liteBoard is a development board which uses liteSOM as its base.

Hardware specification:
 * liteSOM (i.MX6UL, DRAM, eMMC)
 * Ethernet PHY (id 0)
 * USB host (usb_otg1)
 * MicroSD slot (uSDHC1)
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This is a SOM (System on Module), so it will be part of another boards.
Hence, this is a "dtsi" file that will be included from another device
tree files.

Hardware specification:
 * Freescale i.MX6UL SoC
 * up to 512 MB RAM
 * eMMC on uSDHC2
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Enable PWM1, otherwise the backlight cannot work.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add initial device trees for UDOO Neo Basic, Extended and Full boards:
* Serial console is enabled, other serial ports are prepared.
* I2C based PMIC is enabled.
* Ethernet is enabled for Basic and Full.
* SDHC is enabled, with the SDIO_PWR GPIO modeled as a regulator.
* Both user LEDs are enabled, with the orange one reserved for the M4
  and with the SD card as default trigger for the red LED.

The decision on a board compatible string is deferred to later.

Cc: Ettore Chimenti <ettore.chimenti@udoo.org>
Signed-off-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Also add nodes and properties for thermal management support.
Signed-off-by: NJia Hongtao <hongtao.jia@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Enable DMA for DSPI on Vybrid.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The LCDIF interrupt should be triggered by the rising edge of the
IRQ line because we only want the interrupt to trigger once per each
frame. It seems the LCDIF IRQ line cannot be explicitly de-asserted
by software, so the previous behavior before this patch, where the
interrupt was triggered by level-high status of the IRQ line, caused
the interrupt to fire again immediatelly after it was handled, which
caused the system to lock up due to the high rate of interrupts.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add node corresponding to OCOTP IP block.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

I2C3 bus was only brought out in revision A1 of the board and revision
B1 only brings out 3 I2C busses (I2C0, I2C1 and I2C2).
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Fixed error in trailing whitespace in wandboard-rev1 dtsi.
Signed-off-by: NJagan Teki <jteki@openedev.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Fixed code indent tabs in respetcive imx6qdl dtsi files.
Signed-off-by: NJagan Teki <jteki@openedev.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Fixed no space before tabs warnings in respetcive imx6qdl dtsi files.
Signed-off-by: NJagan Teki <jteki@openedev.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Calibrate the USB PHY TX settings to pass the eye diagram signal
integrity test.  The settings are taken from the i.MX6 reference
manual's recommended configuration for USB certification (66.2.6).
Signed-off-by: NJaret Cantu <jaret.cantu@timesys.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Use enable-gpios property of PWM backlight driver for backlight
control.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Remove use of pwm-leds and use the standard /sys/class/pwm
interface from PWM subsystem.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
Acked-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add support for Toradex Colibri iMX6 module.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
Acked-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The change adds a new device node with description of generic SRAM
on-chip memory found on NXP LPC32xx SoC series and connected to AHB
matrix slave port 3.

Note that NXP LPC3220 SoC has 128KiB of SRAM memory, the other
LPC3230, LPC3240 and LPC3250 SoCs all have 256KiB SRAM space,
in the shared DTSI file this change specifies 128KiB SRAM size.

Also it's worth to mention that the SRAM area contains of 64KiB banks,
2 banks on LPC3220 and 4 banks on the other SoCs from the series, and
all SRAM banks but the first one have independent power controls,
the description of this feature will be added with the introduction of
power domains for the SoC series.
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch fixes the following DTC warning with W=1:

"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

This patch fixes the following DTC warning with W=1:

"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

This patch fixes the following DTC warning with W=1:

"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

This patch fixes the following DTC warning with W=1:

"Node /soc has a reg or ranges property, but no unit name"
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

This patch fixes the following DTC warning with W=1:

"Node /soc has a reg or ranges property, but no unit name"
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

This patch fixes the following DTC warning with W=1:

"Node /soc has a reg or ranges property, but no unit name"
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

As noted in [1], "there are a number of problems with skeleton.dtsi,
and it would be prefereable to remove it entirely." This patch is to
remove skeleton.dtsi inclusion from berlin2.

[1] http://www.spinics.net/lists/arm-kernel/msg528080.htmlSigned-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

As noted in [1], "there are a number of problems with skeleton.dtsi,
and it would be prefereable to remove it entirely." This patch is to
remove skeleton.dtsi inclusion from berlin2cd.

[1] http://www.spinics.net/lists/arm-kernel/msg528080.htmlSigned-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

As noted in [1], "there are a number of problems with skeleton.dtsi,
and it would be prefereable to remove it entirely." This patch is to
remove skeleton.dtsi inclusion from berlin2q.

[1] http://www.spinics.net/lists/arm-kernel/msg528080.htmlSigned-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

After commit f29a72c2 ("watchdog: dw_wdt: Convert to use watchdog
infrastructure"), the dw_wdt driver can support multiple variants, so
unconditionally enable all dw_wdt nodes now.
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

After commit f29a72c2 ("watchdog: dw_wdt: Convert to use watchdog
infrastructure"), the dw_wdt driver can support multiple variants, so
unconditionally enable all dw_wdt nodes now.
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

Enable throttle function for SOC_THERM.
Set "hot" trips for cpu and gpu thermal zones, which
can trigger the SOC_THERM hardware throttle.
Signed-off-by: NWei Ni <wni@nvidia.com>
Signed-off-by: NZhang Rui <rui.zhang@intel.com>

Set general "critical" trip temperatures for cpu, gpu, mem and pllx
thermal zones for all Tegra124 platform, these trips can trigger
shut down or reset.
Tegra124 Jetson TK1 was already set "critical" trips before, so it
can overwrite the general values.
Signed-off-by: NWei Ni <wni@nvidia.com>
Signed-off-by: NZhang Rui <rui.zhang@intel.com>

Use the new sun7i-a20-mmc compatible for the mmc controllers on sun7i
and newer.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Originally-from: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: NAlexandre TORGUE <alexandre.torgue@st.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: arnd@arndb.de
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: bruherrera@gmail.com
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: lee.jones@linaro.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1474387259-18926-5-git-send-email-alexandre.torgue@st.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Add a dt node describing the mma7660 accelerometer on the
polaroid-mid2407pxe03 tablet.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

UART1 is connected to the bluetooth part of RTL8723BS WiFi/BT combo card
on iNet D978 Rev2 board.

Enable the UART1 to make it possible to use the modified hciattach by
Realtek to drive the BT part of RTL8723BS.

On the board no r_uart pins are found now (the onboard RX/TX pins are
wired to PF2/PF4, which is muxed with mmc0), so also disabled it.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The UART1 at PG (PG6, PG7, PG8, PG9) is, in the Allwinner's reference
tablet design of A23/33, used to connect to UART Bluetooth cards.

Add the pinmux for it.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

These peripherals can only be muxed to these pins, so they are
associated in the DTSI instead of the board files. This makes it very
easy to enable them using overlays or u-boot commands:

 => fdt set /soc/i2c@01c2ac00 status okay
Signed-off-by: NJorik Jonker <jorik@kippendief.biz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

These are the only possible pins for these peripherals according to the
datasheet.
Signed-off-by: NJorik Jonker <jorik@kippendief.biz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

These H3 boards all expose UART1-3 on their expansion header. Since
other functions can be muxed to these pins, they are explicitly
disabled. To enable them, one could use DT overlays or U-boot commands:

 => fdt set /soc/serial@01c28c00 status okay
Signed-off-by: NJorik Jonker <jorik@kippendief.biz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This was done to make UART1-3 on H3 consistent, and less complicated to
enable UART1-3 on the breakout header on the several H3 board (notably
Orange Pi's). This patch adds a bit of complexity for the existing Banana
Pi, which already had the RTS/CTS associated on UART1.

The RTS/CTS for UART2-3 could be defined in the same way, but since
there is no actual use case for them at the moment, they are left out.
Signed-off-by: NJorik Jonker <jorik@kippendief.biz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

These are the pinmux definitions for UART2-3 on H3. These UARTs can only
be muxed to these pins, so _a and @0 do not really make sense. I have
left out RTS/CTS, since these are rarely used. These can easily be
enabled using an additional pinmux set.
Signed-off-by: NJorik Jonker <jorik@kippendief.biz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>