Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

A few of these were found and reported by Lothar Waßmann.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

A variable named "dev" usually (usually subjective) points to a struct
device.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

This undoes the effects of phy_start in fec_enet_open.
Reported-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Moreover stop listing all i.MX platforms featuring a FEC, and use
the platform's config symbol that selects registration of a fec device
instead.  This might make it easier to add new platforms.

Set default = y for ARMs having a fec to reduce defconfig sizes.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Saving it first into struct net_device->base_addr (which is an unsigned
long) is pointless and only needs to use more casts than necessary.
Reported-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

alloc_etherdev internally uses kzalloc, so the private data is already
zerod out.
Reported-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

dev_set_drvdata is called unconditionally in the probe function and so
it cannot be NULL.
Reported-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Reported-by: NLothar Waßmann <LW@KARO-elektronics.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Reported-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

memcpy takes a const void * as 2nd argument.  So the argument is
converted automatically to void * anyhow.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

This patch is to add mx28 dual fec support. Here are some key notes
for mx28 fec controller.

 - The mx28 fec controller naming ENET-MAC is a different IP from FEC
   used on other i.mx variants.  But they are basically compatible
   on software interface, so it's possible to share the same driver.
 - ENET-MAC design on mx28 made an improper assumption that it runs
   on a big-endian system. As the result, driver has to swap every
   frame going to and coming from the controller.
 - The external phys can only be configured by fec0, which means fec1
   can not work independently and both phys need to be configured by
   mii_bus attached on fec0.
 - ENET-MAC reset will get mac address registers reset too.
 - ENET-MAC MII/RMII mode and 10M/100M speed are configured
   differently FEC.
 - ETHER_EN bit must be set to get ENET-MAC interrupt work.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following commit made a fix to use fec_enet_open/fec_enet_close
over fec_enet_init/fec_stop for suspend/resume, because fec_enet_init
does not allow to have a working network interface at resume.

  e3fe8558
  net/fec: fix pm to survive to suspend/resume

This fix works for i.mx/mxc fec controller, but fails on mx28 fec
which gets a different interrupt logic design. On i.mx fec, interrupt
can be triggered even bit ETHER_EN of ECR register is not set. But
on mx28 fec, ETHER_EN must be set to get interrupt work. Meanwhile,
MII interrupt is mandatory to resume the driver, because MDIO
read/write changed to interrupt mode by commit below.

  97b72e43
  fec: use interrupt for MDIO completion indication

fec_restart/fec_stop comes out as the solution working for both
cases.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add mac field into fec_platform_data and consolidate function
fec_get_mac to get mac address in following order.

 1) module parameter via kernel command line fec.macaddr=0x00,0x04,...
 2) from flash in case of CONFIG_M5272 or fec_platform_data mac
    field for others, which typically have mac stored in fuse
 3) fec mac address registers set by bootloader
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "index" becomes legacy since fep->pdev->id starts working
to identify the instance.

Moreover, the call of fec_enet_init(ndev, 0) always passes 0
to fep->index. This makes the following code in fec_get_mac buggy.

	/* Adjust MAC if using default MAC address */
	if (iap == fec_mac_default)
		dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index;

It may be the time to remove "index" and use fep->pdev->id instead.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FEC_MMFR_OP_WRITE should be used than FEC_MMFR_OP_READ in
a mdio write operation.

It's probably a typo introduced by commit:

e6b043d5
netdev/fec.c: add phylib supporting to enable carrier detection (v2)
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At least one board using the FEC driver does not have a conventional
PHY attached to it, it is directly connected to a somewhat simple
ethernet switch (the board is the SnapGear/LITE, and the attached
4-port ethernet switch is a RealTek RTL8305). This switch does not
present the usual register interface of a PHY, it presents nothing.
So a PHY scan will find nothing - it finds ID's of 0 for each PHY
on the attached MII bus.

After the FEC driver was changed to use phylib for supporting PHYs
it no longer works on this particular board/switch setup.

Add code support to use a fixed phy if no PHY is found on the MII bus.
This is based on the way the cpmac.c driver solved this same problem.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

with hardware slow in negotiation, the system did freeze
while trying to mount root on nfs at boot time.

the link state has not been initialised so network stack
tried to start transmission right away. this caused instant
retries, as the driver solely stated business upon link down,
rendering the system unusable.

notify carrier off initially to prevent transmission until
phylib will report link up.
Signed-off-by: NOskar Schirmer <oskar@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the change from mdio polling to irq, it became necessary to
restore the interrupt mask after resetting the chip in fec_stop().
Otherwise, with all irqs disabled, no communication with the PHY will be
possible after e.g. un-/replugging the cable and the device gets
stalled.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.

Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the move to phylib (commit e6b043d5) I was seeing sporadic "MDIO write
timeout" messages. Measure of the actual time spent showed latency times of
more than 1600us.

This patch uses the MII event indication of the FEC hardware to detect
completion of MDIO transactions.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 59d4289b converted fec to dev_pm_ops but
didn't update the suspend/resume functions thus leading to the following warning :
"initialization from incompatible pointer type" when CONFIG_PM is set.

This patch also fixe a few indentation and style around CONFIG_PM area.
Signed-off-by: NEric Bénard <eric@eukrea.com>
Cc: netdev@vger.kernel.org
Cc: davem@davemloft.net
Cc: amit.kucheria@canonical.com
Cc: s.hauer@pengutronix.de
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch compile tested only.

Convert legacy PM hooks to dev_pm_ops
Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleanup PHY probing: use helpers from phylib
Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert TX hook return value to netdev_tx_t
Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* in the actual driver, calling fec_stop and fec_enet_init doesn't
allow to have a working network interface at resume (where a
ifconfig down and up is required to recover the interface)
* by using fec_enet_close and fec_enet_open, this patch solves this
problem and handle the case where the link changed between suspend
and resume
* this patch also disable clock at suspend and reenable it at resume
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BugLink: http://bugs.launchpad.net/bugs/559065

In fec open/close function, we need to use phy_connect and phy_disconnect
operation before we start/stop phy. Otherwise it will cause system hang.

Only call fec_enet_mii_probe() in open function, because the first open
action will cause NULL pointer error.
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The i.MX25 PDK uses RMII to communicate with its PHY. This patch adds
the ability to configure RMII, based on platform data.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.

Exceptions are NETIF_F_LLTX drivers
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix memory corruption that sometimes result in kernel panic.
Signed-off-by: NMattias Walström <mattias@vmlinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Converts the list and the core manipulating with it to be the same as uc_list.

+uses two functions for adding/removing mc address (normal and "global"
 variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
 manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BugLink: http://bugs.launchpad.net/bugs/457878

v2:
 - remove duplicated phy_speed caculation
 - fix the phy_speed caculation according to the DataSheet

v1:
 - removed old MII phy control code
 - add phylib supporting
 - add ethtool interface to make user space NetworkManager works

Tested on Freescale i.MX51 Babbage board.

This patch is based on a patch from Frederic Rodo <fred.rodo@gmail.com>

Cc: Frederic Rodo <fred.rodo@gmail.com>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>
Acked-by: NAmit Kucheria <amit.kucheria@canonical.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.

Jirka
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The i.MX51 babbage board has a FEC ethernet controller with this phy.

In the long term we should resurrect the phylib patches for fec.
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fec driver was enabling receive buffer descriptor without allocating
the buffers. Make sure the buffer descriptors are initialized to not
start receiving packets.

Open also calls fec_restart after the rx buffers are allocated. With the code
in fec_restart, it zeroes out the buffer descriptors that have just been
setup.
Signed-off-by: NRob Herring <r.herring@freescale.com>
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fec_enet_init is called by both fec_probe and fec_resume, so it
shouldn't be marked as __init.
Signed-off-by: NSteven King <sfking@fdwdc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the ColdFire 5272 has full interrupt controller functionality
we can remove all the interrupt masking and acking code from the FEC
ethernet driver.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

fec_enet_mii, fec_enet_rx and fec_enet_tx are both only called by
fec_enet_interrupt in interrupt context.  So they must not use
spin_lock_irq/spin_unlock_irq.

This fixes:
	WARNING: at kernel/lockdep.c:2140 trace_hardirqs_on_caller+0x130/0x194()
	...
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Matt Waddel <Matt.Waddel@freescale.com>
Cc: netdev@vger.kernel.org
Cc: Tim Sander <tim01@vlsi.informatik.tu-darmstadt.de>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mii_discover_phy is only called by fec_enet_mii (via mip->mii_func).  So
&fep->mii_lock is already held and mii_discover_phy must not call
mii_queue which locks &fep->mii_lock, too.

This was noticed by lockdep:

	=============================================
	[ INFO: possible recursive locking detected ]
	2.6.31-rc8-00038-g37d0892c #109
	---------------------------------------------
	swapper/1 is trying to acquire lock:
	 (&fep->mii_lock){-.....}, at: [<c01569f8>] mii_queue+0x2c/0xcc

	but task is already holding lock:
	 (&fep->mii_lock){-.....}, at: [<c0156328>] fec_enet_interrupt+0x78/0x460

	other info that might help us debug this:
	2 locks held by swapper/1:
	 #0:  (rtnl_mutex){+.+.+.}, at: [<c0183534>] rtnl_lock+0x18/0x20
	 #1:  (&fep->mii_lock){-.....}, at: [<c0156328>] fec_enet_interrupt+0x78/0x460

	stack backtrace:
	Backtrace:
	[<c00226fc>] (dump_backtrace+0x0/0x108) from [<c01eac14>] (dump_stack+0x18/0x1c)
	 r6:c781d118 r5:c03e41d8 r4:00000001
	[<c01eabfc>] (dump_stack+0x0/0x1c) from [<c005bae4>] (__lock_acquire+0x1a20/0x1a88)
	[<c005a0c4>] (__lock_acquire+0x0/0x1a88) from [<c005bbac>] (lock_acquire+0x60/0x74)
	[<c005bb4c>] (lock_acquire+0x0/0x74) from [<c01edda8>] (_spin_lock_irqsave+0x54/0x68)
	 r7:60000093 r6:c01569f8 r5:c785e468 r4:00000000
	[<c01edd54>] (_spin_lock_irqsave+0x0/0x68) from [<c01569f8>] (mii_queue+0x2c/0xcc)
	 r7:c785e468 r6:c0156b24 r5:600a0000 r4:c785e000
	[<c01569cc>] (mii_queue+0x0/0xcc) from [<c0156b78>] (mii_discover_phy+0x54/0xa8)
	 r8:00000002 r7:00000032 r6:c785e000 r5:c785e360 r4:c785e000
	[<c0156b24>] (mii_discover_phy+0x0/0xa8) from [<c0156354>] (fec_enet_interrupt+0xa4/0x460)
	 r5:c785e360 r4:c077a170
	[<c01562b0>] (fec_enet_interrupt+0x0/0x460) from [<c0066674>] (handle_IRQ_event+0x48/0x120)
	[<c006662c>] (handle_IRQ_event+0x0/0x120) from [<c0068438>] (handle_level_irq+0x94/0x11c)
	...
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Matt Waddel <Matt.Waddel@freescale.com>
Cc: netdev@vger.kernel.org
Cc: Tim Sander <tim01@vlsi.informatik.tu-darmstadt.de>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>