omap_video_timings can be replaced with the generic videomode in omapdrm
and the omap_video_timings can be removed.

This patch will replace the omap_video_timings with videomode.
With the change we no longer need the functions to convert to/from
videomode and drm_display_mode to omap_video_timings, these can be removed
as well.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for sync edge.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for pixel data edge.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for DE level.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for h/vsync level.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Remove the interlace member and add display_flags to omap_video_timings to
configure the interlace mode.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the vbp member to vback_porch.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the vfp member to vfront_porch.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the vsw member to vsync_len.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the hbp member to hback_porch.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the hfp member to hfront_porch.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the hsw member to hsync_len.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the y_res member to vactive.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the x_res member to hactive.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Fix the retrn value check which testing the wrong variable
in dsi_bind().
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

All drivers to include the omapdrm/dss/omapdss.h header file. This header
includes the <video/omapdss.h>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>

regulator_can_change_voltage() is deprecated and it's use is not necessary
as commit:
6a0028b3 regulator: Deprecate regulator_can_change_voltage()
describers it clearly.

Also, regulator_set_voltage() is misused in the driver, as it is
supposed to be used only in cases where the regulator voltage needs to
be changed dynamically at runtime. In DSS's case, we always want a fixed
voltage, set in the .dts files.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add a "_a" postfix to the type A PLL calc functions, to differentiate
them from the type B PLL calculations which we will add shortly.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSS uses two types of PLLs, type A (DSI & Video) and type B (HDMI). The
two types behave slightly differently, but we don't have the type of the
PLL available anywhere for the driver.

This patch adds an enum for the PLL type and a field in the PLL's HW
data to store it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The names of the enum dss_clk_source's values are legacy names, only
correct for OMAP3 DSS. Rename the names to more generic ones.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that there is no "non-generic" version of the function to get the
clock source name, lets rename dss_get_generic_clk_source_name() to
dss_get_clk_source_name().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We have two functions to return a name for clock sources for debugging
purposes: dss_feat_get_clk_source_name() and
dss_get_generic_clk_source_name().

The former is supposed to return a DSS IP version specific name for the
clock source, and the latter is supposed to return a more generic name.

All this seems a bit pointless, so let's remove the former one.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

'enum omap_dss_clk_source' is internal to dss. Let's rename it to
'dss_clk_source' match our naming convention.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing the uses of 'struct omap_overlay_manager'. This patch
changes DSI driver to use 'omap_channel' instead.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The DSS output drivers check 'dssdev->manager' in disconnect()
functions. This check is not needed as the manager must always be set if
the output device was connected. Remove the check.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_unregister_framedone_handler() to accept 'enum
omap_channel' instead of 'struct omap_overlay_manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_register_framedone_handler() to accept 'enum
omap_channel' instead of 'struct omap_overlay_manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_start_update() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_disable() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_enable() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_set_lcd_config() to accept 'enum omap_channel' instead
of 'struct omap_overlay_manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_set_timings() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_disconnect() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_connect() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use 'out->dispc_channel_connected' to check if the device is connected
to an overlay manager or not, instead of using 'out->manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that omapfb has its own copy of omapdss and display drivers, we can
move omapdss and display drivers which omapdrm uses to omapdrm's
directory.

We also need to change the main drm Makefile so that omapdrm directory
is always entered, because omapdss has a file that can't be built as a
module.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Acked-by: NRob Clark <robdclark@gmail.com>

DSI_IRQ_SYNC_LOST was ORed twice so we can remove one.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

All the output drivers check for 'out' being NULL, but it can never be
NULL. Remove the check.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

omapdss kernel module contains drivers for multiple devices, one for
each DSS submodule. The probing we have at the moment is a mess, and
doesn't give us proper deferred probing nor ensure that all the devices
are probed before omapfb/omapdrm start using omapdss.

This patch solves the mess by using the component system for DSS
submodules.

The changes to all DSS submodules (dispc, dpi, dsi, hdmi4/5, rfbi, sdi,
venc) are the same: probe & remove functions are changed to bind &
unbind, and new probe & remove functions are added which call
component_add/del.

The dss_core driver (dss.c) acts as a component master. Adding and
matching the components is simple: all dss device's child devices are
added as components.

However, we do have some dependencies between the drivers. The order in
which they should be probed is reflected by the list in core.c
(dss_output_drv_reg_funcs). The drivers are registered in that order,
which causes the components to be added in that order, which makes the
components to be bound in that order. This feels a bit fragile, and we
probably should improve the code to manage binds in random order.
However, for now, this works fine.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>