ratelimit message contains a function prefix.
Since this is always __ratelimit, this wont help much.

This patch changes __ratelimit and printk_ratelimit to print the
function name that calls ratelimit.

This will pinpoint the responsible function, as long as not several
different places call ratelimit with the same ratelimit state at
the same time. In that case we catch only one random function that
calls ratelimit after the wait period.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
CC: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <200910231458.11832.borntraeger@de.ibm.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      5c828713
  31. 23 9月, 2009 2 次提交
  33. 22 9月, 2009 1 次提交
    • I
      printk: Remove ratelimit.h from kernel.h · 3fff4c42
      由 Ingo Molnar 提交于 
      Decouple kernel.h from ratelimit.h: the global declaration of
printk's ratelimit_state is not needed, and it leads to messy
circular dependencies due to ratelimit.h's (new) adding of a
spinlock_types.h include.

Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: David S. Miller <davem@davemloft.net>
LKML-Reference: <new-submission>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      3fff4c42
  35. 15 9月, 2009 1 次提交
  37. 09 8月, 2009 1 次提交
  39. 10 7月, 2009 2 次提交
    • F
      printk: Restore previous console_loglevel when re-enabling logging · 1aaad49e
      由 Frans Pop 提交于 
      When logging to console is disabled from userspace using klogctl()
and later re-enabled, console_loglevel gets set to the default
log level instead to the previous value.

This means that if the kernel was booted with 'quiet', the boot is
suddenly no longer quiet after logging to console gets re-enabled.

Save the current console_loglevel when logging is disabled and
restore to that value. If the log level is set to a specific value
while disabled, this is interpreted as an implicit re-enabling of
the logging.

The problem that prompted this patch is described in:

    http://lkml.org/lkml/2009/6/28/234

There are two variations possible on the patch below:

 1) If klogctl(7) is called while logging is not disabled, then set level
    to default (partially preserving current functionality):
  	case 7:		/* Enable logging to console */
 -		console_loglevel = default_console_loglevel;
 +		if (saved_console_loglevel == -1)
 +			console_loglevel = default_console_loglevel;
 +		else {
 +			console_loglevel = saved_console_loglevel;
 +			saved_console_loglevel = -1;
 +		}

 2) If klogctl(8) is called while logging is disabled, then don't enable
    logging, but remember the requested value for when logging does get
    enabled again:
  	case 8:		/* Set level of messages printed to console */
 [...]
 - 		console_loglevel = len;
 +		if (saved_console_loglevel == -1)
 +			console_loglevel = len;
 +		else
 +			saved_console_loglevel = len;

Yet another option would be to ignore the request.
Signed-off-by: NFrans Pop <elendil@planet.nl>
Cc: cryptsetup@packages.debian.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <200907061331.49930.elendil@planet.nl>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      1aaad49e
    • R
      printk: Ensure that "console enabled" messages are printed on the console · 8259cf43
      由 Robin Getz 提交于 
      Today, when a console is registered without CON_PRINTBUFFER,
end users never see the announcement of it being added, and
never know if they missed something, if the console is really
at the start or not, and just leads to general confusion.

This re-orders existing code, to make sure the console is
added, before the "console [%s%d] enabled" is printed out -
ensuring that this message is _always_ seen.

This has the desired/intended side effect of making sure that
"console enabled:" messages are printed on the bootconsole, and
the real console. This does cause the same line is printed
twice if the bootconsole and real console are the same device,
but if they are on different devices, the message is printed to
both consoles.

Signed-off-by : Robin Getz <rgetz@blackfin.uclinux.org>
Cc: "Andrew Morton" <akpm@linux-foundation.org>
Cc: "Linus Torvalds" <torvalds@linux-foundation.org>
LKML-Reference: <200907091308.37370.rgetz@blackfin.uclinux.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      8259cf43
  41. 03 7月, 2009 1 次提交
    • R
      printk: Enable the use of more than one CON_BOOT (early console) · 4d091611
      由 Robin Getz 提交于 
      Today, register_console() assumes the following usage:

  - The first console to register with a flag set to CON_BOOT
    is the one and only bootconsole.

  - If another register_console() is called with an additional
    CON_BOOT, it is silently rejected.

  - As soon as a console without the CON_BOOT set calls
    registers the bootconsole is automatically unregistered.

  - Once there is a "real" console - register_console() will
    silently reject any consoles with it's CON_BOOT flag set.

In many systems (alpha, blackfin, microblaze, mips, powerpc,
sh, & x86), there are early_printk implementations, which use
the CON_BOOT which come out serial ports, vga, usb, & memory
buffers.

In many embedded systems, it would be nice to have two
bootconsoles - in case the primary fails, you always have
access to a backup memory buffer - but this requires at least
two CON_BOOT consoles...

This patch enables that functionality.

With the change applied, on boot you get (if you try to
re-enable a boot console after the "real" console has been
registered):

  root:/> dmesg | grep console
  bootconsole [early_shadow0] enabled
  bootconsole [early_BFuart0] enabled
  Kernel command line: root=/dev/mtdblock0 rw earlyprintk=serial,uart0,57600 console=ttyBF0,57600 nmi_debug=regs
  console handover:boot [early_BFuart0] boot [early_shadow0]  -> real [ttyBF0]
  Too late to register bootconsole early_shadow0

or:

  root:/> dmesg | grep console
  Kernel command line: root=/dev/mtdblock0 rw console=ttyBF0,57600
  console [ttyBF0] enabled
Signed-off-by: NRobin Getz <rgetz@blackfin.uclinux.org>
Cc: "Linus Torvalds" <torvalds@linux-foundation.org>
Cc: "Andrew Morton" <akpm@linux-foundation.org>
Cc: "Mike Frysinger" <vapier.adi@gmail.com>
Cc: "Paul Mundt" <lethal@linux-sh.org>
LKML-Reference: <200907012108.38030.rgetz@blackfin.uclinux.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      4d091611
  43. 17 6月, 2009 2 次提交
    • L
      printk: Add KERN_DEFAULT printk log-level · e28d7137
      由 Linus Torvalds 提交于 
      This adds a KERN_DEFAULT loglevel marker, for when you cannot decide
which loglevel you want, and just want to keep an existing printk
with the default loglevel.

The difference between having KERN_DEFAULT and having no log-level
marker at all is two-fold:

 - having the log-level marker will now force a new-line if the
   previous printout had not added one (perhaps because it forgot,
   but perhaps because it expected a continuation)

 - having a log-level marker is required if you are printing out a
   message that otherwise itself could perhaps otherwise be mistaken
   for a log-level.
Signed-of-by: NLinus Torvalds <torvalds@linux-foundation.org>
      e28d7137
    • L
      printk: clean up handling of log-levels and newlines · 5fd29d6c
      由 Linus Torvalds 提交于 
      It used to be that we would only look at the log-level in a printk()
after explicit newlines, which can cause annoying problems when the
previous printk() did not end with a '\n'. In that case, the log-level
marker would be just printed out in the middle of the line, and be
seen as just noise rather than change the logging level.

This changes things to always look at the log-level in the first
bytes of the printout. If a log level marker is found, it is always
used as the log-level. Additionally, if no newline existed, one is
added (unless the log-level is the explicit KERN_CONT marker, to
explicitly show that it's a continuation of a previous line).
Acked-by: NArjan van de Ven <arjan@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      5fd29d6c
  45. 03 4月, 2009 1 次提交
  47. 17 3月, 2009 1 次提交
    • G
      printk: correct the behavior of printk_timed_ratelimit() · f2d28a2e
      由 Guillaume Knispel 提交于 
      Impact: fix jiffies-comparison sign-wrap behavior

The behavior provided by printk_timed_ratelimit() is, in some
situations, probably not what a caller would reasonably expect:

bool printk_timed_ratelimit(unsigned long *caller_jiffies,
			unsigned int interval_msecs)
{
	if (*caller_jiffies == 0 || time_after(jiffies, *caller_jiffies)) {
		*caller_jiffies = jiffies + msecs_to_jiffies(interval_msecs);
		return true;
	}
	return false;
}

On a 32 bit computer, if printk_timed_ratelimit() is initially called at
time jiffies == Ja, *caller_jiffies is set to
Ja + msecs_to_jiffies(interval_msecs): let's say Ja + 42 for this
example.

If this caller then doesn't call printk_timed_ratelimit() until
jiffies == Ja + (1 << 31) + 42 (which can happen as soon as ~ 25 days
later on a 1000 HZ system), printk_timed_ratelimit() will then always
return false to this caller until jiffies loops completely (1 << 31 more
ticks).

Ths change makes it only return false if jiffies is in the small
time window starting at the previous call when true was returned and
ending interval_msecs later.  Note that if jiffies loops completely
between two calls to printk_timed_ratelimit(), it will obviously still
wrongly return false, but this is something with a low probability.

If something completely reliable is needed I guess jiffies_64 must be
used (which this change does not do).
Signed-off-by: NGuillaume Knispel <gknispel@proformatique.com>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20090317161842.0059096b@xilun.lan.proformatique.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      f2d28a2e
  49. 22 2月, 2009 1 次提交
    • A
      PM: Fix suspend_console and resume_console to use only one semaphore · 403f3075
      由 Arve Hjønnevåg 提交于 
      This fixes a race where a thread acquires the console while the
console is suspended, and the console is resumed before this
thread releases it. In this case, the secondary console
semaphore would be left locked, and the primary semaphore would
be released twice. This in turn would cause the console switch
on suspend or resume to hang forever.

Note that suspend_console does not actually lock the console
for clients that use acquire_console_sem, it only locks it for
clients that use try_acquire_console_sem. If we change
suspend_console to fully lock the console, then the kernel
may deadlock on suspend. One client of try_acquire_console_sem
is acquire_console_semaphore_for_printk, which uses it to
prevent printk from using the console while it is suspended.
Signed-off-by: NArve Hjønnevåg <arve@android.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      403f3075
  51. 14 1月, 2009 2 次提交
  53. 06 1月, 2009 1 次提交
  55. 20 12月, 2008 1 次提交
  57. 24 10月, 2008 1 次提交
  59. 17 10月, 2008 3 次提交