Split zoom2 board file into a base board file and a board-zoom-peripherals.c
file. That way the same peripherals file can be reused for zoom3 and sdp3630
in addition to zoom2.

Also remove unused struct omap_board_config_kernel entry.

NOTE: Keep the twl4030_madc_platform_data and twl4030_platform_data
entries in board-zoom2.c to avoid merge conflicts with the pending
patches in MFD tree. These entries will be removed later as a fix.

Following list shows the commonality across the three platforms and hence the
case for software reuse:

Peripheral    zoom2    zoom3  sdp3630
---------------------------------------
Ethernet        smsc    smsc    smc
NOR             n/a     n/a     B
Onenand         n/a     n/a     B
HDMI            A       A       B (present on different i2c)
NAND            A       A       A (same nand)
SDRAM           A       A       A (same sdram)
Keypad          A       A       A (same twl)
Camera          A       A       A (same sensor can be mounted)
LCD Display     A       A       A (same wvga display)
OPPs            A       A       A (same chip feature)
Audio           A       A       A (same audio via twl5030)
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Migrate to smsc911x ethernet driver instead of smc911x driver.
The smsc911x ethernet driver supports NAPI and performs better
under heavy traffic. With the smc911x driver we were witnessing
very high iowait time for high IO load over NFS.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Initialize vmmc and vmmc_aux regulators

Note that the omap3evm_twldata.vmmc1 and omap3evm_twldata.vsim
are set in omap3_evm_i2c_init() to avoid a merge conflict
with the MFD tree. These will be initialized in omap3evm_i2c_boardinfo
as a fix later on.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Added runtime programming for the differences in EHCI interface between
OMAP3EVM revisions (Rev >= E) and (Rev < E).

Changes:
	- EHCI PHY reset GPIO pin is 21 on Rev >= E while Rev < E
	  uses GPIO pin 135.
	- Rev >= E uses EHCI Vbus enable GPIO22 line.
	- Rev >= E uses GPIO61 to select EHCI port either on main board or
	  on Mistral Daughter Card (MDC). OMAP3EVM Rev < E doesn't have
	  EHCI port on main board.
	- Currently GPIO61 it programmed to enable EHCI port on main
	  board only.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>

Added function to differentiate between the OMAP3EVM revisions. The
chip-id of the ethernet PHY is being used for this purpose.

Rev A to D : 0x01150000
Rev >= E   : 0x92200000
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Cleanup the coding style in id.c while avoiding unneeded switch()
statements.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds code changes in the mailbox driver module to
add support for OMAP4 mailbox.
Signed-off-by: NHari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: NC A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: NRamesh Gupta G <grgupta@ti.com>
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds resource information of mailbox driver for
OMAP4 mailbox module. Register base address also added
Signed-off-by: NC A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: NRamesh Gupta G <grgupta@ti.com>
Acked-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds changes to the build related files of mailbox
driver
Signed-off-by: NC A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: NRamesh Gupta G <grgupta@ti.com>
Acked-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

When listing the various SoC features, print them on the same line.
So, instead of this

OMAP3430/3530 ES3.1
 - l2cache : Y
 - iva : Y
 - sgx : Y
 - neon : Y
 - isp : Y

you get this:

OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

omap3_check_revision() does not depend on omap3_check_features()
move this above so that we can add logic based on revision
detected in check_features.
Signed-off-by: NNishanth Menon <nm@ti.com>
Acked-by: NMika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for omap hsmmc2 8-bit mux configuration.
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The speed ctrl bit for MMC I/O is part of CONTROL_PROG_IO1 register
in omap3630.This patch sets it up accordingly.
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The HSMMC1 controller on omap3630 supprts only 4-bit mode. If cpu
is 3630 configure HSMMC1 wires to 4-bit.
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Change the cpu_is_omap3430() check to cpu_is_omap34xx() to allow HSMMC1/2
mux configuration for omap3630.
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This way it's more object oriented and easier to see what is happening.
No functional changes.
Signed-off-by: NFelipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform init code for EHCI driver.

Various fixes to the original patch by Ajay Kumar Gupta <ajay.gupta@ti.com>
and Anand Gadiyar <gadiyar@ti.com>.

Overo support added by Olof Johansson <olof@lixom.net>
Beagle support added by Koen Kooi <koen@beagleboard.org>
CM-T32 support added by Mike Rapoport <mike@compulab.co.il>
Signed-off-by: NSigned-off-by: Olof Johansson <olof@lixom.net>
Acked-by: NSteve Sakoman <steve@sakoman.com>
Signed-off-by: NKoen Kooi <koen@beagleboard.org>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

AM35xx is functionally similar to OMAP3430 ES3.1 from a
powerdomain/clockdomain perspective. This patch initializes the
omap_chip bits on AM35xx for use by powerdomain and clockdomain code.
Signed-off-by: NRanjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support to detect AM3505/AM3517 devices at runtime.
Also updates the CPU names printed during boot.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

3630 is getting treated like next rev of 3430
omap_chip.oc variable has to be updated for 3630 version

Otherwise the Core power domain is not getting registered.

This gets used in the registration of power domains in:
"arch/arm/mach-omap2/powerdomains34xx.h"
core_34xx_es3_1_pwrdm
OMAP_CHIP_INIT(CHIP_GE_OMAP3430ES3_1)

Core power doman will get registered for 3630 only when .oc is
populated correctly.

Tested on Zoom3(3630) board
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Acked-by: NAlexander Shishkin <virtuoso@slind.org>
Acked-by: NAri Kauppi <kauppi@papupata.org>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP3630 is the latest in the family of OMAP3 devices
and among the changes it introduces are:

New OPP levels for new voltage and frequency levels. a bunch of
Bug fixes to various modules feature additions, notably with ISP,
sDMA etc.

Details about the chip is available here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12836&contentId=52606

Strategy used:
Strategy to introduce this device into Linux was discussed here:
Ref: http://marc.info/?t=125343303400003&r=1&w=2

Two approaches were available:
a) Consider 3630 generation of devices as a new family of silicon
b) Consider 3630 as an offshoot of 3430 family of devices

As a common consensus, (b) seems to be more valid for 3630 as:
* There are changes which are easily handled by using "FEATURES"
  infrastructure.
  For details how to do this, see thread:
  http://marc.info/?t=125050998500001&r=1&w=2
* Most of existing 34xx infrastructure can be reused(almost 90%+)
	- so no ugly if (cpu_is_omap34xx() || cpu_is_omap36xx())
	  all over the place
	- lesser chance of bugs due to reuse of proven code flow
	- 36xx specific handling can still be done where required
	  within the existing infrastructure

NOTE:
* If additional 34xx series are added, OMAP3430_REV_ESXXXX can be
  added on top of the existing 3630 ones are renumbered

This patch was tested on SDP3430, boot tested on 3630 platform using
3430sdp defconfig
Signed-off-by: NMadhusudhan Chikkature Rajashekar <madhu.cr@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Cc: Allen Pais <allen.pais@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Sanjeev Premi <premi@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Sergio Alberto Aguirre Rodriguez <saaguirre@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add runtime check for these OMAP35x variations
based on the detected Si features:
  OMAP3503, OMAP3515, OMAP3525 and OMA3530.

Also, delayed the call to pr_info() into actual
variant is detected in omap3_cpuinfo()
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The OMAP35x family has multiple variants differing
in the HW features. This patch detects these features
at runtime and prints information during the boot.

Since most of the code seemed repetitive, macros
have been used for readability.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Eliminate OMAP_MAX_NR_PORTS

Note that also the null terminator entry for omap1
serial_platform_data needs to be now removed to avoid
oopsing.

Note that mach-omap1 uses struct plat_serial8250_port
array, which requires a null terminator at the end,
and that's why we need to use ARRAY_SIZE - 1. This
is not needed on mach-omap2 as the array used is
struct omap_uart_state, and does not use a null
terminator.
Signed-off-by: NAlexander Shishkin <virtuoso@slind.org>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Initialize some of the RX-51 input GPIO lines as gpio keys. Enable gpio
keys as a module in rx51_defconfig.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

audio_mclk value is going to be handled by the
twl4030-codec MFD driver, configure the correct
value for boards, which is using the twl4030 audio.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add needed platform data for the twl4030_codec MFD on boards,
where the audio part of the twl4030 codec is used.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The index `cs' is signed, test whether it is negative before we release
gpmc_cs_mem[cs].
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

Current calculation does not take into account any changes to M2 divisor, and
thus when we change VDD2 OPP, dpll3_m2x2 rate does not change. Fixed by
re-routing dpll3_m2x2 parent to dpll3_m2.
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix the freqsel value computation. Use n instead of (n+1)

The formula in the TRM uses a zero-based N, hence the (n+1); however
at this point in the clock34xx.c code, N is one-based.

Hayati Bayrakdar <h-bayrakdar@ti.com> and Nishanth Menon <nm@ti.com> helped
track down this bug.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
[paul@pwsan.com: modified commit message]
Cc: Hayati Bayrakdar <h-bayrakdar@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Interpretation of 'row' and 'col' got reversed in matrix keymap
framework. Also last element '0', present in keymap array, is no
more needed.
Correcting zoom2 keyboard keymap accordingly.
Signed-off-by: NVimal Singh <vimalsingh@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fixes a bug where scheduling is delayed until next wakeup due to race
condition (e.g. interrupt requests scheduling just before omap_sram_idle
is entered.)
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch removes the check to see if some functional clocks are
still enabled before entering sleep.  This is no longer needed when
using safe state (C1) that keeps CORE active.
Signed-off-by: NPeter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

It is more efficient to use pwrdm_set_next_pwrst for mpu, core and neon
instead of set_pwrdm_state in idle loop. It is anyway known that those are
active in idle loop. So no need to use set_pwrdm_state.
Signed-off-by: NJouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The current definition of C-states starts from base 1.
Whereas, the cpuidle driver uses base 0. This patch
eliminates need for explicit mapping (add/ sbutract)
due to different base values.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch introduces a new C state which allows MPU to go to WFI but keeps
the core domain active. This offers a much better wakeup latency (3us vs
10s of us for the current C1) at the cost of a higher power consumption.
Signed-off-by: NPeter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Previously omap3_idle_init() was called in device_init, while
omap_pm_init() is called at late_initcall. This causes the cpu idle
driver to call omap_sram_idle before it is properly initialized. This
patch fixes the issue by moving omap3_idle_init into omap3_pm_init.
Signed-off-by: NKalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Use the activity check for states C2 and C3 as well.  This is
primarily to prevent deeper states during UART activity.

Also, if a different state is chosen than the target state, update the
'last_state' accordingly so that CPUidle state accounting is coorect.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

If 'enable_off_mode' is not set, force powerdomain states to RET
instead of OFF.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds support and enables state C4(MPU RET + CORE RET)
and MPU OFF states (C3 and C5.)
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>