Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 29 4月, 2007 10 次提交
    • T
      libata: allocate ap separately from shost · 4911487a
      由 Tejun Heo 提交于 
      Don't embed ap inside shost.  Allocate it separately and point it back
from shosts's hostdata.  This makes port allocation more flexible and
allows regular ATA and SAS share host alloc/init paths.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
      4911487a
    • C
      ahci.c: remove non-existing SB600 raid id (re-send) · c65ec1c2
      由 Conke Hu 提交于 
          SB600 RAID and SB600 SATA is the same controller and share the
same PCI ID 0x4380. There is no such PCI ID 0x4381.
Signed-off-by: NConke Hu <conke.hu@gmail.com>
 ---------
Signed-off-by: NJeff Garzik <jeff@garzik.org>
      c65ec1c2
    • M
      libata: add support for READ/WRITE LONG · 5a5dbd18
      由 Mark Lord 提交于 
      The READ/WRITE LONG commands are theoretically obsolete,
but the majority of drives in existance still implement them.

The WRITE_LONG and WRITE_LONG_ONCE commands are of particular
interest for fault injection testing -- eg. creating "media errors"
at specific locations on a disk.

The fussy bit is that these commands require a non-standard
sector size, usually 520 bytes instead of 512.

This patch adds support to libata for READ/WRITE LONG commands
issued via SG_IO/ATA_16.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
      5a5dbd18
    • J
      libata/IDE: remove combined mode quirk · 8cdfb29c
      由 Jeff Garzik 提交于 
      Both old-IDE and libata should be able handle all controllers and
devices found using normal resource reservation methods.

This eliminates the awful, low-performing split-driver configuration
where old-IDE drove the PATA portion of a PCI device, in PIO-only mode,
and libata drove the SATA portion of the /same/ PCI device, in DMA mode.
Typically vendors would ship SATA hard drive / PATA optical
configuration, which would lend itself to slow (PIO-only) CD-ROM
performance.

For Intel users running in combined mode, it is now wholly dependent on
your driver choice (potentially link order, if you compile both drivers
in) whether old-IDE or libata will drive your hardware.

In either case, you will get full performance from both SATA and PATA
ports now, without having to pass a kernel command line parameter.
Signed-off-by: NJeff Garzik <jeff@garzik.org>
      8cdfb29c
    • A
      libata: Change prototype of mode_filter to remove ata_port* · a76b62ca
      由 Alan Cox 提交于 
      With Tejun having added adev->ap some time ago we can get rid of the
almost unused port being passed to mode filters. And while we are
doing filters, lets turn on the !IORDY filter as well.
Signed-off-by: NAlan Cox <alan@redhat.com>

With some hand massaging from
Signed-off-by: NJeff Garzik <jeff@garzik.org>
      a76b62ca
    • A
      pata: expose set_mode method so it can be wrapped · 04351821
      由 Alan 提交于 
      This splits set_mode into do_set_mode and the wrapper so that a driver can
call the standard method inside its own.  This in theory also obsoletes
->post_set_mode().
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
      04351821
    • T
      iomap: implement pcim_iounmap_regions() · ec04b075
      由 Tejun Heo 提交于 
      Implement pcim_iounmap_regions() - the opposite of
pcim_iomap_regions().
Signed-off-by: NTejun heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
      ec04b075
    • A
      libata: cable detection fixes · be0d18df
      由 Alan Cox 提交于 
      2.6.21-rc has horrible problems with libata and PATA cable types (and
thus speeds). This occurs because Tejun fixed a pile of other bugs and
we now do cable detect enforcement for drive side detection properly.

Unfortunately we don't do the process around cable detection right. Tejun
identified the problem and pointed to the right Annex in the spec, this patch
implements the rest of the needed changes.

We add a ->cable_detect() method called after the identify
sequence which allows a host to do host side detection at this point
should it wish, or to modify the results of the drive side identify.

This separate ->cable_detect method also cleans up a lot of code because
many drivers have their own error_handler methods which really just set
the cable type.

If there is no ->cable_detect method the cable type is left alone so a
driver setting it earlier (eg because it has the SATA flags set or
because it uses the old error_handler approach) will still do the right
thing (or at least the same thing) as before.

This patch simply adds the cable_detect method and helpers it doesn't use
them but other follow up patches will (ie Adrian please don't submit
patches to unexport them ;))
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
      be0d18df
    • A
      libata: dev_config does not need ap and adev passing · cd0d3bbc
      由 Alan 提交于 
      It used to be impossible to get from ata_device to ata_port but that is
no longer true. Various methods have been cleaned up over time but
dev_config still takes both and most users don't need both anyway. Tidy
this one up
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
      cd0d3bbc
    • J
      [libata] export sata_print_link_status() · 43727fbc
      由 Jeff Garzik 提交于 
      To be used in sata_mv's exception handling code, and overall is a
generally useful function.
Signed-off-by: NJeff Garzik <jeff@garzik.org>
      43727fbc
  3. 28 4月, 2007 30 次提交