Add configuration for connection monitor (number of allowed beacons, and
timeout after last received beacon.)
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

At least two revisions of the D-Link DWA 160 exist, called A1 and A2. A1
(USB-ID 07d1:3c10) is already listed in usb.c as D-Link DWA 160A. A2
(USB-ID 07d1:3a09) works if added to ar9170_usb_ids. I didn't do much
testing until now, but I was able to connect to APs using WPA or WEP and
transmit data.

Summary:

* Add model revision number to the comment for D-Link DWA 160 A1 (07d1:3c10)
* Add support for D-Link DWA 160 A2 (07d1:3a09)
Signed-off-by: NThomas Klute <thomas2.klute@uni-dortmund.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

taken from windows inf file (09/15/2009, 1.04.07.0000)
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The netdev broadcast address cannot change from
all-ones so there's no need to use it; we can
instead hard-code it. Since we already have an
instance in tkip.c, which will be shared if it
is marked static const, doing this reduces text
size at no data/bss cost.

The real motivation for this is, of course, the
desire to get rid of almost all uses of netdevs
in mac80211 so that auditing their use becomes
easier.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we move the rcu sections a little, there's
no need to touch the device refcount.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some code currently assumes that there's a valid
rate pointer even in the HT case, but there can't
be. To reduce reliance on that, remove the rate
pointer from the RX data struct and pass it where
it's needed.

Also, for now, in radiotap announce HT frames as
having a DYN channel type, and remove their rate
from cooked monitor radiotap completely (it isn't
present in the regular monitor radiotap either.)
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The RX data contains the netdev, which is
duplicated since we have the sdata, and the
RX status pointer, which is duplicate since
we have the skb. Remove those two fields to
have fewer fields that depend on each other
and simply load them as necessary.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The reorder buffer handling is written in a quite
peculiar style (especially comments) and also has
a quirk where it invokes the entire reorder code
in ieee80211_sta_manage_reorder_buf() for just a
handful of lines in it with a special argument.

Split out ieee80211_release_reorder_frames which
can then be invoked from BAR handling and other
reordering code, clean up code and comments and
remove function arguments that are now unused from
ieee80211_sta_manage_reorder_buf().
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we receive a michael MIC failure report from the
hardware we currently do not check whether it is actually
reported on a frame that is destined to us. It shouldn't
be possible to get a michael MIC failure report on other
frames, but it also doesn't hurt to verify.

Also, since we then don't need the station struct that
early, move looking it up a bit later in the RX path.

Finally, while at it, a few code cleanups in the area.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The entire aggregation code currently operates on the
hw pointer and station addresses, but that needs to
change to make stations purely per-vif; As one step
preparing for that make the aggregation code callable
with the station, or by the combination of virtual
interface and station address.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of filtering by device, directly look up by sdata.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check for AR5416 ver 1.0 before calibrating 3 chains
for multi-chain. This is a WAR for calibration
failure.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ATH9K_ANT_VARIABLE is the default diversity control used.
Consequently ath9k_hw_decrease_chain_power() does nothing.
ath9k_hw_setantennaswitch() is unused too.

Also, gbeacon_rate is unused.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

axq_linkbuf, axq_aggr_depth, axq_lastdsWithCTS and
axq_gatingds are unused.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Remove a code chunk dealing with operating mode changes.
  As noted, all such policy changes are to be done in
  add_interface.

* Remove pointless check for empty BSSID.
  Also, remove mode checks - mac80211 does all the needed checks.

* Handle enabling/disabling beacon transmission properly.

* Handle beacon interval changes for AP mode.
  The original code depended on config_interface() to update
  the HW TSF. Since that callback has been removed, handle
  it properly.

* Remove unneeded code dealing with key/privacy.

* Set the chainmasks to 1x1 for IBSS when the BSSID is set.
  This was happening uncondionally before.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes the need for separately allocated private tx info
data in ath9k and brings the driver one small step closer to using the
mac80211 rate control API properly.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to handle association and authentication in AP mode,
hostapd needs access to the tx status info of its own frames
through a cooked monitor interface. Without this patch the
cooked monitor interfaces also passed on tx status information
for packets from other virtual interfaces. This creates a
significant performance issue on embedded system. Hostapd
tries to work around this by installing a Linux Socket Filter
that only captures the frames it's interested in, however
data duplication and socket filter matching still uses up
enough CPU cycles to be very noticeable on small systems.
This patch ensures that tx status information of non-injected
frames does not make it to cooked monitor interfaces.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch enables the driver to process all incoming
dupofdm-modulated frames when operating in HT40 mode.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also regroup CSR_EEPROM and CSR_OTP bit field definitions.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using the new mac80211 functionality, this makes
iwlwifi handle unicast PS buffering correctly.
The device works like this:

 * when a station goes to sleep, the microcode notices
   this and marks the station as asleep
 * when the station is marked asleep, the microcode
   refuses to transmit to the station and rejects all
   frames queued to it with the failure status code
   TX_STATUS_FAIL_DEST_PS (a previous patch handled
   this correctly)
 * when we need to send frames to the station _although_
   it is asleep, we need to tell the ucode how many,
   and this is asynchronous with sending so we cannot
   just send the frames, we need to wait for all other
   frames to be flushed, and then update the counter
   before sending out the poll response frames. This
   is handled partially in the driver and partially in
   mac80211.

In order to do all this correctly, we need to
 * keep track of how many frames are pending for each
   associated client station (avoid doing it for other
   stations to avoid the atomic ops)
 * tell mac80211 that we driver-block the PS status
   while there are still frames pending on the queues,
   and once they are all rejected (due to the dest sta
   being in PS) unblock mac80211
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This field was marked as reserved before since we didn't
use it, but is present in all released firmwares afaict.
We're going to need it soon, so add it now.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a frame is sent to a sleeping station, the
microcode reports TX_STATUS_FAIL_DEST_PS as its
status -- we need to translate that to the flag
that mac80211 expects.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Handle BSS_CHANGED_BEACON_ENABLED to enable the sending
of beacons. Also set the correct HT RXON and QoS config.
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When sending beacon commands to the uCode, we must
inform it of the offset in the beacon frame of the
TIM Element so it can transmit packets from the
correct queue. This functionality is implemented
in iwl_set_beacon_tim().

Fix a bug setting the rate_n_flags for the beacon
packet. First, it should not use the station table's
rate (it's a management frame), and second it needs
to properly configure the TX antennas.

Finally, also, clean up and comment relevant functions.
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A recent change optimized the power usage by the device by only powering it
up during EEPROM load if it is required (for OTP devices). This change causes
an error on the 1000 series devices during module load.

The error looks as follows:
[ 1624.024524] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds
[ 1624.024527] iwlagn: Copyright(c) 2003-2009 Intel Corporation
[ 1624.024711] iwlagn 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1624.024749] iwlagn 0000:01:00.0: setting latency timer to 64
[ 1624.024909] iwlagn 0000:01:00.0: Detected Intel Wireless WiFi Link 1000 Series BGN REV=0x6C
[ 1624.081263] iwlagn 0000:01:00.0: MAC is in deep sleep!.  CSR_GP_CNTRL = 0x080003D8
[ 1624.092967] iwlagn 0000:01:00.0: OTP is empty
[ 1624.092988] iwlagn 0000:01:00.0: Unable to init EEPROM
[ 1624.093033] iwlagn 0000:01:00.0: PCI INT A disabled
[ 1624.093065] iwlagn: probe of 0000:01:00.0 failed with error -2

Adding a dump_stack() to where that error is printed shows the following:

[ 1624.024524] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds
[ 1624.024527] iwlagn: Copyright(c) 2003-2009 Intel Corporation
[ 1624.024711] iwlagn 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1624.024749] iwlagn 0000:01:00.0: setting latency timer to 64
[ 1624.024909] iwlagn 0000:01:00.0: Detected Intel Wireless WiFi Link 1000 Series BGN REV=0x6C
[ 1624.081263] iwlagn 0000:01:00.0: MAC is in deep sleep!.  CSR_GP_CNTRL = 0x080003D8
[ 1624.081263] Pid: 3073, comm: work_for_cpu Tainted: G        W 2.6.31.5 #4
[ 1624.081263] Call Trace:
[ 1624.081263]  [<ffffffffa02395db>] T.726+0x22b/0x420 [iwlcore]
[ 1624.081263]  [<ffffffffa023985a>] iwlcore_eeprom_acquire_semaphore+0x8a/0x190 [iwlcore]
[ 1624.081263]  [<ffffffff81110c94>] ? __kmalloc+0x194/0x1c0
[ 1624.081263]  [<ffffffffa02391f5>] ?  iwlcore_eeprom_verify_signature+0x25/0xf0 [iwlcore]
[ 1624.081263]  [<ffffffffa0239c67>] iwl_eeprom_init+0x107/0xf40 [iwlcore]
[ 1624.081263]  [<ffffffffa026ab9c>] ?  iwl_prepare_card_hw+0x11c/0x470 [iwlagn]
[ 1624.081263]  [<ffffffff8127e2a4>] ?  pci_bus_write_config_byte+0x64/0x80
[ 1624.081263]  [<ffffffffa026b1f8>] iwl_pci_probe+0x308/0xac0 [iwlagn]
[ 1624.081263]  [<ffffffff810710a0>] ? do_work_for_cpu+0x0/0x30
[ 1624.081263]  [<ffffffff81284912>] local_pci_probe+0x12/0x20
[ 1624.081263]  [<ffffffff810710b3>] do_work_for_cpu+0x13/0x30
[ 1624.081263]  [<ffffffff81075826>] kthread+0xa6/0xb0
[ 1624.081263]  [<ffffffff81012fea>] child_rip+0xa/0x20
[ 1624.081263]  [<ffffffff81075780>] ? kthread+0x0/0xb0
[ 1624.081263]  [<ffffffff81012fe0>] ? child_rip+0x0/0x20
[ 1624.092967] iwlagn 0000:01:00.0: OTP is empty
[ 1624.092988] iwlagn 0000:01:00.0: Unable to init EEPROM
[ 1624.093033] iwlagn 0000:01:00.0: PCI INT A disabled
[ 1624.093065] iwlagn: probe of 0000:01:00.0 failed with error -2

We know that the routines in this trace, iwlcore_eeprom_acquire_semaphore
and iwlcore_eeprom_verify_signature, only access CSR registers and thus do
not need the device to be awake if it is EEPROM. But for OTP it is required
for the device to be awake to read these registers. Ensure device is awake
before accessing these registers.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Acked-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Align the format for tx_statistics and rx_statistics debugfs output for
better readability
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In both 6x00 and 6x50 series, the enhanced/extended tx power table in
EEPROM is used to set the max. tx power limit.
This new tx power table is in 1/2 dBm format, which creates an issue of
possibility of 1/2 dBm loss when driver set the tx power limit; because
of driver keep track and report the tx power in dBm format.

In order to prevent the 1/2 dBm loss, keep track of the true max tx
power in 1/2 dBm format in driver; do the comparison and adjust the tx
power if needed when send tx power command to uCode.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Power-saving logic will not re-issue a POWER_TABLE_CMD if a new command
matches the prior one.  This can be bad if we re-start the device due to
e.g. uCode error; the new POWER_TABLE_CMD (required to invoke power-saving)
may match the prior POWER_TABLE_CMD issued before the uCode error.

Ensure the POWER_TABLE_CMD is sent to device when uCode is up.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When issue REPLY_STATISTICS_CMD to uCode, two possible flag
can be set in the configuration flags

bit 0: Clear statistics
       0: Do not clear Statistics counters
       1: Clear to zero Statistics counters

Allow "clear" parameter to be set from the caller.

Add debugfs file to clear the statistics counters to help monitor and
debug the uCode behavior.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Number of data structure for 6000 series no longer in production, the
data structure already being removed; also need to remove the external
reference define in iwl-dev.h
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drop the non-production PCI-IDs for 6x50 series
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Number of HT40 power parameters are not used; remove those from
iwl_channel_info data structure
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Temporary disable the coex function for wifi/wimax for 6x50
series until the full implementation ready.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Validate enhanced tx power entry read from EEPROM before applying the
tx power value. Different versions of EEPROM might contain different size
of table; always a good idea to make sure the entry is valid before
applying to the targeted channel.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In this file, function names are otherwise used as pointers without &.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier f;
@@

f(...) { ... }

@@
identifier r.f;
@@

- &f
+ f
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this file, function names are otherwise used as pointers without &.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier f;
@@

f(...) { ... }

@@
identifier r.f;
@@

- &f
+ f
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this file, function names are otherwise used as pointers without &.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier f;
@@

f(...) { ... }

@@
identifier r.f;
@@

- &f
+ f
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this file, function names are otherwise used as pointers without &.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier f;
@@

f(...) { ... }

@@
identifier r.f;
@@

- &f
+ f
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>