while (timeout--) { ... }

timeout becomes -1 if the loop isn't ended otherwise, not 0.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this the 2nd port gets first ports MAC addr.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using sgmii the link was not being properly passed up to the driver
from the underlying link management functions.  This change corrects it so
that get_link_status is cleared when a link has been found.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A panic has been observed with frame sizes smaller than 1K.  This has been
root caused to the hardware spanning larger frames across multiple buffers
and then reporting the original frame size in the first descriptor.  To
prevent this we can enable set the LPE bit which in turn will restrict
packet sizes to those set in the RLPML register.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

82576 was being incorrectly flagged as needing a context index.  It does not as
each ring has it's own table of 2 contexts.

Driver was registering after registering the driver instead of the other way around.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we use a spin-lock to serialise statistics fetches and also
to inhibit them for short periods of time, plus a flag to
enable/disable statistics fetches for longer periods of time, during
online reset.  This was apparently insufficient to deal with the several
reasons for stats being disabled.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All 10Xpress PHYs require autonegotiation all the time; enforce this
in the set_settings() method and do not treat it as a workaround.

Remove claimed support for 100M HD mode since it is not supported by
current firmware.

Do not set speed override bits when AN is enabled, and do not use
register 1.49192 for AN configuration as it can override what we set
elsewhere.

Always set the AN selector bits to 1 (802.3).

Fix confusion between Next Page and Extended Next Page.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This workaround is not specific to rev A.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Depending on the loopback mode, there may be no pertinent link state
bits.  In this case we test the PHYXS RX fault bit instead.  Make
sure to do this in all cases where there are no link state bits.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In particular, set pause advertising bits properly.

A PHY reset is not necessary to recover from the register self-test,
so use a "invisible" reset there instead.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify falcon_switch_mac() to always set NIC_STAT_REG, even if the the
MAC is the same as it was before.  This ensures that the value is
correct after an online reset.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change sfn4111t_reset() to change only GPIO output enables so that it
doesn't break subsequent I2C operations.

Update comments to explain exactly what we're doing.

Add a short sleep to make sure the FLASH_CFG_1 value is latched before
any subsequent I2C operations.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of disabling AN in loopback, just prevent restarting AN and
override the speed in sft9001_get_settings().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Early versions of the SFX7101 firmware could complete link training in
a state where it would not adequately cancel noise (Solarflare bug
10750).  We previously worked around this by resetting the PHY after
seeing many Ethernet CRC errors.  This workaround is unsafe since it
takes no account of the interval between errors; it also appears to
be unnecessary with production firmware.  Therefore remove it.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable a firmware option that appears to be necessary for reliable
operation.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Printing anything over netconsole before hw is up and running is,
of course, not going to work.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

with current kernels, tulip 21142 ethernet controllers fail to connect
to a 10Mbps only (i.e. without negotiation-partner) network.  It used
to work in 2.4 kernels.  Fix that.  Tested on a 21142 Rev 0x11.
Signed-off-by: NPhilippe De Muyter <phdm@macqel.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix inverted logic
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 0f0ca340 ("phy: power
management support") caused a regression in the gianfar driver.

Now phylib turns off PHY power during suspend, and thus WOL
doesn't work anymore.

This patch workarounds the issue by enabling wakeup in the MDIO
device, i.e. just restores the old behaviour for the gianfar
driver. Note that this way all PHYs on a given MDIO bus won't
be turned off during suspend, which isn't good from the power
saving point of view.

A proper, per netdevice wakeup management support will need
a bit reworked phylib suspend/resume logic.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With a postfix decrement the timeout will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smsc9420 performs an interrupt signalling test when the interface is
brought up.  The current code mistakenly sets its test flag to false
AFTER enabling the software interrupt source, making failure quite
likely.

This patch changes the code to set the test flag BEFORE enabling
interrupts. I've also removed an smp_wmb because the following spinlock
provides an implicit memory barrier.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit b31a1d8b ("gianfar: Convert
gianfar to an of_platform_driver") changes the gianfar's phy id to the
format like "mdio@xxxx:xx", but uec still uses the old format like
"xxxxxxxx:xx".  For the board whose UEC uses gianfar-mdio like
MPC8568MDS, the phy can not be attached because of the incompatible
phy id format. This patch changes uec's phy id to the same format as
gianfar's.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Toralf Förster and Randy Dunlap.

- http://linuxwimax.org/pipermail/wimax/2009-January/000460.html

- http://lkml.org/lkml/2009/1/29/279

The definitions needed for the wimax stack and i2400m driver debug
infrastructure was, by mistake, compiled depending on CONFIG_DEBUG_FS
(by them being placed in the debugfs.c files); thus the build broke in
2.6.29-rc3 when debugging was enabled (CONFIG_WIMAX_DEBUG) and
DEBUG_FS was disabled.

These definitions are always needed if debug is enabled at compile
time (independently of DEBUG_FS being or not enabled), so moving them
to a file that is always compiled fixes the issue.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For kernel bugzilla #12537:
http://bugzilla.kernel.org/show_bug.cgi?id=12537

Free memory.
Signed-off-by: NDaniel Marjamäki <danielm77@spray.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reducing jumbo ring size below 1024 reduces throughput for old
firmwares (3.4.216 and older) running on older (NX2031) chip,
so restore it back to 1024.

This was reduced in commit 32ec8033
("netxen: reduce memory footprint").

Raising jumbo ring size from 512 to 1024, adds ~4MB per port, but
there's still big saving because of original patch (~20MB per port).
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ath5k_config updates the software context without taking sc->lock.

Changes-licensed-under: 3-Clause-BSD
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch fixes memcpy to NULL address when the ucode DMA allocation failure.

This is a fix to bug
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1861Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After reports of poor performance, a review of the latest vendor driver
(rtl8187_linux_26.1025.0328.2007) for RTL8187L devices was undertaken.

A difference was found in the code used to index the OFDM power tables. When
the Linux driver was changed, my unit works at a much greater range than
before. I think this fixes Bugzilla #12380 and has been tested by at least
two other users.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NMartín Ernesto Barreyro <barreyromartin@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A nasty bug was found where an MTU change (or anything else that caused a
reset) could race with the interrupt code.  The interrupt code was entered
by a shared interrupt during the MTU change.

This change prevents the interrupt code from running while the driver is in
the middle of its reset path.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/r6040.c:441: warning: unused variable 'pdev'
Signed-off-by: NManish Katiyar <mkatiyar@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this fix, virtio_net makes incorrect usage of scatterlists. It sets
the end of the scatterlist chain after the first element, despite the fact
that more entries come after it.

If you try to run dma_map_sg() on one of the scatterlists given to you by
add_buf(), you will get a null pointer oops.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 77ecaf2d ("gianfar: Fix VLAN
HW feature related frame/buffer size calculation") wrongly removed
priv->vlgrp assignment, and now priv->vlgrp is always NULL.

This patch fixes the issue, plus fixes following sparse warning
introduced by the same commit:
gianfar.c:1406:13: warning: context imbalance in 'gfar_vlan_rx_register' - wrong count at exit

gfar_vlan_rx_register() checks for "if (old_grp == grp)" and tries
to return w/o dropping the lock.

According to net/8021q/vlan.c VLAN core issues rx_register() callback:
1. In register_vlan_dev() only on a newly created group;
2. In unregister_vlan_dev() only if the group becomes empty.

Thus the check in the gianfar driver isn't needed.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current tx_has_work waited until all packets sent by the driver
are marked as completed by the FW. This is too greedy and it causes
the bnx2x_poll to spin in vain. The driver should only check that all
packets FW already completed are freed - only in unload flow the
driver should make sure that transmit queue is empty
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o reduce rx ring size from 8192 to 4096.
o cut down old huge lro buffers.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o set netdev->vlan_features appropriately.
o fix tso descriptor initialization for vlan case.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following patch fixes a warning caused by a missing ifdef in
isdn_ppp.c. A function was defined, but never used if CONFIG_IPPP_FILTER
was not defined.

The warning was: 'get_filter' defined but not used
Patch is against 2.6.28.1
Signed-off-by: NDaniele Venzano <venza@brownhat.org>
Acked-by: NKarsten Keil <kkeil@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that all EEPROM drivers live in the same place, let's harmonize
their symbol names.

Also fix eeprom's dependencies, it definitely needs sysfs, and is no
longer experimental after many years in the kernel tree.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>