* Set AR5K_DCU_GBL_IFS_MISC_TURBO_MODE flag on DCU when operating
 on 40MHz
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Replace set_slot_time with set_ifs_intervals that also sets
 the various inter-frame space intervals based on current bwmode.

 * Clean up AR5210 mess from reset_tx_queue, AR5210 only has one
 data queue and we set IFS intervals for that queue on set_ifs_intervals
 so there is nothing left to do for 5210 on reset_tx_queue.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Extend get_default_sifs/slot_time to include timings for turbo
 half and quarter rate modes.

 * AR5210 code for now uses timings already on core clock units
 instead of usecs so rename them (we 'll clean it up later).
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Move setting of tx retry limits on a separate function
 (we 'll clean up this AR5210 mess later)
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * On turbo mode increase PHY settling times, note that
 we only increase switch settling time on AR5212 as indicated
 by initvals.

 * A few cleanups: Move frame control settings for AR5210 from
 reset_tx_queue to tweak_initvals and remove phy_scal settings
 from tweak_initvals (we tweak them alread on set_sleep_clock).
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Handle all usec parameters in one function. It's much cleaner
 this way.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Prepare for half/quarter/turbo support, introduce a new
 ah_bwmode parameter and get rid of ah_turbo. Bwmode stands
 for "bandwidth mode" and can have 4 values, default (20MHz),
 turbo (40MHz), half rate (10MHz), and quarter rate (5MHz).
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * DCU early termination should be used to quickly flush QCU
 according to docs so don't enable it for all queues, enable
 it only when stopping each queue and disable it when we are
 done.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * No functional changes

 * Clean up reset:
 Introduce init functions for each unit and call them instead
 of having everything inside ath5k_hw_reset (it's just c/p for
 now so nothing changes except calling order -I tested it with
 various cards and it's ok-)

 * Further cleanups:
 ofdm_timings belongs to phy.c
 rate_duration belongs to pcu.c
 clock functions are general and belong to reset.c (more to follow)

 * Reorder functions for better organization:
 We start with helpers and other functions follow in categories,
 init functions are last
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Get rid of overly complicated cw_min/max and AIFS configuration:

* Validate values in ath5k_hw_set_tx_queueprops(), so we can use them directly
  without further checks or computation in ath5k_hw_reset_tx_queue().

* Simplifiy by using AR5K_TUNE_AIFS|CWMIN|CWMAX variables directly since we
  don't support XR or B channels. That way we can also remove
  AR5K_TXQ_USEDEFAULT and the confusing logic around it.

* Update data types: AIFS is u8, CW's are u16.

* Remove now unneeded variables in ath5k_hw.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that we have ftrace, it is not needed any more.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"ath5k: remove stale function declarations, make some functions static"
commented-out some unused functions.  This removes them.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NBob Copeland <me@bobcopeland.com>

Remove all unnecessary function declarations from ath5k.h.  Comment out
unused functions.  Remove ath5k_hw_get_tsf32(), which is too trivial to
be commented out.  Make functions static if suggested by sparse.  Make
ath5k_pm_ops static.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The beacon sent gating doesn't seem to work with any combination
of flags.  Thus, buffered frames tend to stay buffered forever,
using up tx descriptors.

Instead, use the DBA gating and hold transmission of the buffered
frames until 80% of the beacon interval has elapsed using the ready
time.  This fixes the following error in AP mode:

   ath5k phy0: no further txbuf available, dropping packet

Add a comment to acknowledge that this isn't the best solution.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The original code was correct in 802.11a mode only, 802.11b/g uses
different clock rates. The new code uses values taken from FreeBSD HAL
and should be correct for all modes including turbo modes.

The former rate calculation was used by slope coefficient calculation
function ath5k_hw_write_ofdm_timings. However, this function requires
the 802.11a values even in 802.11g mode. Thus the use of
ath5k_hw_htoclock was replaced by hardcoded values. Possibly the slope
coefficient calculation is not related to clock rate at all.
Signed-off-by: NLukas Turek <8an@praha12.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Functions ath5k_hw_get_slot_time and ath5k_hw_set_slot_time were
converting microseconds to clocks only for AR5210, although it's needed
for all supported devices. The conversion was moved outside the
hardware-specific branches.

The original code also limited minimum slot time to 9, while turbo modes
use 6, this was fixed too.
Signed-off-by: NLukas Turek <8an@praha12.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Elsewhere, the tqi_type field is compared to constants having a name
beginning with AR5K_TX_QUEUE, rather than AR5K_TX_QUEUE_ID.  I have thus
converted AR5K_TX_QUEUE_ID_CAB to AR5K_TX_QUEUE_CAB.  This does, however,
change the value, so perhaps something else was wanted.
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable the "Content" After Beacon queue and utilize it to send
any buffered frames for power-saving clients.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Write next beacon timer even on AP mode since without this we get
 no beacons + ath9k does it too.  Docs say that we must write 0 on
 this register on AP mode to start TSF increment, we do both to be
 on the safe side.

 * Fix num_tx_pending function, we never read the register :P that's
 why we got all those "beacon queue 7 didn't stop messages".

 * Put full prioriy on beacon queue, lock all queues with lower
 priority using the arblock and also bypass any arblock by seting
 the arblock ignore flag.

 * For the CAB queue (do we need this thing ?, it seems crap) since
 it's supposed to fire up after each beacon (we don't use it on driver
 part, ath9k/MadWiFi does), don't make it DBA gated but instead make
 it fire after each beacon by using the beacon sent gated flag.

 * Increase bmiss threshold to 10, that's what we used on MadWiFi for
 a long time. Also when we have pending frames on the beacon queue (we
 got a beacon that didn't make it on the air) it's more likely that
 the beacon queue never started, probably due to faulty DBA setting,
 so change that "beacon queue didn't stop" message.

 Tested this with AP mode and IBSS mode and seems to work fine ;-)
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Sync qcu.c with legacy-hal
* Add some more comments
* Set QCU mask to save power (QCU mask controls which QCUs are attached
  to each DCU, we do a 1:1 mapping)

TODO: Use max QCU from EEPROM, further sync with legacy-hal and sam's
hal and a few more minor fixes.

I think after this we are ready to implement WME on the driver
part. Anyone interested ?
Signed-Off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

*Properly get/set all available ISR/IMR values and review common/uncommon bits
*Better handling of per-txq interrupts (we can now resolve what q is generating
 each interrupt -this will help in debuging wme later)
*Some minor updates from legacy-hal
*Properly handle RXNOFRM and TXNOFRM interrupt masking (even when we don't set
 them on IMR they keep showing up, so we disable them by zeroing AR5K_RXNOFRM
 and AR5K_TXNOFRM registers). This doesn't exist on legacy-hal but i've tested
 it on various cards and it works fine.

Changes-Licensed-under: ISC
Signed-Off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Update registers
 * Update SREV values and add some PHY srevs
 * Prepare ath5k.h for newer radios etc

 Thanks to Atheros 's HAL source we now know for sure how many parts we have
 and what their SREV values are. We also have some updates on registers. Prepare
 ath5k for some major updates ;-)

 My previous mail had 2 more patches following (git log misusage), sorry for double
 posting ;-(

Changes-Licensed-under: ISC
Signed-Off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * No code changes...

 * Split hw.c to multiple files for better maintenance and add some documentation on each file
   code is going to grow soon (eeprom.c for example is going to get much stuff currently developed
   on ath_info) so it's better this way.

 * Rename following functions to maintain naming scheme:

     ah_setup_xtx_desc -> ah_setup_mrr_tx_desc
     (Because xtx doesn't say much, it's actually
     a multi-rate-retry tx descriptor)

     ath5k_hw_put_tx/rx_buf - > ath5k_hw_set_tx/rxdp
     ath5k_hw_get_tx/rx_buf -> ath5k_hw_get_tx/rxdp
     (We don't put any "buf" we set descriptor pointers on hw)

     ath5k_hw_tx_start -> ath5k_hw_start_tx_dma
     ath5k_hw_start_rx -> ath5k_hw_start_rx_dma
     ath5k_hw_stop_pcu_recv -> ath5k_hw_stop_rx_pcu
     (It's easier this way to identify them, we also
     have ath5k_hw_start_rx_pcu which completes the
     set)

     ath5k_hw_set_intr -> ath5k_hw_set_imr
     (As in get_isr we set imr here, not "intr")

  * Move ath5k_hw_setup_rx_desc on ah->ah_setup_rx_desc so we can
    include support for different rx descriptors in the future

  * Further cleanups so that checkpatch doesn't complain
    (only some > 80 col warnings for eeprom.h and reg.h as usual
    due to comments)

  Tested on 5211 and 5213 cards and works ok.

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>