Replace the numerical polarity flags with the PWM_POLARITY_INVERTED
symbolic constant.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NThierry Reding <thierry.reding@gmail.com>

This relfects the code and dts requires changes due to recent .dts
binding updates:
- use mg prefix for the Metor Graphics specific attributes
- use power in mA not in mA/2 as specifed in the USB2.0 specification
- remove the child node for USB. This is driver specific on won't be
  reflected in the device tree
- use the "mentor" prefix instead of "mg".
- use "dr_mode" istead of "mg,port-mode" for the port mode. The former
  is used by a few other drivers.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This moves the two instances from the big node into two child nodes. The
glue layer ontop does almost nothing.

There is one devices containing the control module for USB (2) phy,
(2) usb and later the dma engine. The usb device is the "glue device"
which contains the musb device as a child. This is what we do ever since.

The new file musb_am335x is just here to prob the new bus and populate
child devices.

There are a lot of changes to the dsps file as a result of the changes:

- musb_core_offset
  This is gone. The device tree provides memory ressources information
  for the device there is no need to "fix" things

- instances
  This is gone as well. If we have two instances then we have have two
  child enabled nodes in the device tree. For instance the SoC in beagle
  bone has two USB instances but only one has been wired up so there is
  no need to load and init the second instance since it won't be used.

- dsps_glue is now per glue device
  In the past there was one of this structs but with an array of two and
  each instance accessed its variable depending on the platform device
  id.

- no unneeded copy of structs
  I do not know why struct dsps_musb_wrapper is copied but it is not
  necessary. The same goes for musb_hdrc_platform_data which allocated
  on demand and then again by platform_device_add_data(). One copy is
  enough.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add pinmux configurations for RGMII based CPSW ethernet to AM335x EVMsk.

Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.

Sleep mode is nothing but the values required for the module during
inactive state. The pins are configured to its reset state to optimize
energy usage for the pins for the suspend/resume cycle
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

PWM output from ecap2 uses as backlight source. Also adds low threshold
value to have a uniform divisions in brightness-levels scales with
inverse polarity.
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
Reviewed-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Using constants for pinctrl allows a better readability, and removes
redundancy with comments.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Use standard GPIO constants to enhance the readability of DT GPIOs.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Replace /include/ by #include for AM33XX and AM35XX device tree
files, in order to use the C pre-processor, making use of #define
features possible.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

xdma_event_intr1.clkout2 pad can be used to source clock
from either 32K OSC or any of the PLL (except MPU) outputs.
On the existing AM335x based boards (EVM, EVM-SK and Bone),
this pad is used to feed the clock to audio codes.

So, this patch configures the pinmux to get clkout2 on the pad.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add pin control binding for UART0 device nodes in all
board specific DT files.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NMatt Porter <mporter@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

With DT support, where naming convention is based on base-addr
and not id, so we should follow TRM/Spec numbering label.

This patch changes UART numbering as per TRM, as uart0-5.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NMatt Porter <mporter@ti.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Now gpio-leds driver is using devm_pinctrl_get_select_default()
api to set default pinmux configuration required for the
functionality of the driver, so this patch moves respective
pinctrl binding inside leds node.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add pin control binding for I2C device nodes in all
board specific DT files (as per current usage),

EVM: Both i2c0 and i2c1
EVM-SK and Bone: Only i2c0
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NMatt Porter <mporter@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Adding phy-mode to CPSW node for beaglebone, EVM and EVMsk.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add phy_id device tree data to am335x-evmsk device to bring up CPSW
ethernet present on am335x starter kit.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename I2C and GPIO nodes according to AM33XX TRM. According to
AM33XX TRM device instances are starting from "0" like i2c0, i2c1
and i2c3.
Signed-off-by: NPantelis Antoniou <panto@antoniou-consulting.com>
[panto@antoniou-consulting.com: initial patch by pantelis's]
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add gpio based push buttons device tree data to am335x-evmsk device
by adding all the necessary parameters like key-code, gpios and etc.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add pinmux configurations for gpio based keys to am335x-evmsk. In
this patch, only single named mode/state is added and these pins
are configured during pinctrl driver initialization.

Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add gpio-leds device tree data to am335x-evmsk device to enable gpio
based user-leds (USR0, USR1, USR2 and USR3) present on am335x starter
kit.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add pinmux configurations for gpio based volume keys to am335x-evmsk.
In this patch, only single named mode/state is added and these pins
are configured during pinctrl driver initialization.

Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add AM335X EVM-SK device tree source (am335x-sk.dts) file to use
the am33xx.dtsi SoC file, along with the memory node information.

Also adds support for tps65910 regulator and lis331dlh accelerometer.
Following drivers/functionality were tested on AM335x-EVM-SK.
* I2C
* TPS65910 regulators
* lis331dlh accelerometer

AM335x EVM Starter Kit details can be accessed from:
http://www.ti.com/tool/tmdssk3358Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

In AM335x EVM tsl2550 ambient light sensor is connected to I2C2 bus.
Add child node inside i2c2 node with i2c slave address.

TAOS tsl2550 sensor is using a two-wire SMBus serial interface.
Reduce I2C2 clock frequency to 100kHz from 400kHz because the
maximum clock frequency of SMBus is 100kHz.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
[b-cousson@ti.com: Clean the changelog]
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add temperature sensor DT data to am335x-evm.dts. In AM335x EVM
tmp275 temperature sensor is connected to I2C2 bus. So this patch
adds child node inside i2c2 node with i2c slave address. This patch
is tested on AM335x EVM.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add lis331dlh device tree data to am335x-evm.dts. In AM335x EVM
lis331dlh accelerometer is connected to I2C2 bus. So this patch
change the status of I2C2 node to "okay" to use I2C2 bus. Also
added all the required platform data to am335x-evm.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add DT OPP table for AM33XX family of devices. This data is
decoded by OF with of_init_opp_table() helper function.

Also adds cpu0 supply name to the corresponding dts files.
cpu0-supply name is used by cpufreq-cpu0 driver to get the
regulator pointer for voltage modifications.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

To make it consistent, convert all hex number presentation
to lower-case from all am33xx specific nodes.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add tps65910 regulator device tree data to AM335x-EVM by adding
regulator consumers with tightened constraints and regulator-name.
TPS65910 regulator handle can be obtained by using this regulator
name.

This patch also add I2C node with I2C frequency and tps65910 PMIC
I2C slave address.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Ideally in common SoC dtsi file should set all modules
to "disabled" state and it should get enabled in respective
EVM/Board dts file as per usage.

This patch sets default status of all modules to "disabled"
state in am33xx.dtsi file. Currently there are no modules
supported as part of Bone and EVM dts support, so care
to add entry "status = "okay"" while adding support for any
module.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add AM335X EVM device tree source (am335x-evm.dts) file to
use the am33xx.dtsi SoC file, along with the memory node
information.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Reviewed-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Simple DTS file for OMAP2420H4 board adding memory information to allow
device-tree testing on an OMAP2420. OMAP2420H4 board has 64MB of RAM.

Verified that kernel boots with DT using a simple RAMDISK file-system on
OMAP2420H4.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add OMAP3 EVM (OMAP3530, AM/DM37x) DTS file to use the omap3.dtsi SoC file,
along with memory node information.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>