Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 04 10月, 2005 4 次提交
    • A
      libata: bitmask based pci init functions for one or two ports · 47a86593
      由 Alan Cox 提交于 
      This redoes the n_ports logic I proposed before as a bitmask.
ata_pci_init_native_mode is now used with a mask allowing for mixed mode
stuff later on. ata_pci_init_legacy_port is called with port number and
does one port now not two. Instead it is called twice by the ata init
logic which cleans both of them up.

There are stil limits in the original code left over

- IRQ/port mapping for legacy mode should be arch specific values
- You can have one legacy mode IDE adapter per PCI root bridge on some systems
- Doesn't handle mixed mode devices yet (but is now a lot closer to it)
      47a86593
    • T
      [PATCH] libata: add ATA exceptions chapter to doc · fe998aa7
      由 Tejun Heo 提交于 
       Hello, Jeff.

This patch adds ATA errors & exceptions chapter to
Documentation/DocBook/libata.tmpl.  As suggested, the chapter is
placed before low level driver specific chapters.  Contents are
unchanged from the last posting.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
      fe998aa7
    • B
      [PATCH] libata: Marvell SATA support (DMA mode) (resend: v0.22) · 31961943
      由 Brett Russ 提交于 
      This is my libata compatible low level driver for the Marvell SATA
family.  Currently it runs in DMA mode on a 6081 chip.

The 5xxx series parts are not yet DMA capable in this driver because
the registers have differences that haven't been accounted for yet.
Basically, I'm focused on the 6xxx series right now.  I apologize for
those seeing problems on the 5xxx series, I've not had a chance to
look at those problems yet.

For those curious, the previous bug causing the SCSI timeout and
subsequent panics was caused by an improper clear of hc_irq_cause in
mv_host_intr().

This version is running well in my environment (6081 chips,
with/without SW raid1) and is showing equal or better performance
compared to the Marvell driver (mv_sata) in my initial tests (timed
dd's of reads/writes to/from memory/disk).

I still need to look at the causes of occasional problems such as this:

ata11: translating stat 0x35 err 0x00 to sense
ata11: status=0x35 { DeviceFault SeekComplete CorrectedError Error }
SCSI error : <10 0 0 0> return code = 0x8000002
Current sda: sense key Hardware Error
end_request: I/O error, dev sda, sector 3155010

and this, seen at init time:

ATA: abnormal status 0x80 on port 0xE093911C

but they aren't showstoppers.
Signed-off-by: NBrett Russ <russb@emc.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
      31961943
    • J
      Merge branch 'master' · 2b235826
      由 Jeff Garzik 提交于
      2b235826
  3. 03 10月, 2005 6 次提交
  5. 02 10月, 2005 8 次提交
  7. 01 10月, 2005 22 次提交