Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Fix the following errors and warnings:

ERROR: trailing whitespace
ERROR: spaces required around that '=' (ctx:VxV)
WARNING: please, no space before tabs
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Moves the Solarflare drivers into drivers/net/ethernet/sfc/ and
make the necessary Kconfig and Makefile changes.

CC: Steve Hodgson <shodgson@solarflare.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

We only have direct access to SPI on Falcon, so move all this state
out of struct efx_nic.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In new NICs flash is managed by firmware and we will use high-level
operations on partitions rather than direct SPI commands.  Add support
for multiple MTD partitions per flash device and remove the direct
link between MTD and SPI devices.  Maintain a list of MTD partitions
in struct efx_nic.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make falcon_spi_wait() ignore the write timer - it is only relevant to
write commands, it only works for the device that contains VPD, and it
might not be initialised properly at all.

Rename falcon_spi_fast_wait() to falcon_spi_wait_write(), reflecting
its use, and make it wait up to 10 ms (not 1 ms) since buffered writes
to EEPROM may take this long to complete.

Make both wait functions sleep instead of busy-waiting.

Replace wait for command completion at top of falcon_spi_cmd() with a
single poll; no command should be running when the function starts.

Correct some comments.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on a patch by Andrew Morton.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The boot code that appears as a PCI expansion ROM on the SFC4000 is
stored in flash.  Expose this as a standard MTD device to allow for
in-place upgrades.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Move flash and EEPROM partition boundary constants into spi.h and rename
them to be consistent.

Add a comment on the partitioning.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Extend the SPI device setup code to support this.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The driver supports the 10Xpress PHY and XFP modules on our reference
designs SFE4001 and SFE4002 and the SMC models SMC10GPCIe-XFP and
SMC10GPCIe-10BT.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>