Rx descriptor fields accordingly to the updated
hardware documentation
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Sometimes it takes for the firmware more than 20ms to
react on "echo" command after reset. Increase timeout
from 20 to 50ms
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca6174 otp binary seems to always return an error to the host, even if the
calibration succeeded. Add a firmware feature flag to detect if the firmware
image which have this problem and workaround the issue in ath10k by ignoring
the error code.

I was also considering making this hw specific flag but as this is strictly a
firmware issue it's best to handle this via a firmware feature flag so that it
will be easy to disable the workaround.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware "board" file name has changed from wil6210.board
to wil6210.brd by the FW generation tools.

Reflect this in the driver.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

cfg80211_ops.stop_ap supposed to have interface carried turned off as
post condition. Fulfill this requirement.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Trace where wil6210_disconnect() is called from.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Provide info for [add|del]_key.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

refactor module parameter debug_fw to act as "fw debug mode",
where driver do nothing but allow card memory access.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Major changes in ath10k:

* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware

Pull networking fixes from David Miller:

 1) mlx4 doesn't check fully for supported valid RSS hash function, fix
    from Amir Vadai

 2) Off by one in ibmveth_change_mtu(), from David Gibson

 3) Prevent altera chip from reporting false error interrupts in some
    circumstances, from Chee Nouk Phoon

 4) Get rid of that stupid endless loop trying to allocate a FIN packet
    in TCP, and in the process kill deadlocks.  From Eric Dumazet

 5) Fix get_rps_cpus() crash due to wrong invalid-cpu value, also from
    Eric Dumazet

 6) Fix two bugs in async rhashtable resizing, from Thomas Graf

 7) Fix topology server listener socket namespace bug in TIPC, from Ying
    Xue

 8) Add some missing HAS_DMA kconfig dependencies, from Geert
    Uytterhoeven

 9) bgmac driver intends to force re-polling but does so by returning
    the wrong value from it's ->poll() handler.  Fix from Rafał Miłecki

10) When the creater of an rhashtable configures a max size for it,
    don't bark in the logs and drop insertions when that is exceeded.
    Fix from Johannes Berg

11) Recover from out of order packets in ppp mppe properly, from Sylvain
    Rochet

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
  bnx2x: really disable TPA if 'disable_tpa' option is set
  net:treewide: Fix typo in drivers/net
  net/mlx4_en: Prevent setting invalid RSS hash function
  mdio-mux-gpio: use new gpiod_get_array and gpiod_put_array functions
  netfilter; Add some missing default cases to switch statements in nft_reject.
  ppp: mppe: discard late packet in stateless mode
  ppp: mppe: sanity error path rework
  net/bonding: Make DRV macros private
  net: rfs: fix crash in get_rps_cpus()
  altera tse: add support for fixed-links.
  pxa168: fix double deallocation of managed resources
  net: fix crash in build_skb()
  net: eth: altera: Resolve false errors from MSGDMA to TSE
  ehea: Fix memory hook reference counting crashes
  net/tg3: Release IRQs on permanent error
  net: mdio-gpio: support access that may sleep
  inet: fix possible panic in reqsk_queue_unlink()
  rhashtable: don't attempt to grow when at max_size
  bgmac: fix requests for extra polling calls from NAPI
  tcp: avoid looping in tcp_send_fin()
  ...

bnx2x's 'disable_tpa=1' module option is not respected properly and TPA
(transparent packet aggregation) remains enabled. Even though the
module option causes LRO to be disabled, TPA is enabled in GRO mode.

Additionally, disabling GRO via ethtool then has no effect. One can
still observe tpa_* statistics increase and large packets being received
in tcpdump.

The bug was an unintended consequence of commit aebf6244 "bnx2x: Be
more forgiving toward SW GRO".

Fix it by following the bp->disable_tpa flag when initializing fp's.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fix spelling typo in printk.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx4_en_check_rxfh_func() was checking for hardware support before
setting a known RSS hash function, but didn't do any check before
setting unknown RSS hash function. Need to make it fail on such values.
In this occasion, moved the actual setting of the new value from the
check function into mlx4_en_set_rxfh().

Fixes: 947cbb0a ("net/mlx4_en: Support for configurable RSS hash function")
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the new gpiod_get_array and gpiod_put_array functions
(added to mainline in the v4.1 merge window) for obtaining and
disposing of GPIO descriptors.

Cc: David Miller <davem@davemloft.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes:

====================
net/netfilter/nft_reject.c: In function ‘nft_reject_dump’:
net/netfilter/nft_reject.c:61:2: warning: enumeration value ‘NFT_REJECT_TCP_RST’ not handled in switch [-Wswitch]
  switch (priv->type) {
  ^
net/netfilter/nft_reject.c:61:2: warning: enumeration value ‘NFT_REJECT_ICMPX_UNREACH’ not handled in switch [-Wswi\
tch]
net/netfilter/nft_reject_inet.c: In function ‘nft_reject_inet_dump’:
net/netfilter/nft_reject_inet.c:105:2: warning: enumeration value ‘NFT_REJECT_TCP_RST’ not handled in switch [-Wswi\
tch]
  switch (priv->type) {
  ^
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until now only a single fixed tx rate or nss was
allowed to be set.

The patch attempts to improve this by allowing
most bitrate masks. The limitation is VHT MCS
rates cannot be expressed separately using
existing firmware interfaces and only the
following VHT MCS ranges are supported: none, 0-7,
0-8, and 0-9.

This keeps the old behaviour when requesting
single tx rate or single nss. The new bitrate mask
logic is only applied to other cases that would
return -EINVAL until now.

Depending on firmware revisions some combinations
may crash firmware so use with care, please.

This depends on "ath10k: don't use reassoc flag".
Without it key cache would effectively be
invalidated upon bitrate change leading to
communication being no longer possible.

These work:

  iw wlan0 set bitrates legacy-5 6 12 ht-mcs-5 1 2 3
  iw wlan0 set bitrates legacy-5 ht-mcs-5 7 8 9
  iw wlan0 set bitrates legacy-5 24 ht-mcs-5 vht-mcs-5 1:0-9

These won't work:

  iw wlan0 set bitrates legacy-5 ht-mcs-5 vht-mcs-5 1:0-5
  iw wlan0 set bitrates vht-mcs-5 2:7-9

(note the invalid VHT MCS ranges)
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Sylvain Rochet says:

====================
ppp: mppe: fixes MPPE desync on links which don't guarantee packet ordering

I am currently having an issue with PPP over L2TP (UDP) and MPPE in
stateless mode (default mode), UDP does not guarantee packet ordering so
we might get out of order packet. MPPE needs to be continuously synched
so we should drop late UDP packet.

I added a printk on the number of time we rekeyed in MPPE decompressor,
this is what we currently have if we receive a slightly out of order UDP
packet:

[1731001.049206] mppe_decompress[1]: ccount 1559
[1731001.049216] mppe_decompress[1]: rekeyed 1 times

[1731001.049228] mppe_decompress[1]: ccount 1560
[1731001.049232] mppe_decompress[1]: rekeyed 1 times

[1731001.050170] mppe_decompress[1]: ccount 1562
[1731001.050182] mppe_decompress[1]: rekeyed 2 times

[1731001.050191] mppe_decompress[1]: ccount 1561
[1731001.062576] mppe_decompress[1]: rekeyed 4095 times
                                             ^^^^
This is obviously wrong, we missed packet 1561 and we already rekeyed 2
times for 1562 we previously received, we can't recover the decryption
key we need for 1561, we should drop it instead of rekeying 4095 times.

This patch series drop any packet with are not within the 4096/2 forward
window.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PPP is used over a link which does not guarantee packet ordering,
we might get late MPPE packets. This is a problem because MPPE must be
kept synchronized and the current implementation does not drop them and
rekey 4095 times instead of 0, which is wrong.

In order to prevent rekeying about a whole count space times (~ 4095
times), drop packets which are not within the forward 4096/2 window and
increase sanity error counter.
Signed-off-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are going to need sanity error path a little further, rework to be
able to use the sanity error path anywhere in decompressor.
Signed-off-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bonding modules currently defines four macros with
general names that pollute the global namespace:
DRV_VERSION
DRV_RELDATE
DRV_NAME
DRV_DESCRIPTION

Fixing that by defining a private bonding_priv.h
header files which includes those defines.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

AMD CPUs don't reinitialize the SS descriptor on SYSRET, so SYSRET with
SS == 0 results in an invalid usermode state in which SS is apparently
equal to __USER_DS but causes #SS if used.

Work around the issue by setting SS to __KERNEL_DS __switch_to, thus
ensuring that SYSRET never happens with SS set to NULL.

This was exposed by a recent vDSO cleanup.

Fixes: e7d6eefa x86/vdso32/syscall.S: Do not load __USER32_DS to %ss
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Brian Gerst <brgerst@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull intel drm fixes from Dave Airlie.

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: vlv: fix save/restore of GFX_MAX_REQ_COUNT reg
  drm/i915: Workaround to avoid lite restore with HEAD==TAIL
  drm/i915: cope with large i2c transfers

Pull intel iommu updates from David Woodhouse:
 "This lays a little of the groundwork for upcoming Shared Virtual
  Memory support — fixing some bogus #defines for capability bits and
  adding the new ones, and starting to use the new wider page tables
  where we can, in anticipation of actually filling in the new fields
  therein.

  It also allows graphics devices to be assigned to VM guests again.
  This got broken in 3.17 by disallowing assignment of RMRR-afflicted
  devices.  Like USB, we do understand why there's an RMRR for graphics
  devices — and unlike USB, it's actually sane.  So we can make an
  exception for graphics devices, just as we do USB controllers.

  Finally, tone down the warning about the X2APIC_OPT_OUT bit, due to
  persistent requests.  X2APIC_OPT_OUT was added to the spec as a nasty
  hack to allow broken BIOSes to forbid us from using X2APIC when they
  do stupid and invasive things and would break if we did.

  Someone noticed that since Windows doesn't have full IOMMU support for
  DMA protection, setting the X2APIC_OPT_OUT bit made Windows avoid
  initialising the IOMMU on the graphics unit altogether.

  This means that it would be available for use in "driver mode", where
  the IOMMU registers are made available through a BAR of the graphics
  device and the graphics driver can do SVM all for itself.

  So they started setting the X2APIC_OPT_OUT bit on *all* platforms with
  SVM capabilities.  And even the platforms which *might*, if the
  planets had been aligned correctly, possibly have had SVM capability
  but which in practice actually don't"

* git://git.infradead.org/intel-iommu:
  iommu/vt-d: support extended root and context entries
  iommu/vt-d: Add new extended capabilities from v2.3 VT-d specification
  iommu/vt-d: Allow RMRR on graphics devices too
  iommu/vt-d: Print x2apic opt out info instead of printing a warning
  iommu/vt-d: kill bogus ecap_niotlb_iunits()

Pull i2c fixes from Wolfram Sang:
 "This has a mixture of merge window cleanups and bugfixes"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: st: add include for pinctrl
  i2c: mux: use proper dev when removing "channel-X" symlinks
  i2c: digicolor: remove duplicate include
  i2c: Mark adapter devices with pm_runtime_no_callbacks
  i2c: pca-platform: fix broken email address
  i2c: mxs: fix broken email address
  i2c: rk3x: report number of messages transmitted

Pull btrfs fixes from Chris Mason:
 "Filipe hit two problems in my block group cache patches.  We finalized
  the fixes last week and ran through more tests"

* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: prevent list corruption during free space cache processing
  Btrfs: fix inode cache writeout

Merge tag 'drm-intel-next-fixes-2015-04-25' of git://anongit.freedesktop.org/drm-intel into drm-fixes

three fixes for i915.

* tag 'drm-intel-next-fixes-2015-04-25' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: vlv: fix save/restore of GFX_MAX_REQ_COUNT reg
  drm/i915: Workaround to avoid lite restore with HEAD==TAIL
  drm/i915: cope with large i2c transfers

Pull NFS client updates from Trond Myklebust:
 "Another set of mainly bugfixes and a couple of cleanups.  No new
  functionality in this round.

  Highlights include:

  Stable patches:
   - Fix a regression in /proc/self/mountstats
   - Fix the pNFS flexfiles O_DIRECT support
   - Fix high load average due to callback thread sleeping

  Bugfixes:
   - Various patches to fix the pNFS layoutcommit support
   - Do not cache pNFS deviceids unless server notifications are enabled
   - Fix a SUNRPC transport reconnection regression
   - make debugfs file creation failure non-fatal in SUNRPC
   - Another fix for circular directory warnings on NFSv4 "junctioned"
     mountpoints
   - Fix locking around NFSv4.2 fallocate() support
   - Truncating NFSv4 file opens should also sync O_DIRECT writes
   - Prevent infinite loop in rpcrdma_ep_create()

  Features:
   - Various improvements to the RDMA transport code's handling of
     memory registration
   - Various code cleanups"

* tag 'nfs-for-4.1-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (55 commits)
  fs/nfs: fix new compiler warning about boolean in switch
  nfs: Remove unneeded casts in nfs
  NFS: Don't attempt to decode missing directory entries
  Revert "nfs: replace nfs_add_stats with nfs_inc_stats when add one"
  NFS: Rename idmap.c to nfs4idmap.c
  NFS: Move nfs_idmap.h into fs/nfs/
  NFS: Remove CONFIG_NFS_V4 checks from nfs_idmap.h
  NFS: Add a stub for GETDEVICELIST
  nfs: remove WARN_ON_ONCE from nfs_direct_good_bytes
  nfs: fix DIO good bytes calculation
  nfs: Fetch MOUNTED_ON_FILEID when updating an inode
  sunrpc: make debugfs file creation failure non-fatal
  nfs: fix high load average due to callback thread sleeping
  NFS: Reduce time spent holding the i_mutex during fallocate()
  NFS: Don't zap caches on fallocate()
  xprtrdma: Make rpcrdma_{un}map_one() into inline functions
  xprtrdma: Handle non-SEND completions via a callout
  xprtrdma: Add "open" memreg op
  xprtrdma: Add "destroy MRs" memreg op
  xprtrdma: Add "reset MRs" memreg op
  ...

Pull fourth vfs update from Al Viro:
 "d_inode() annotations from David Howells (sat in for-next since before
  the beginning of merge window) + four assorted fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  RCU pathwalk breakage when running into a symlink overmounting something
  fix I_DIO_WAKEUP definition
  direct-io: only inc/dec inode->i_dio_count for file systems
  fs/9p: fix readdir()
  VFS: assorted d_backing_inode() annotations
  VFS: fs/inode.c helpers: d_inode() annotations
  VFS: fs/cachefiles: d_backing_inode() annotations
  VFS: fs library helpers: d_inode() annotations
  VFS: assorted weird filesystems: d_inode() annotations
  VFS: normal filesystems (and lustre): d_inode() annotations
  VFS: security/: d_inode() annotations
  VFS: security/: d_backing_inode() annotations
  VFS: net/: d_inode() annotations
  VFS: net/unix: d_backing_inode() annotations
  VFS: kernel/: d_inode() annotations
  VFS: audit: d_backing_inode() annotations
  VFS: Fix up some ->d_inode accesses in the chelsio driver
  VFS: Cachefiles should perform fs modifications on the top layer only
  VFS: AF_UNIX sockets should call mknod on the top layer only

Pull more power management and ACPI updates from Rafael Wysocki:
 "These are fixes mostly (intel_pstate, ACPI core, ACPI EC driver,
  cpupower tool), a new CPU ID for the Intel RAPL driver and one
  intel_pstate driver improvement that didn't make it to my previous
  pull requests due to timing.

  Specifics:

   - Fix a build warning in the intel_pstate driver showing up in
     non-SMP builds (Borislav Petkov)

   - Change one of the intel_pstate's P-state selection parameters for
     Baytrail and Cherrytrail CPUs to significantly improve performance
     at the cost of a small increase in energy consumption (Kristen
     Carlson Accardi)

   - Fix a NULL pointer dereference in the ACPI EC driver due to an
     unsafe list walk in the query handler removal routine (Chris
     Bainbridge)

   - Get rid of a false-positive lockdep warning in the ACPI container
     hot-remove code (Rafael J Wysocki)

   - Prevent the ACPI device enumeration code from creating device
     objects of a wrong type in some cases (Rafael J Wysocki)

   - Add Skylake processors support to the Intel RAPL power capping
     driver (Brian Bian)

   - Drop the stale MAINTAINERS entry for the ACPI dock driver that is
     regarded as part of the ACPI core and maintained along with it now
     (Chao Yu)

   - Fix cpupower tool breakage caused by a library API change in libpci
     3.3.0 (Lucas Stach)"

* tag 'pm+acpi-4.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / scan: Add a scan handler for PRP0001
  ACPI / scan: Annotate physical_node_lock in acpi_scan_is_offline()
  ACPI / EC: fix NULL pointer dereference in acpi_ec_remove_query_handler()
  MAINTAINERS: remove maintainship entry of docking station driver
  powercap / RAPL: Add support for Intel Skylake processors
  cpufreq: intel_pstate: Fix an annoying !CONFIG_SMP warning
  intel_pstate: Change the setpoint for Atom params
  cpupower: fix breakage from libpci API change

Pull crypto fixes from Herbert Xu:
 "This push fixes a build problem with img-hash under non-standard
  configurations and a serious regression with sha512_ssse3 which can
  lead to boot failures"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: img-hash - CRYPTO_DEV_IMGTEC_HASH should depend on HAS_DMA
  crypto: x86/sha512_ssse3 - fixup for asm function prototype change

Merge tag 'platform-drivers-x86-v4.1-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform driver updates from Darren Hart:
 "This series includes significant updates to the toshiba_acpi driver
  and the reintroduction of the dell-laptop keyboard backlight additions
  I had to revert previously.  Also included are various fixes for
  typos, warnings, correctness, and minor bugs.

  Specifics:

  dell-laptop:
     - add support for keyboard backlight.

  toshiba_acpi:
     - adaptive keyboard, hotkey, USB sleep and charge, and backlight
       updates.  Update sysfs documentation.

  toshiba_bluetooth:
     - fix enabling/disabling loop on recent devices

  apple-gmux:
     - lock iGP IO to protect from vgaarb changes

  other:
     - Fix typos, clear gcc warnings, clarify pr_* messages, correct
       return types, update MAINTAINERS"

* tag 'platform-drivers-x86-v4.1-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (25 commits)
  toshiba_acpi: Do not register vendor backlight when acpi_video bl is available
  MAINTAINERS: Add me on list of Dell laptop drivers
  platform: x86: dell-laptop: Add support for keyboard backlight
  Documentation/ABI: Update sysfs-driver-toshiba_acpi entry
  toshiba_acpi: Fix pr_* messages from USB Sleep Functions
  toshiba_acpi: Update and fix USB Sleep and Charge modes
  wmi: Use bool function return values of true/false not 1/0
  toshiba_bluetooth: Fix enabling/disabling loop on recent devices
  toshiba_bluetooth: Clean up *_add function and disable BT device at removal
  toshiba_bluetooth: Add three new functions to the driver
  toshiba_acpi: Fix the enabling of the Special Functions
  toshiba_acpi: Use the Hotkey Event Type function for keymap choosing
  toshiba_acpi: Add Hotkey Event Type function and definitions
  x86/wmi: delete unused wmi_data_lock mutex causing gcc warning
  apple-gmux: lock iGP IO to protect from vgaarb changes
  MAINTAINERS: Add missing Toshiba devices and add myself as maintainer
  toshiba_acpi: Update events in toshiba_acpi_notify
  intel-oaktrail: Fix trivial typo in comment
  thinkpad_acpi: off by one in adaptive_keyboard_hotkey_notify_hotkey()
  thinkpad_acpi: signedness bugs getting current_mode
  ...

Pull chrome platform updates from Olof Johansson:
 "Here's a set of updates to the Chrome OS platform drivers for this
  merge window.

  Main new things this cycle is:

   - Driver changes to expose the lightbar to users.  With this, you can
     make your own blinkenlights on Chromebook Pixels.

   - Changes in the way that the atmel_mxt trackpads are probed.  The
     laptop driver is trying to be smart and not instantiate the devices
     that don't answer to probe.  For the trackpad that can come up in
     two modes (bootloader or regular), this gets complicated since the
     driver already knows how to handle the two modes including the
     actual addresses used.  So now the laptop driver needs to know more
     too, instantiating the regular address even if the bootloader one
     is the probe that passed.

   - mfd driver improvements by Javier Martines Canillas, and a few
     bugfixes from him, kbuild and myself"

* tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
  platform/chrome: chromeos_laptop - instantiate Atmel at primary address
  platform/chrome: cros_ec_lpc - Depend on X86 || COMPILE_TEST
  platform/chrome: cros_ec_lpc - Include linux/io.h header file
  platform/chrome: fix platform_no_drv_owner.cocci warnings
  platform/chrome: cros_ec_lightbar - fix duplicate const warning
  platform/chrome: cros_ec_dev - fix Unknown escape '%' warning
  platform/chrome: Expose Chrome OS Lightbar to users
  platform/chrome: Create sysfs attributes for the ChromeOS EC
  mfd: cros_ec: Instantiate ChromeOS EC character device
  platform/chrome: Add Chrome OS EC userspace device interface
  platform/chrome: Add cros_ec_lpc driver for x86 devices
  mfd: cros_ec: Add char dev and virtual dev pointers
  mfd: cros_ec: Use fixed size arrays to transfer data with the EC

Pull arch/cris updates from Jesper Nilsson:
 "Some much needed love for the CRIS-port.

  There's a bunch of changes this time, giving the CRISv32 port a bit of
  modern makeover with device-tree, irq domain and gpiolib support, and
  more switchover to generic frameworks.

  Some small fixes and removal of the theoretical SMP support brings up
  the rear"

* tag 'cris-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
  cris: fix integer overflow in ELF_ET_DYN_BASE
  CRISv32: use GENERIC_SCHED_CLOCK
  CRISv32: use MMIO clocksource
  CRISv32: use generic clockevents
  CRIS: use generic headers via Kbuild
  CRIS: use generic cmpxchg.h
  CRIS: use generic atomic.h
  CRIS: use generic atomic bitops
  CRISv10: remove redundant macros from system.h
  CRIS: remove SMP code
  CRISv32: don't enable irqs in INIT_THREAD
  CRISv32: handle multiple signals
  CRISv32: prevent bogus restarts on sigreturn
  CRISv32: don't attempt syscall restart on irq exit
  Add binding documentation for CRIS
  CRIS: add Axis 88 board device tree
  CRISv32: add device tree support
  CRISv32: add irq domains support
  CRIS: enable GPIOLIB

Pull powerpc fixes from Michael Ellerman:

 - fix for mm_dec_nr_pmds() from Scott.

 - fixes for oopses seen with KVM + THP from Aneesh.

 - build fixes from Aneesh & Shreyas.

* tag 'powerpc-4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
  powerpc/mm: Fix build error with CONFIG_PPC_TRANSACTIONAL_MEM disabled
  powerpc/kvm: Fix ppc64_defconfig + PPC_POWERNV=n build error
  powerpc/mm/thp: Return pte address if we find trans_splitting.
  powerpc/mm/thp: Make page table walk safe against thp split/collapse
  KVM: PPC: Remove page table walk helpers
  KVM: PPC: Use READ_ONCE when dereferencing pte_t pointer
  powerpc/hugetlb: Call mm_dec_nr_pmds() in hugetlb_free_pmd_range()

Commit 567e4b79 ("net: rfs: add hash collision detection") had one
mistake :

RPS_NO_CPU is no longer the marker for invalid cpu in set_rps_cpu()
and get_rps_cpu(), as @next_cpu was the result of an AND with
rps_cpu_mask

This bug showed up on a host with 72 cpus :
next_cpu was 0x7f, and the code was trying to access percpu data of an
non existent cpu.

In a follow up patch, we might get rid of compares against nr_cpu_ids,
if we init the tables with 0. This is silly to test for a very unlikely
condition that exists only shortly after table initialization, as
we got rid of rps_reset_sock_flow() and similar functions that were
writing this RPS_NO_CPU magic value at flow dismantle : When table is
old enough, it never contains this value anymore.

Fixes: 567e4b79 ("net: rfs: add hash collision detection")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for fixed-links in configurations without PHY.
(e.g. connection to a switch, SGMII point to point, SFPs)

Check: Documentation/devicetree/bindings/net/fixed-link.txt.
Signed-off-by: NAndreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull second batch of KVM changes from Paolo Bonzini:
 "This mostly includes the PPC changes for 4.1, which this time cover
  Book3S HV only (debugging aids, minor performance improvements and
  some cleanups).  But there are also bug fixes and small cleanups for
  ARM, x86 and s390.

  The task_migration_notifier revert and real fix is still pending
  review, but I'll send it as soon as possible after -rc1"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (29 commits)
  KVM: arm/arm64: check IRQ number on userland injection
  KVM: arm: irqfd: fix value returned by kvm_irq_map_gsi
  KVM: VMX: Preserve host CR4.MCE value while in guest mode.
  KVM: PPC: Book3S HV: Use msgsnd for signalling threads on POWER8
  KVM: PPC: Book3S HV: Translate kvmhv_commence_exit to C
  KVM: PPC: Book3S HV: Streamline guest entry and exit
  KVM: PPC: Book3S HV: Use bitmap of active threads rather than count
  KVM: PPC: Book3S HV: Use decrementer to wake napping threads
  KVM: PPC: Book3S HV: Don't wake thread with no vcpu on guest IPI
  KVM: PPC: Book3S HV: Get rid of vcore nap_count and n_woken
  KVM: PPC: Book3S HV: Move vcore preemption point up into kvmppc_run_vcpu
  KVM: PPC: Book3S HV: Minor cleanups
  KVM: PPC: Book3S HV: Simplify handling of VCPUs that need a VPA update
  KVM: PPC: Book3S HV: Accumulate timing information for real-mode code
  KVM: PPC: Book3S HV: Create debugfs file for each guest's HPT
  KVM: PPC: Book3S HV: Add ICP real mode counters
  KVM: PPC: Book3S HV: Move virtual mode ICP functions to real-mode
  KVM: PPC: Book3S HV: Convert ICS mutex lock to spin lock
  KVM: PPC: Book3S HV: Add guest->host real mode completion counters
  KVM: PPC: Book3S HV: Add helpers for lock/unlock hpte
  ...

Commit 43d3ddf8 ("net: pxa168_eth: add device tree support") starts
to use managed resources by adding devm_clk_get() and
devm_ioremap_resource(), but it leaves explicit iounmap() and clock_put()
in pxa168_eth_remove() and in failure handling code of pxa168_eth_probe().
As a result double free can happen.

The patch removes explicit resource deallocation. Also it converts
clk_disable() to clk_disable_unprepare() to make it symmetrical with
clk_prepare_enable().

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>