- 24 2月, 2015 29 次提交
-
-
由 Sergei Shtylyov 提交于
Define the Henninger board dependent part of the CAN0 device node. Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Sergei Shtylyov 提交于
Define the generic R8A7791 parts of the CAN0/1 device nodes. Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Sergei Shtylyov 提交于
The R-Car CAN controllers can derive the CAN bus clock not only from their peripheral clock input (clkp1) but also from the other internal clock (clkp2) and external clock fed on CAN_CLK pin. Describe those clocks in the device tree, along with the USB_EXTAL clock from which clkp2 is derived. Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Sergei Shtylyov 提交于
Define the generic R8A7790 parts of the CAN0/1 device nodes. Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Sergei Shtylyov 提交于
The R-Car CAN controllers can derive the CAN bus clock not only from their peripheral clock input (clkp1) but also from the other internal clock (clkp2) and external clock fed on CAN_CLK pin. Describe those clocks in the device tree, along with the USB_EXTAL clock from which clkp2 is derived. Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Niklas Söderlund 提交于
Configure the pinmux on kzm9d to use the serial connector for uart1. Signed-off-by: NNiklas Söderlund <niso@kth.se> Acked-by: NLinus Walleij <linus.walleij@linaro.org> Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Niklas Söderlund 提交于
With this information all GPIOs can make use of the PFC functionality. Signed-off-by: NNiklas Söderlund <niso@kth.se> Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: NLinus Walleij <linus.walleij@linaro.org> Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Wolfram Sang 提交于
Documentation says the last register is at 0x184 (CAxCPUCMCR), so use proper length. Current APMU code accesses CAxCPUnCR which is currently outside of the remapped area. Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Wolfram Sang 提交于
Documentation says the last register is at 0x184 (CAxCPUCMCR), so use proper length. Current APMU code accesses CAxCPUnCR which is currently outside of the remapped area. Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Add DT nodes for the ADV7511 HDMI encoder and its HDMI output connector and configure the DISP pin group that drives the HDMI transmitter DE pin. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: NSimon Horman <horms+renesas@verge.net.au> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Simon Horman 提交于
There appears to have been some inconsistency and confusion here as on the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3. Fixes: 59e79895 ("ARM: shmobile: r8a7791: Add clocks") Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
-
由 Simon Horman 提交于
* Correct base address of SD3 div6 clk. * Update div6 clock node labels There appears to have been some inconsistency and confusion here as on the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3. This has no run-time affect as the clock nodes are not currently used. Fixes: 8e181633 ("ARM: shmobile: r8a7794: Add SDHI clocks to device tree") Reported-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
-
由 Laurent Pinchart 提交于
Enable the ethernet controller for the Alt board. Pin muxing entries are currently left out as r8a7794 pin control support isn't available yet. We thus rely on the boot loader to configure ethernet pins for now. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Add a DT node for the on-SoC ethernet controller device. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Add the six IPMMU instances found in the r8a7794 to DT with a disabled status. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Add the seven IPMMU instances found in the r8a7791 to DT with a disabled status. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Add the six IPMMU instances found in the r8a7790 to DT with a disabled status. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Instantiate the two system DMA controllers in the r8a7794 device tree. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Geert Uytterhoeven 提交于
Traditionally, the first 16 MiB of RAM was reserved for the RT processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y, which requires that the start address of physical memory is a multiple of 128 MiB. As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare RAM to start at 0x40000000. While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is available. Note that kzm9g_defconfig still has CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so before the advent of DT we scribbled over the last 8 MiB, too. Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Geert Uytterhoeven 提交于
Traditionally, the first 16 MiB of RAM was reserved for the RT processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y, which requires that the start address of physical memory is a multiple of 128 MiB. As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare RAM to start at 0x40000000. While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is available. Note that kzm9g_defconfig still has CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so before the advent of DT we scribbled over the last 8 MiB, too. Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Ulrich Hecht 提交于
Specifies clock sources and register bits. Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com> [geert: Drop renesas,src-shift/renesas,src-width, pad to 4 or 8 parents] Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Geert Uytterhoeven 提交于
This clock drives the irqpin controller modules. Before, it was assumed enabled by the bootloader or reset state. By making it available to the driver, we make sure it gets enabled when needed, and allow it to be managed by system or runtime PM. Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Enable the kzm9g touchscreen controller in the board's DT file. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Geert Uytterhoeven 提交于
Add a DT node for the R2025D real-time clock, which is connected to i2c0. Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Geert Uytterhoeven 提交于
Add a DT node for the ADXL345 three-axis digital accelerometer sensor, which is connected to i2c0. As trivial i2c devices are matched against the first compatible entry only, compatibility is declared with "adi,adxl34x" only for now. Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> The device needs an interrupt to operate properly. Specify the two interrupts used on the board. While at it rename the DT node to accelerometer@1d to describe the device's function instead of its model. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Geert Uytterhoeven 提交于
Add a DT node for the AK8975 magnetometer sensor, which is connected to i2c0. Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Specify the device interrupt to avoid polling for end of conversion. While at it rename the DT node to compass@c to describe the device's function instead of its model. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Geert Uytterhoeven 提交于
While at it rename the ak4648 node to "codec" to describe the device's function instead of its model, and move its device-specific property after its generic properties. Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
The sh73a0 INTC can't mask interrupts properly most likely due to a hardware bug. Set the control-parent property to delegate masking to the parent interrupt controller. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Ulrich Hecht 提交于
This adds the remaining DIV6 clocks and all possible parents for the SUB clock. Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
- 23 2月, 2015 1 次提交
-
-
由 David Howells 提交于
Convert the following where appropriate: (1) S_ISLNK(dentry->d_inode) to d_is_symlink(dentry). (2) S_ISREG(dentry->d_inode) to d_is_reg(dentry). (3) S_ISDIR(dentry->d_inode) to d_is_dir(dentry). This is actually more complicated than it appears as some calls should be converted to d_can_lookup() instead. The difference is whether the directory in question is a real dir with a ->lookup op or whether it's a fake dir with a ->d_automount op. In some circumstances, we can subsume checks for dentry->d_inode not being NULL into this, provided we the code isn't in a filesystem that expects d_inode to be NULL if the dirent really *is* negative (ie. if we're going to use d_inode() rather than d_backing_inode() to get the inode pointer). Note that the dentry type field may be set to something other than DCACHE_MISS_TYPE when d_inode is NULL in the case of unionmount, where the VFS manages the fall-through from a negative dentry to a lower layer. In such a case, the dentry type of the negative union dentry is set to the same as the type of the lower dentry. However, if you know d_inode is not NULL at the call site, then you can use the d_is_xxx() functions even in a filesystem. There is one further complication: a 0,0 chardev dentry may be labelled DCACHE_WHITEOUT_TYPE rather than DCACHE_SPECIAL_TYPE. Strictly, this was intended for special directory entry types that don't have attached inodes. The following perl+coccinelle script was used: use strict; my @callers; open($fd, 'git grep -l \'S_IS[A-Z].*->d_inode\' |') || die "Can't grep for S_ISDIR and co. callers"; @callers = <$fd>; close($fd); unless (@callers) { print "No matches\n"; exit(0); } my @cocci = ( '@@', 'expression E;', '@@', '', '- S_ISLNK(E->d_inode->i_mode)', '+ d_is_symlink(E)', '', '@@', 'expression E;', '@@', '', '- S_ISDIR(E->d_inode->i_mode)', '+ d_is_dir(E)', '', '@@', 'expression E;', '@@', '', '- S_ISREG(E->d_inode->i_mode)', '+ d_is_reg(E)' ); my $coccifile = "tmp.sp.cocci"; open($fd, ">$coccifile") || die $coccifile; print($fd "$_\n") || die $coccifile foreach (@cocci); close($fd); foreach my $file (@callers) { chomp $file; print "Processing ", $file, "\n"; system("spatch", "--sp-file", $coccifile, $file, "--in-place", "--no-show-diff") == 0 || die "spatch failed"; } [AV: overlayfs parts skipped] Signed-off-by: NDavid Howells <dhowells@redhat.com> Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
-
- 21 2月, 2015 2 次提交
-
-
由 Niklas Cassel 提交于
Commit e9de688d ("irqchip: mips-gic: Support local interrupts") updated several platforms. This is a copy paste error. Signed-off-by: NNiklas Cassel <niklass@axis.com> Reviewed-by: NAndrew Bresticker <abrestic@chromium.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/9245/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Andreas Ruprecht 提交于
In commit c441d4a5 ("MIPS: mm: Only build one microassembler that is suitable"), the Makefile at arch/mips/mm was rewritten to only build the "right" microassembler file, depending on whether CONFIG_CPU_MICROMIPS is set or not. In the files, however, there are still preprocessor definitions depending on CONFIG_CPU_MICROMIPS. The #ifdef around them can now never evaluate to true, so let's remove them altogether. This inconsistency was found using the undertaker-checkpatch tool. Signed-off-by: NAndreas Ruprecht <rupran@einserver.de> Reviewed-by: NMaciej W. Rozycki <macro@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: Valentin Rothberg <valentinrothberg@gmail.com> Cc: Paul Bolle <pebolle@tiscali.nl> Patchwork: https://patchwork.linux-mips.org/patch/9267/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 20 2月, 2015 8 次提交
-
-
由 David Daney 提交于
- Use of_irq_init() to initialize interrupt controllers - Get rid of some unlikely() - Add CIB to support SATA and other interrupts - Add support for CIU SUM2 interrupt sources Signed-off-by: NDavid Daney <david.daney@cavium.com> Signed-off-by: NLeonid Rosenboim <lrosenboim@caviumnetworks.com> Signed-off-by: NAleksey Makarov <aleksey.makarov@auriga.com> Signed-off-by: NPeter Swain <peter.swain@cavium.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: devicetree@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/8947/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
The acknowledge bits don't exist for level triggered irqs, so setting them causes the simulator to terminate. Signed-off-by: NDavid Daney <david.daney@cavium.com> Signed-off-by: NLeonid Rosenboim <lrosenboim@caviumnetworks.com> Signed-off-by: NAleksey Makarov <aleksey.makarov@auriga.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/8946/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Chandrakala Chavva 提交于
Read clock rate from the correct CSR. Don't clear COP0_DCACHE for OCTEONIII. Signed-off-by: NChandrakala Chavva <cchavva@caviumnetworks.com> Signed-off-by: NAleksey Makarov <aleksey.makarov@auriga.com> Signed-off-by: NDavid Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/8945/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Chad Reese 提交于
CN38XX pass 1 required icache prefetching to be turned off. This chip never reached production and is long dead. Other processor specific icache settings are done by the bootloader. Remove these bits from the kernel. Signed-off-by: NChad Reese <kreese@caviumnetworks.com> Signed-off-by: NAleksey Makarov <aleksey.makarov@auriga.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Patchwork: https://patchwork.linux-mips.org/patch/8944/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
Signed-off-by: NDavid Daney <david.daney@cavium.com> Signed-off-by: NAleksey Makarov <aleksey.makarov@auriga.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/8943/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
Add coverage for OCTEON III models. Signed-off-by: NDavid Daney <david.daney@cavium.com> Signed-off-by: NAleksey Makarov <aleksey.makarov@auriga.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/8942/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
Make messages refer to all CN6XXX. Signed-off-by: NDavid Daney <david.daney@cavium.com> Signed-off-by: NAleksey Makarov <aleksey.makarov@auriga.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/8941/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
Also update union octeon_cvmemctl with new OCTEON II fields. [aleksey.makarov@auriga.com: use __BITFIELD_FIELD] Signed-off-by: NDavid Daney <david.daney@cavium.com> Signed-off-by: NAleksey Makarov <aleksey.makarov@auriga.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/8940/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-