Hw DMA registers are written in rtl8180_init_hw function.
They are also written again just after calling rtl8180_init_hw.
There is no point in doing this twice.

Remove those redundant register writes from rtl8180_start.
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some Broadcom boards have more GPIOs available. For example Linksys
E3200 home router is based on SoC id 0x5357, package 0x0A and uses GPIO
23 to reset internal USB WiFi (gpio23=wombo_reset).
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

We should let user space request the peer address also in the pending
connect states, i.e. BT_CONNECT and BT_CONNECT2. There is existing user
space code that tries to do this and will fail without extending the set
of allowed states for the peer address information.

This patch adds the two states to the allowed ones in the L2CAP and
RFCOMM sock_getname functions, thereby preventing ENOTCONN from being
returned.
Reported-by: NAndrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Tested-by: NAndrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The smp variable in smp_conn_security is not used anywhere before the
smp = smp_chan_create() call in the smp_conn_security function so it
makes no sense to assign any other value to it before that.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The smp pointer might not be initialized for jumps to the "done" label
in the smp_conn_security function. Furthermore doing the set_bit after
done might "overwrite" a previous value of the flag in case pairing was
already in progress. This patch moves the call to set_bit before the
label so that it is only done for a newly created smp context (as
returned by smp_chan_create).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Due to several devices being unable to handle this procedure reliably
(resulting in forced disconnections before pairing completes) it's
better to remove it altogether.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In the case that the just-works model would be triggered we only want to
confirm remotely initiated pairings (i.e. those triggered by a Security
Request or Pairing Request). This patch adds the necessary check to the
tk_request function to fall back to the JUST_WORKS method in the case of
a locally initiated pairing.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

For remotely initiated just-works pairings we want to show the user a
confirmation dialog for the pairing. However, we can only know which
side was the initiator by tracking which side sends the first Security
Request or Pairing Request PDU. This patch adds a new SMP flag to
indicate whether our side was the initiator for the pairing.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In the case that a local pairing confirmation (JUST_CFM) has been
selected as the method we need to use the user confirm request mgmt
event for it with the confirm_hint set to 1 (to indicate confirmation
without any specific passkey value). Without this (if passkey_notify was
used) the pairing would never proceed. This patch adds the necessary
call to mgmt_user_confirm_request in this scenario.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

It is possible that the HCI_LE_Start_Encryption command fails in an
early stage and triggers a command status event with the failure code.
In such a case we need to properly notify the hci_conn object and
cleanly bring the connection down. This patch adds the missing command
status handler for this HCI command.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If a sudden disconnection happens the l2cap_conn pointer may already
have been cleaned up by the time hci_conn_security gets called,
resulting in the following oops if we don't have a proper NULL check:

BUG: unable to handle kernel NULL pointer dereference at 000000c8
IP: [<c132e2ed>] smp_conn_security+0x26/0x151
*pde = 00000000
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
CPU: 1 PID: 673 Comm: memcheck-x86-li Not tainted 3.14.0-rc2+ #437
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
task: f0ef0520 ti: f0d6a000 task.ti: f0d6a000
EIP: 0060:[<c132e2ed>] EFLAGS: 00010246 CPU: 1
EIP is at smp_conn_security+0x26/0x151
EAX: f0ec1770 EBX: f0ec1770 ECX: 00000002 EDX: 00000002
ESI: 00000002 EDI: 00000000 EBP: f0d6bdc0 ESP: f0d6bda0
 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 000000c8 CR3: 30f0f000 CR4: 00000690
Stack:
 f4f55000 00000002 f0d6bdcc c1097a2b c1319f40 f0ec1770 00000002 f0d6bdd0
 f0d6bde8 c1312a82 f0d6bdfc c1312a82 c1319f84 00000008 f4d81c20 f0e5fd86
 f0ec1770 f0d6bdfc f0d6be28 c131be3b c131bdc1 f0d25270 c131be3b 00000008
Call Trace:
 [<c1097a2b>] ? __kmalloc+0x118/0x128
 [<c1319f40>] ? mgmt_pending_add+0x49/0x9b
 [<c1312a82>] hci_conn_security+0x4a/0x1dd
 [<c1312a82>] ? hci_conn_security+0x4a/0x1dd
 [<c1319f84>] ? mgmt_pending_add+0x8d/0x9b
 [<c131be3b>] pair_device+0x1e1/0x206
 [<c131bdc1>] ? pair_device+0x167/0x206
 [<c131be3b>] ? pair_device+0x1e1/0x206
 [<c131ed44>] mgmt_control+0x275/0x2d6
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Make sure no timer callback is running before releasing the
datastructure which contains it.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The LE scan type paramter defines if active scanning or passive scanning
is in use. Track the currently set value so it can be used for decision
making from other pieces in the core.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

If vendor specific HCI commands are received from application,
we should send corresponding events to stack.
These events should be consumed in driver, only if they are for
the internal HCI commands generated by driver.

This patch fixes the vendor command 0x3f stuck problem with
above mentioned change. For example,

hcitool cmd 3f 22 fe 06 22 21 20 43 50 00
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We need to ensure that we do not send events to user space with the
identity address if we have not yet notified user space of the IRK. The
code was previously trying to handle this for the mgmt_pair_device
response (which worked well enough) but this is not the only connection
related event that might be sent to user space before pairing is
successful: another important event is Device Disconnected.

The issue can actually be solved more simply than the solution
previously used for mgmt_pair_device. Since we do have the identity
address tracked as part of the remote IRK struct we can just copy it
over from there to the hci_conn struct once we've for real sent the mgmt
event for the new IRK.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In order to support the driver behaviour introduced by:

   commit d0575a5a703978c43e25128421158c78534ba100
   Author: Daniel Kim <dekim@broadcom.com>
   Date:   Wed Mar 12 18:12:14 2014 -0700

       brcmfmac: Enable 40MHz bandwidth in 2GHz band and OBSS scanning

in devices that do not support bwcap firmware command a fallback
is added.
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the function brcmf_sdiod_request_data() an error message is logged,
but the calling function retries it. This patch will only log an error
message when retry limit is reached. The low-level error is still
logged by a SDIO debug message.
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The watchdog thread waits on completion that is set from a timer. As
the completion is count based this could mean that on a busy system
the watchdog is handled multiple times with a very short interval.
This is not the intended behaviour. After handling the watchdog it
should wait for the next timer expiry. This is accomplished by
reinitializing the completion.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch enables 40MHz bandwidth in 2GHz band after checking whether
cfg80211 allows it or not, and enables OBSS scanning operations to
to support 20/40 BSS coexistence.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NDaniel Kim <dekim@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

The passkey_notify and user_confirm functions in mgmt.c were expecting
different endianess for the passkey, leading to a big endian bug and
sparse warning in recently added SMP code. This patch converts both
functions to expect host endianess and do the conversion to little
endian only when assigning to the mgmt event struct.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In Secure Connections Only mode, it is required that Secure Connections
is used for pairing and that the link key is encrypted with AES-CCM using
a P-256 authenticated combination key. If this is not the case, then new
connection shall be refused or existing connections shall be dropped.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

It is possible that pairing fails after we've already received remote
identity information. One example of such a situation is when
re-encryption using the LTK fails. In this case the hci_conn object has
already been updated with the identity address but user space does not
yet know about it (since we didn't notify it of the new IRK yet).

To ensure user space doesn't get a Pair Device command response with an
unknown address always use the same address in the response as was used
for the original command.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When performing SMP pairing with MITM protection one side needs to
enter the passkey while the other side displays to the user what needs
to be entered. Nowhere in the SMP specification does it say that the
displaying side needs to any kind of confirmation of the passkey, even
though a code comment in smp.c implies this.

This patch removes the misleading comment and converts the code to use
the passkey notification mgmt event instead of the passkey confirmation
mgmt event.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In some cases the current 250ms delay is not enough for the remote to
receive the keys, as can be witnessed by the following log:

> ACL Data RX: Handle 64 flags 0x02 dlen 21               [hci1] 231.414217
      SMP: Signing Information (0x0a) len 16
        Signature key: 555bb66b7ab3abc9d5c287c97fe6eb29
< ACL Data TX: Handle 64 flags 0x00 dlen 21               [hci1] 231.414414
      SMP: Encryption Information (0x06) len 16
        Long term key: 2a7cdc233c9a4b1f3ed31dd9843fea29
< ACL Data TX: Handle 64 flags 0x00 dlen 15               [hci1] 231.414466
      SMP: Master Identification (0x07) len 10
        EDIV: 0xeccc
        Rand: 0x322e0ef50bd9308a
< ACL Data TX: Handle 64 flags 0x00 dlen 21               [hci1] 231.414505
      SMP: Signing Information (0x0a) len 16
        Signature key: bbda1b2076e2325aa66fbcdd5388f745
> HCI Event: Number of Completed Packets (0x13) plen 5    [hci1] 231.483130
        Num handles: 1
        Handle: 64
        Count: 2
< HCI Command: LE Start Encryption (0x08|0x0019) plen 28  [hci1] 231.664211
        Handle: 64
        Random number: 0x5052ad2b75fed54b
        Encrypted diversifier: 0xb7c2
        Long term key: a336ede66711b49a84bde9b41426692e
> HCI Event: Command Status (0x0f) plen 4                 [hci1] 231.666937
      LE Start Encryption (0x08|0x0019) ncmd 1
        Status: Success (0x00)
> HCI Event: Number of Completed Packets (0x13) plen 5    [hci1] 231.712646
        Num handles: 1
        Handle: 64
        Count: 1
> HCI Event: Disconnect Complete (0x05) plen 4            [hci1] 232.562587
        Status: Success (0x00)
        Handle: 64
        Reason: Remote User Terminated Connection (0x13)

As can be seen, the last key (Signing Information) is sent at 231.414505
but the completed packets event for it comes only at 231.712646,
i.e. roughly 298ms later.

To have a better margin of error this patch increases the delay to
500ms.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This is a trivial coding style simplification by instead of having an
extra early return to instead revert the if condition and do the single
needed queue_work() call there.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Macro ASSERT_RDEV_LOCK(rdev) is equal to ASSERT_RTNL(), so replace it
with ASSERT_RTNL() and remove it.
Signed-off-by: NZhao, Gang <gamerh2o@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

RCU pointer bss->pub.beacon_ies is checked before in previous
statement:

if (rcu_access_pointer(bss->pub.beacon_ies))
	continue;

There is no need to check it twice(and in the wrong way :) ).
Signed-off-by: NZhao, Gang <gamerh2o@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add a bit in rx_status.vht_flags to let the low level driver
notify mac80211 about a beamformed packet. Propagate this
to the radiotap header.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

On 2.4Ghz band, the channels overlap since the delta
between different channels is 5Mhz while the width of the
receiver is 20Mhz (at least).

This means that we can hear beacons or probe responses from
adjacent channels. These frames will have a significant
lower RSSI which will feed all kinds of logic with inaccurate
data. An obvious example is the roaming algorithm that will
think our AP is getting weak and will try to move to another
AP.

In order to avoid this, update the signal only if the frame
has been heard on the same channel as the one advertised by
the AP in its DS / HT IEs.
We refrain from updating the values only if the AP is
already in the BSS list so that we will still have a valid
(but inaccurate) value if the AP was heard on an adjacent
channel only.

To achieve this, stop taking the channel from DS / HT IEs
in mac80211. The DS / HT IEs is taken into account to
discard the frame if it was received on a disabled channel.
This can happen due to the same phenomenon: the frame is
sent on channel 12, but heard on channel 11 while channel
12 can be disabled on certain devices. Since this check
is done in cfg80211, stop even checking this in mac80211.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove unused rx_freq variable]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Function __cfg80211_join_ibss() is only used in net/wireless/ibss.c,
so make it static.
Signed-off-by: NZhao, Gang <gamerh2o@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Drivers might want to have private data in addition
to all other ieee80211_tx_info.status fields.

The current ieee80211_tx_info.rate_driver_data overlaps
with some of the non-rate data (e.g. ampdu_ack_len), so
it might not be good enough.

Since we already know how much free bytes remained,
simply use this size to define (void *) array.

While on it, change ack_signal type from int to the more
explicit s32 type.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Assuming sched_scan_stop operation is synchronous the driver may not
necessary call ieee80211_sched_scan_stopped_work. Since this work is
the only place where sched_scan_sdata is released we can possibly run
into situation when it is never released. Fix this by releasing it
just after calling drv_sched_scan_stop.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

commit de74a1d9
  "mac80211: fix WPA with VLAN on AP side with ps-sta"
fixed an issue where queued multicast packets would
be sent out encrypted with the key of an other bss.

commit "7cbf9d01"
  "mac80211: fix oops on mesh PS broadcast forwarding"
essentially reverted it, because vif.type cannot be AP_VLAN
due to the check to vif.type in ieee80211_get_buffered_bc before.

As the later commit intended to fix the MESH case, fix it
by checking for IFTYPE_AP instead of IFTYPE_AP_VLAN.

Cc: stable@vger.kernel.org
Fixes: 7cbf9d01 ("mac80211: fix oops on mesh PS broadcast forwarding")
Signed-off-by: NMichael Braun <michael-dev@fami-braun.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In the 802.11ad, aka DMG (Dynamic Multi-Gigabit), aka 60Ghz
spec, maximum MSDU size extended to 7920 bytes.
add #define for this.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since Stanislaw's patch removing the quiescing code, mac80211 had
a race regarding suspend vs. authentication: as cfg80211 doesn't
track authentication attempts, it can't abort them. Therefore the
attempts may be kept running while suspending, which can lead to
all kinds of issues, in at least some cases causing an error in
iwlmvm firmware.

Fix this by aborting the authentication attempt when suspending.

Cc: stable@vger.kernel.org
Fixes: 12e7f517 ("mac80211: cleanup generic suspend/resume procedures")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When still authenticating the mac80211 code handling a deauthentication
requests from userspace doesn't verify that the request is valid in any
way, fix that. Additionally, it never returns an error, even if there's
no connection or authentication attempt, fix that as well.

While at it, move the message to not print a message in the error case
and to distinguish between the two cases.

Also simplify the code by duplicating the cfg80211 call.
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The bss struct might be freed in ieee80211_rx_bss_put(),
so we shouldn't use it afterwards.

Cc: stable@vger.kernel.org (3.10+)
Fixes: 817cee76 ("mac80211: track AP's beacon rate and give it to the driver")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>