In hostap AP mode, every time the client sends the AP
a packet the STA_NOTIFY_AWAKE code is sent from mac80211.
This results in a command being sent to the uCode even if
the client was not asleep.

The following simple patch has fixed the issue for me without any
degradation that I can find.
Signed-off-by: NDaniel Halperin <dhalperi@cs.washington.edu>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

IDLE PS (Full Sleep) doesn't work when ifconfig up
is done during Idle unassociated state.
Fix this by restoring FULL SLEEP in ps_restore if CONF_IDLE
is set.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the association worker requests a directed ssid scan and a bss list
already exists, the directed scan is not done. This patch corrects this
and cleans up a few typos and debug messages.
Signed-off-by: NHamish Guthrie <hamish.guthrie@sonycom.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current PS3 gelic wireless driver has support for wireless
extensions. The original PS3 gelic wireless driver exposed a
dedicated API for a dedicated wpa_supplicant driver. This old
API could be enabled with CONFIG_GELIC_WIRELESS_OLD_PSK_INTERFACE,
however, as this is not being used by any distros, and it is being
removed from the driver and from wpa_supplicant.
Signed-off-by: NHamish Guthrie <hamish.guthrie@sonycom.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the conversion between typedef and struct, two places that needed a "struct"
were missed.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Comment text suggested by Dan Williams <dcbw@redhat.com> in
<1263952092.4481.2.camel@localhost.localdomain>.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With following patch, LED should now work with LiteOn AR5BXB63 mini
pci-e cards.

(Broken patch fixed-up by me...let's hope I did it right! -- JWL)
Signed-off-by: NLuca Verdesca <magooz@salug.it>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Because DTIM information is required for powersave
but is only conveyed in beacons, wait for a beacon
before enabling powersave, and change the way the
information is conveyed to the driver accordingly.

mwl8k doesn't currently seem to implement PS but
requires the DTIM period in a different way; after
talking to Lennert we agreed to just have mwl8k do
the parsing itself in the finalize_join work.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This new function (previously a static function
called just "find_ie" can be used to find a
specific IE in a buffer of IEs.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Filtered frames not only need their control information
cleared to avoid wrong checks, but also need to have
jiffies and vif assigned so they can be processed or
expired.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, the remain_on_channel work callback needs
to track in its own data structure whether the work
was just started or not. By reordering some code this
becomes unnecessary, the generic wk->started variable
can still be 'false' on the first invocation and only
be 'true' on actual timeout invocations, so that the
extra variable can be removed.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

What a stupid mistake. In

    commit 813d7669
    Author: Johannes Berg <johannes@sipsolutions.net>
    Date:   Sun Jan 17 01:47:58 2010 +0100

        mac80211: move control.hw_key assignment

I inserted code testing the wrong flags field,
which means that the test is almost always true
(it's really testing for the peer's WMM support)
and thus the later parts of the stack assume hw
crypto will be done even if that's not true.

Obviously, that broke software crypto. Maxim
said so specifically, and Jochen probably uses
some cipher that iwl3945 doesn't support in
hardware, which might also explain that Maxim
reports that even hw crypto is broken.

Fix this to test the right flags field.
Reported-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Reported-by: NJochen Friedrich <jochen@scram.de>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_work_rx_mgmt currently enqueues various management frames,
including deauth and disassoc frames, however the function
ieee80211_work_rx_queued_mgmt does not handle these, as they should
only occur if the AP is buggy. It does emit a WARN_ON when this happens
though, and several users have reported such instances.
Fix the WARN_ON by not queueing such frames in the first place.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Johannes noticed that I had incorrectly documented the context of
update_tkip_key() driver operation. It must be atomic because all
RX code is run inside rcu critical section.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The TKIP key update callback is called from the RX path, where the driver
mutex is already locked. This results in a circular locking bug.
Avoid this by removing the lock.

Johannes noted that there is a separate bug: The callback still breaks on SDIO
hardware, because SDIO hardware access needs to sleep, but we are not allowed
to sleep in the callback due to mac80211's RCU locking.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reported-by: kecsa@kutfo.hit.bme.hu
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k currently forces hw->max_rate_tries to 4 to work around rate
control inefficiencies. This has some negative side effects, such as
rate_control_send_low also using a maximum of 4 tries, which could
negatively affect reliability of unicast management frames.
This patch pushes the retry limit to the rate control instead, and
allows it to use more tries on the last stage to prevent unnecessary
packet loss.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The following commit

	commit e4da8c37
	Author: Johannes Berg <johannes@sipsolutions.net>
	Date:   Wed Dec 23 13:15:43 2009 +0100

	   mac80211: make off-channel work generic

triggered a bug in iwlwifi where HT parameters would not be correctly set in
some mac80211 pathways. The aggregation (and possibly other) station flags were
not being set, which limited the size of aggregation blocks and reduced
throughput at high rates.

>From Johannes:
"""
Due to Wey-Yi's patch to use the set-channel command when the channel changes
while associated, we don't get a full new RXON. Therefore, we don't re-set the
rxon-station either. However, under some circumstances that apparently have
gotten more likely mac80211 will first set up the BSS info, then add the
station and then switch to an HT channel type.

Therefore, the check for "priv->current_ht_config.is_ht" in
iwl_rxon_add_station() will hit false and not fill in the HT information.

However, that check can just be removed, which is the easiest fix for all this,
because the HT capa struct is always there, just could possibly have the
ht_supported member set to false.
"""

A sample good link in my 3x3 network improves by approximately 25% TCP
throughput. This fixes Bug 2144
(http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2144).
Signed-off-by: NDaniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In iwlagn the support for spectrum measurement command has been
disabled since v2.6.29 without any requests for it. In addition to this
when this command is indeed enabled it has been found to trigger firmware
SYSASSERT on at least 4965 and 5100 hardware (see
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1952 ). Since then
this code has been bitrotting and cannot just be enabled without porting.

Remove support for spectrum measurement command from iwlagn. It can be
added back if there is a future need and the firmware problem it triggers
has been fixed. Support for the spectrim measurement notification remains
as it has been enabled all the time.

In addition to this remove the 3945 spectrum measurement command Kconfig
option and make this command always supported. The code added by this
enabling is minimal and only run when user triggers a spectrum measurement
request via sysfs.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sparse won't check endianness annotations by
default, but iwlwifi is and should be clean
so we can make sparse check them on it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sparse correctly warns about symbol not
being static, make static to shut it up.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The debugfs code can be made a whole lot more
efficient by using debugfs_remove_recursive(),
the large chunk of variables can completely go
away and by moving two variables we no longer
need to allocate an extra chunk of memory.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is better to first notify cfg80211 about the hw
rfkill state (so the rfkill device that will be
registered won't have the wrong state while being
registered), and the power/tt variable init can
(and probably should) also be done first.

Also rename iwl_setup_mac to
iwl_mac_setup_register to better describe what it
really does.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It really hasn't been for a long time, not sure
why this stuck around.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding "bt_coex_active" module parameter for iwlcore to enable/disable
BT coexist; if bt_coex_active is true (default), uCode will do kill/defer
every time the priority line is asserted (BT is sending signals on the
priority line in the PCIx). By disable the bt_coex_active, uCode will
ignore the BT activity and perform the normal operation.

Users might experience transmit issue on some platform due to this
WiFi/BT co-exist problem. The possible symptoms are: NetworkManager and
other similar programs can scan and find all the available APs, but will
timeout and unable to associate with any of the APs; no out-going frames
can be found with wireless sniffer tools.

On those platforms, WiFi communication can be restored by set "bt_coex_active"
module parameter to "false"
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Give better bit filed define and description for flag parameter
in REPLY_BT_CONFIG command:

flags:
 bit 0 - 1: BT channel announcement enabled
         0: disable
 bit 1 - 1: priority of BT device enabled
         0: disable
 bit 2 - 1: BT 2 wire support enabled
         0: disable
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add function pointer for broadcast station addition so that we can call it
in from iwlcore at a later time. We only distinguish between iwlagn and
iwl3945 broadcast station addition. For the iwl3945 station addition we add
that function to iwlcore since that is where most station functionality
resides, making it part of iwl3945 will require significant code
reorganization that will dilute station management functionality. This
seems to be an efficient solution.

It may seem as though we are removing error checking when adding the 3945
broadcast station but this error checking was never really necessary since
the function returns the station id and the broadcast station id is always
set.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The work done when a station is added is very similar whether the station
is added synchronously or asynchronously. Centralize this work. At the same
time increase the status flags being checked for when the command returns
with accompanying debug messages. Also increase checking when setting the
"ucode active" state with accompanying debugging.

This work is done in preparation for station notification support.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

From: Abhijeet Kolekar <abhijeet.kolekar@intel.com>

For 6X50 DC calibration needs to be initialized
else uCode will run an endless loop.
Enbale DC calibration in hw config.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have seen the throughput dropped due to external noisy environment
and the radio is out of tune.  There are lot of plcp errors indicating
this condition. Eventually the station can get de-authenticated by the
Access Point.  By resetting and tuning the radio, the plcp errors are
reduced or eliminated and the throughput starts to rise.

To prevent unexpected behavior such as drop in throughput or deauthentication,
- The change provides the driver feature to monitor and tune the radio base on
the statistics notification from the uCode.
- It also allows the setting of the plcp error rate threshold via
the plcp_delta under debugfs interface.
Signed-off-by: NTrieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add additional logic for internal scan routine to control how
frequent this function should be performed.

The intent of this function is to reset/re-tune the radio and bring the
RF/PHY back to normal state, it does not make sense calling it too
frequent,
if reset the radio can not bring it back to normal state, it indicate
there are other reason to cause the radio not operate correctly.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch allows A band to be scanned when driver is associated to AP.
Scan mechanism is that mac80211/cfg80211 requests driver to scan G band
first and then immediately to scan A band. Original code require
driver to wait for 2 seconds after any scan before another scan will be
performed. This caused driver to service G band scan request from
mac80211/cfg80211 but deny the A band scan request.
Signed-off-by: NHenry Zhangh <hongx.c.zhang@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding "radio reset" function to help reset and stabilize the radio.

During normal operation, sometime for unknown reason, radio encounter
problem and can not recover by itself; the best way to
recover from it is to reset and re-tune the radio. Currently, there is
no RF reset command available, but since radio will get reset when
switching channel, use internal hw scan request to force radio
reset and get back to normal operation state.

The internal hw scan will only perform passive scan on the first
available channel (not the channel being used) in associated state. The
request should be ignored if already performing scan operation or STA is
not in associated state.

Also include an "internal_scan" debugfs file to help trigger the
internal scan from user mode.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support to configure missed beacon threshold, by default, if receive
"missed beacon" notification from uCode and has more than 5 consecutive
beacon missed, then perform sensitivity calibration; with this change,
allow user to adjust the missed beacon threshold from debugfs in case
more sensitivity calibration required for better performance in noisy
environment

The default value (=5) should be good enough for the normal condition,
but for very noisy environment, more sensitivity calibration could help
improve the throughput, so by setting the missed beacon threshold to
lower number, user might experience better performance result.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>