Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
We do this by updating the ixgbe_is_sfp to be aware of the
new X550 devices.  This also includes a modified check generating
the EICR mask to be more forward-looking.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for receiving interrupts from a external copper
PHY for the X550 part.  This includes enabling, detection as well as
re-enablement.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The over heat message is displayed for multiple reasons but the text is
cut-n-pasted for each of these cases.  This patch pulls the text from the
same location.  I noticed this as I am about to add another case.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This new method will control the PHY power state.  You pass in the
state you wish to change to (ether on or off).  For cases where this
method is not used the current PHY power state behavior is maintained.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

These Device ID could support both WoL and autoneg flow control. In
the case of WoL this is indicated by the eeprom.  This patch enables
these devices this support.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some of the register addresses and format where unfortunately changed
between MAC types. To get around this we add a const u32 *mvals pointer
to the ixgbe_hw struct to point to an array of mac-type-dependent
values.  These can include register offsets, masks, whatever can be in
a u32. When the ixgbe_hw struct is initialized, a pointer to the
appropriate array must be set.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Because error codes are negative, it only makes sense to
consistently use signed types when handling them. Also remove
some explicit comparisons with 0 on these variables.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.

Libraries like libnl will wait forever for NLMSG_DONE.

Fixes: e5a55a89 ("net: create generic bridge ops")
Fixes: 815cccbf ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implements the new netdev op to allow user to enable/disable the ability
of a specific VF to query its RSS Indirection Table and an RSS Hash Key.

This patch limits the new feature support to 82599 and x540 devices only.
Support for other devices will be added later.
Signed-off-by: NVlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Added get_rxfh_indir_size, get_rxfh_key_size and get_rxfh ethtool_ops
callbacks implementations.

This enables the ethtool's "-x" and "--show-rxfh[-indir]" options.
Signed-off-by: NVlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a preparation for enablement of ethtool RSS indirection
table and hash key querying. We don't want to read registers every time
the RSS info is queried. Therefore we will store its current content in the
arrays in the adapter struct and will read it from there (instead of from
registers) when requested.

Will change the code that writes the indirection table and hash key into
the HW registers to take its content from these arrays. This will also
simplify the indirection table updating ethtool callback implementation
in the future.
Signed-off-by: NVlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ixgbe driver hasn't used call_rcu to free the rings for some time now.
Since that is the case the call to rcu_barrier can be dropped since calls
to kfree_rcu don't require it.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that the HW_VLAN_CTAG_FILTER bit is not falsely
advertised as being a feature that can be toggled on ixgbe parts.  The
driver was setting the bit in features and letting it be inherited by
hw_features, however the driver was actually ignoring the value of the bit
and just assuming it was always set.  As a result VLAN filtering was always
enabled which is a requirement for SR-IOV, VMDq, DCB, FCoE, and possibly
other features within the adapters.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch will enable X550 Source Address Prunning for VEPA
bridge mode.  This requires that we also have replication enabled
as well, while in this mode.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch gathers together all the logic needed to configure bridge
modes.  Currently that it is rather simple but this is really laying
the ground work for future X550 feature enhancement.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We are currently storing our BRIDGE_MODE as a bit in our adapter flags.
This patch will store the actual mode instead which minimizes obfuscation
and makes following patches for X550 simpler.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes some dead code from the cleanup path for ixgbe.

Setting and clearing the flag doesn't do anything since all we are
doing is setting the flag, scheduling NAPI, clearing the flag and
then letting netpoll do the polling cleanup.  As such it doesn't
make much sense to have it there.

This patch also removes one minor white-space error.

CC: <kernel-team@fb.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For the X550 mac type we have to do additional steps around
enabling/disabling Rx.  This patch will add a layer of indirection
around these support functions to enable this.

CC: <kernel-team@fb.com>
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.

$ git ls-files drivers/net/ethernet/ | \
  while read file ; do \
    codespell -w $file; \
  done

I removed a false positive in e1000_hw.h
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the built-in function instead of memset.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables the ethertype Anti-Spoofing feature for affected
devices. It is configured such that LLDP packets sent by a VF will
be dropped.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support VXLAN receive checksum offload in X550 hardware.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers

This is used later in this series
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
ixgbe_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.

Use vlan_get_protocol() to get the proper network protocol.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The same macros are used for rx as well. So rename it.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that dma_rmb is used when reading the Rx
descriptor.  The advantage of dma_rmb is that it allows for a much
lower cost barrier on x86, powerpc, arm, and arm64 architectures than a
traditional memory barrier when dealing with reads that only have to
synchronize to coherent memory.

In addition I have updated the code so that it just checks to see if any
bits have been set instead of just the DD bit since the DD bit will always
be set as a part of a descriptor write-back so we just need to check for a
non-zero value being present at that memory location rather than just
checking for any specific bit.  This allows the code itself to appear much
cleaner and allows the compiler more room to optimize.

Cc: Matthew Vick <matthew.vick@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change replaces calls to netdev_alloc_skb_ip_align with
napi_alloc_skb.  The advantage of napi_alloc_skb is currently the fact that
the page allocation doesn't make use of any irq disable calls.

There are few spots where I couldn't replace the calls as the buffer
allocation routine is called as a part of init which is outside of the
softirq context.

Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the Intel Ethernet drivers to use eth_skb_pad() and skb_put_padto
instead of doing their own implementations of the function.

Also this cleans up two other spots where skb_pad was called but the length
and tail pointers were being manipulated directly instead of just having
the padding length added via __skb_put.

Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver has logic to free up used data in case any of the checks in
ixgbe_probe() fail, however there is a similar set of cleanups that can
occur on driver unload in ixgbe_remove() which can cause the rmmod command
to crash.

This patch aims to fix the logic by moving pci_set_drvdata() after all error
checks and then adds a check in ixgbe_remove() to skip it altogether if
adapter comes up empty.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we now support X550 mac's bump the version number to reflect this.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch extends the function pointer structure to include the new
X550 class MAC types. This creates a new file ixgbe_x550.c that contains
all of the new methods.  Because of similarities to the X540 part in
some cases we just use it's methods where they can be used without any
modification.  These exported functions are now defined in the new
ixgbe_x540.h file.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The new X550 family of MAC's will have a larger RSS hash (16 -> 64).
It will also support individual VF to have their own independent RSS
hash key.  This patch will enable this functionality
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Accessing the CIAA/D register can block access to the PCI config space.

This patch removes the read/write operations to the CIAA/D registers
and makes use of standard kernel functions for accessing the PCI config
space.

In addition it moves ixgbevf_check_for_bad_vf() into the watchdog subtask
which reduces the frequency of the checks.

CC: Alex Williamson <alex.williamson@redhat.com>
Reported-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Attempt to look up the MAC address in Open Firmware on systems that
support it. On SPARC resort to using the IDPROM if no OF address is
found.
Signed-off-by: NMartin K Petersen <martin.petersen@oracle.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change cleans up the tail writes for the ixgbe descriptor queues.  The
current implementation had me confused as I wasn't sure if it was still
making use of the surprise remove logic or not.

It also adds the mmiowb which is needed on ia64, mips, and a couple other
architectures in order to synchronize the MMIO writes with the Tx queue
_xmit_lock spinlock.

Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up the page reuse code getting it into a state where all
the workarounds needed are in place as well as cleaning up a few minor
oversights such as using __free_pages instead of put_page to drop a locally
allocated page.

It also cleans up how we clear the descriptor status bits.  Previously they
were zeroed as a part of clearing the hdr_addr.  However the hdr_addr is a
64 bit field and 64 bit writes can be a bit more expensive on on 32 bit
systems.  Since we are no longer using the header split feature the upper
32 bits of the address no longer need to be cleared.  As a result we can
just clear the status bits and leave the length and VLAN fields as-is which
should provide more information in debugging.

Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

To allow brport device to return current brport flags set on port.  Add
returned flags to nested IFLA_PROTINFO netlink msg built in dflt getlink.
With this change, netlink msg returned for bridge_getlink contains the port's
offloaded flag settings (the port's SELF settings).
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ndo_bridge_setlink() is currently only called on the slave if
IFLA_AF_SPEC is set but this is a very fragile assumption and may
change in the future.

Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Payload is currently accessed blindly and may exceed valid message
boundaries.

Fixes: a77dcb8c ("be2net: set and query VEB/VEPA mode of the PF interface")
Fixes: 815cccbf ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>