Change the register name strings in the comments for the
twl6040_reg table, so it is easier to search for specific
register.

This is cosmetic change.

Before we had for example:
TWL6040_REG_HSLCTL as register definition.

At the register table we had:
TWL6040_HSLCTL

Searching for TWL6040_HSLCTL resulted no hits.

While if we look for REG_HSLCTL, we can find the places
the register has been used.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The default gains on outputs/inputs are set to 0dB.
This is fixing the pop noise issue at the first playback, which
caused by the wrong starting point of the ramp code.
The ramp code for the outputs expects the gains to be in
their lowest configuration in order to be effective.
After the playback stops, the ramp code takes care of
ramping down the gains to their minimum.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The model_id is no longer needed within the platform_data
for the TPA driver since the model of TPA specified
with the device name (tpa6130a2/tpa6140a2).

Also update rx51 (the only affected user) to use the device name rather
than platform data.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use the device name and driver_data to identify
the TPA model supported by the driver.
Board files should use either "tpa6130a2" or
"tpa6140a2" as device name to specify the model
in used on the specific board.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reset the codec according to the Audio power-up delay errata for the 88PM8607.
Signed-off-by: NBas Vermeulen <bas.vermeulen@novero.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Introduce a I2S CLK supply so playback and capture can operate independently.
Signed-off-by: NBas Vermeulen <bas.vermeulen@novero.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NJohnny Hsu <johnnyhsu@realtek.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM5100 is a highly integrated low power audio subsystem with advanced
digital signal processing capabilities including effects, speech clarity
enhancement and active noise cancellation.  This initial driver provides
support for basic audio paths, further patches will provide more
complete functionality.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

The driver assumes that control_data points to the drivers i2c_client struct,
but this is no longer the case since the ASoC core has switched to regmap.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This functionality is now subsumed within the bias management, using the
standard cache management functionality, without assuming the cache type.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

For digital only paths we need to make sure the bandgap is enabled prior
to starting the FLL which isn't tied into DAPM.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

twl6040 supports 5 playback, and 2 capture channels
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Only mono audio can be used for vibra (DL4 channel).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reset the twl6040_reg array to hold the chip default values.
The only changed values were for the microphone input selection.
Select no input for the microphones in the twl6040_init_chip function.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There is no need to write to the vio registers at probe time, since most
them either read only, or shared with MFD or not used.
On the other hand it is a good idea to updated the ASICREV register in
the cache at this time.

After power up we need to restore some registers. Clean up the list to
contain only the registers we are going to restore.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NVinod Koul <vinod.koul@linux.intel.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM8996 can measure the impedance of accessories connected to the
headphone output. Implement initial support for this, measuring the
left channel impedance when an accessory is detected and using this
to distinguish between a line load and a headphone load.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Rather than managing the bandgap in the bias level control use a supply
widget as we only actually need to enable it for analogue paths, not
fully digital ones.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

The WM8776 supports a continuous range of sample rates rather than
discrete values and supports a wider range of sample rates on the
playback path than is currently supported.  Update the constraints on
the DAIs to reflect this.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The i2c core will clear the clientdata pointer automatically,
we don't have to set the `data' field to NULL in remove() or
if probe() failed anymore.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use snd_pcm_format_width() to determine the sample size, instead of
checking specify sample formats and assuming that those are the only
valid format.

This change adds support for big-endian architectures (which use the _BE
formats) and the packed 24-bit format (SNDRV_PCM_FORMAT_S24_3xE).

[Fixed single letter variable name legibility problem -- broonie]
Signed-off-by: NTimur Tabi <timur@freescale.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We need to count the timeout down.
Reported-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

The AIF1 channels are numbered from zero than one; do the same thing for
AIF2 too.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

The WM8996 only requires CPVDD when the charge pump is active so control
it separately to the other supplies, only enabling it when the charge pump
is active. This will result in a small power saving on systems which are
able to provide independent software control of the supply.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Currently register read-back for the ad193x is broken, because it expects bit 0
of the upper byte to be set to indicate a read operation, while the regmap
default for SPI is to use bit 7.

This patch also addresses another oddity of the device. There are SPI and I2C
versions of this codec. In both cases the registers are 8-bit wide and numbered
from 0x0 to 0x10, but in the SPI case there is also a so called
'global address' which is prefixed in-front of the register address. The global
address mimics I2C behaviour and includes a static device address the and the
read/write flag. This basically extends the register address to an 16-bit value
numbered from 0x800 to 0x810. These are the register numbers which are
currently used by the driver. This works, because I2C will ignore the upper
8 bits of the register, but it is still a bit confusing, as there are no such
register numbers in the I2C case.

The approach taken by this patch is to number the registers from 0x00 to 0x10
and encode the global address for SPI mode into the read and write flag masks.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Return -ENODEV instead of 0 if vendor id mismatch.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We can directly read the FLL lock status on WM8996 so even if we don't
have an interrupt wired up we can still verify that the FLL started
successfully.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

In the case of no free channel available,
current implementation returns 0 instead of negative errno.

This patch fixes the logic to return -EINVAL if no free channel available.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NVinod Koul <vinod.koul@linux.intel.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Similarly to PLLs/FLLs some modern CODECs provide selectable system clock
sources. When the clock is the clock for a DAI we do not usually need to
identify which clock is being configured so can use clk_id for the source
clock but with CODEC wide system clocks we will need to specify both the
clock being configured and the source.

Add a source argument to the CODEC driver set_sysclk() operation to
reflect this. As this operation is not as widely used as the DAI
set_sysclk() operation the change is not very invasive. We probably
ought to go and make the same alternation for DAIs at some point.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NTimur Tabi <timur@freescale.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

My first patch to ASoC ever! If I did something wrong, blame Ian.
Signed-off-by: NSusan Gao <sgao@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>