Update version number
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

A driver writer from another operating system hinted that
the versions of Yukon 2 chip with rambuffer (EC and XL) have
a hardware bug that if the FIFO ever gets completely full it
will hang. Sounds like a classic ring full vs ring empty wrap around
bug.

As a workaround, use the existing watchdog timer to check for
ring full lockup.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add support for newest Marvell chips.
The Yukon FE plus chip is found in some not yet released laptops.
Tested on hardware evaluation boards.

This version of the patch is for 2.6.23. It supersedes
the two previous patches that are sitting in netdev-2.6 (upstream branch).
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch should cause no functional changes in driver behaviour.
There are (too) many revisions of the Yukon 2 chip now. Instead of
adding more conditionals based on chip revision; rerganize into a
set of feature flags so adding new versions is less problematic.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

On 100mbit versions, the driver always reports gigabit speed
available. The correct modes are already computed, then overwritten.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The length check for truncated frames was not correctly handling
the case where VLAN acceleration had already read the tag.
Also, the Yukon EX has some features that use high bit of status
as security tag.
Signed-off-by: NPierre-Yves Ritschard <pyr@spootnik.org>
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Need to restore multicast settings on resume and after 'ethtool -r'.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Mark new version to track if current driver is in use.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This fixes the extra timer overhead that people were whining about
as a 2.6.23 regression.

Running the watchdog timer all the time is unneeded. Change it
to run only if link is up, and reduce frequency to save power.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make sure PCI register for PHY power gets cleared on boot, and make
sure to avoid any PCI posting problems.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There are special PHY settings available on Yukon EC-U chip that
should not get cleared. This should solve mysterious errors on some
motherboards (like Gigabyte DS-3).
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function.  So we can inline the generic function into the
caller and avoid going through the drivers.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

	Doing |= 1 << 19 to 16bit unsigned is not particulary useful;
that register is 32bit, unlike the ones dealt with in the rest of
function, so we need u32 variable here.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Eliminate extra debug messages
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use upper_32_bits() inline
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use roundup() macro to size receive buffer.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If packet larger than MTU is received, the driver uses hardware to
truncate the packet. Use the status registers to catch/drop them.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add get/set eeprom support for sky2.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Simplify receive buffer refill logic. Rather than trying to update
incrementally; do receive ring refill at end of receive processing.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch avoids generating another IRQ if more packets
arrive while in the NAPI poll routine. Before marking device as
finished, it rechecks that the status ring is empty.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add an optional debug interface for displaying state of transmit/receive
rings. Creates a file debugfs/sky2/ethX for each device that is up.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make sky2 handle carrier similar to other drivers,
eliminate some possible races in carrier state transistions.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch restores a couple of workarounds from 2.6.16:
 * restart transmit moderation timer in case it expires during IRQ routine
 * default to having 10 HZ watchdog timer.
At this point it more important not to hang than to worry about the
power cost.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

New version because of new chip support.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Enable support for Yukon EX chipset (88e8071).
Most of changes are related to new commands to chip for transmit,
and change in status and checksumming.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The General Purpose I/O register is yet another hardware workaround
catchall. Enable workaround that vendor driver does to stay
but for bug compatiable.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Catch-22: On Yukon EX (88E8071) need to have internal clocks enabled
before reading chip id. It is harmless on other chips.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This register is more of a test and control register on Yukon2.
So rename it to Q_TEST and give some bit definitions.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Need to setup more PCI control control registers are on Yukon EX.
Some of these also exist on Yukon EC-U as well.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

On Yukon EX reading some of the undocumented places in the
memory space will cause a hang. Since they don't provide useful
information, just skip the reserved areas.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix sky2 disabling VLAN completely when the first vid is unregistered.

sky2 disables VLAN completely when the first VID is unregistered. It
should instead disable VLAN when the group is unregistered by calling
sky2_vlan_rx_register with grp = NULL.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>

 drivers/net/sky2.c |   25 +++++++++++++------------
 1 file changed, 13 insertions(+), 12 deletions(-)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Driver was reading value from one register, setting bit and then
writing the wrong register.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Driver was not correctly setting up transmit descriptor when doing
VLAN tag insertion with checksum offload.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This code inherited from the sk98lin driver is incorrect on the Yukon2.
The GPHY_CTRL register values are specific to the internal PHY of the chip
and the values used were leftovers.
Driver was setting bit 13 which is now the INT polarity for the PHY!
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Do some memory barrier changes for safety/perfomance:
Don't need read after update to index, mmiowb() followed by read at end
of irq is sufficient.
Signed-off-by: NStephn Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This workaround was added to deal with NAPI core and how
it affected dual port shared polling. It turned out not to
be necessary. Stopping device 0 only doesn't stop NAPI from
working completely after that.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make sure that if we ever get a MIB counter overflow interrupt (normally
masked off), that the IRQ is cleared.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When driver can't allocate receive buffer it drops incoming
packet. Keep a counter.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Align the PHY setup of the sky2 driver with the vendor sk98lin (10.0.4.3)
driver. The PHY register settings are mostly black magic, even with access
to the documentation it isn't clear what the right values are. The changes
are mostly comments, the code change only affects the Yukon FE (100 mbit only)
version.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>