Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 27 7月, 2005 1 次提交
  3. 26 6月, 2005 2 次提交
  5. 24 6月, 2005 3 次提交
    • D
      [PATCH] Keys: Make request-key create an authorisation key · 3e30148c
      由 David Howells 提交于 
      The attached patch makes the following changes:

 (1) There's a new special key type called ".request_key_auth".

     This is an authorisation key for when one process requests a key and
     another process is started to construct it. This type of key cannot be
     created by the user; nor can it be requested by kernel services.

     Authorisation keys hold two references:

     (a) Each refers to a key being constructed. When the key being
     	 constructed is instantiated the authorisation key is revoked,
     	 rendering it of no further use.

     (b) The "authorising process". This is either:

     	 (i) the process that called request_key(), or:

     	 (ii) if the process that called request_key() itself had an
     	      authorisation key in its session keyring, then the authorising
     	      process referred to by that authorisation key will also be
     	      referred to by the new authorisation key.

	 This means that the process that initiated a chain of key requests
	 will authorise the lot of them, and will, by default, wind up with
	 the keys obtained from them in its keyrings.

 (2) request_key() creates an authorisation key which is then passed to
     /sbin/request-key in as part of a new session keyring.

 (3) When request_key() is searching for a key to hand back to the caller, if
     it comes across an authorisation key in the session keyring of the
     calling process, it will also search the keyrings of the process
     specified therein and it will use the specified process's credentials
     (fsuid, fsgid, groups) to do that rather than the calling process's
     credentials.

     This allows a process started by /sbin/request-key to find keys belonging
     to the authorising process.

 (4) A key can be read, even if the process executing KEYCTL_READ doesn't have
     direct read or search permission if that key is contained within the
     keyrings of a process specified by an authorisation key found within the
     calling process's session keyring, and is searchable using the
     credentials of the authorising process.

     This allows a process started by /sbin/request-key to read keys belonging
     to the authorising process.

 (5) The magic KEY_SPEC_*_KEYRING key IDs when passed to KEYCTL_INSTANTIATE or
     KEYCTL_NEGATE will specify a keyring of the authorising process, rather
     than the process doing the instantiation.

 (6) One of the process keyrings can be nominated as the default to which
     request_key() should attach new keys if not otherwise specified. This is
     done with KEYCTL_SET_REQKEY_KEYRING and one of the KEY_REQKEY_DEFL_*
     constants. The current setting can also be read using this call.

 (7) request_key() is partially interruptible. If it is waiting for another
     process to finish constructing a key, it can be interrupted. This permits
     a request-key cycle to be broken without recourse to rebooting.
Signed-Off-By: NDavid Howells <dhowells@redhat.com>
Signed-Off-By: NBenoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      3e30148c
    • C
      [PATCH] Optimize sys_times for a single thread process · 71a2224d
      由 Christoph Lameter 提交于 
      Avoid taking the tasklist_lock in sys_times if the process is single
threaded.  In a NUMA system taking the tasklist_lock may cause a bouncing
cacheline if multiple independent processes continually call sys_times to
measure their performance.
Signed-off-by: NChristoph Lameter <christoph@lameter.com>
Signed-off-by: NShai Fultheim <shai@scalex86.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      71a2224d
    • A
      [PATCH] setuid core dump · d6e71144
      由 Alan Cox 提交于 
      Add a new `suid_dumpable' sysctl:

This value can be used to query and set the core dump mode for setuid
or otherwise protected/tainted binaries. The modes are

0 - (default) - traditional behaviour.  Any process which has changed
    privilege levels or is execute only will not be dumped

1 - (debug) - all processes dump core when possible.  The core dump is
    owned by the current user and no security is applied.  This is intended
    for system debugging situations only.  Ptrace is unchecked.

2 - (suidsafe) - any binary which normally would not be dumped is dumped
    readable by root only.  This allows the end user to remove such a dump but
    not access it directly.  For security reasons core dumps in this mode will
    not overwrite one another or other files.  This mode is appropriate when
    adminstrators are attempting to debug problems in a normal environment.

(akpm:

> > +EXPORT_SYMBOL(suid_dumpable);
>
> EXPORT_SYMBOL_GPL?

No problem to me.

> >  	if (current->euid == current->uid && current->egid == current->gid)
> >  		current->mm->dumpable = 1;
>
> Should this be SUID_DUMP_USER?

Actually the feedback I had from last time was that the SUID_ defines
should go because its clearer to follow the numbers. They can go
everywhere (and there are lots of places where dumpable is tested/used
as a bool in untouched code)

> Maybe this should be renamed to `dump_policy' or something.  Doing that
> would help us catch any code which isn't using the #defines, too.

Fair comment. The patch was designed to be easy to maintain for Red Hat
rather than for merging. Changing that field would create a gigantic
diff because it is used all over the place.

)
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      d6e71144
  7. 06 5月, 2005 1 次提交
  9. 01 5月, 2005 3 次提交
  11. 17 4月, 2005 1 次提交
    • L
      Linux-2.6.12-rc2 · 1da177e4
      由 Linus Torvalds 提交于 
      Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
      1da177e4