- 10 7月, 2012 37 次提交
-
-
由 Anton Blanchard 提交于
Similar to PCI, separate the bus probe from device probe. This allows us to attach bus notifiers for DMA debug and IOMMU fault injection before devices have been probed. Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Anton Blanchard 提交于
During boot we see a number of these warnings: vio 30000000: Warning: IOMMU dma not supported: mask 0xffffffffffffffff, table unavailable The reason for this is that we set IOMMU properties for all VIO devices even if they are not DMA capable. Only set DMA ops, table and mask for devices with a DMA window. Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
Signed-off-by: NMichael Neuling <mikey@neuling.org> Acked-by: NGavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Anton Blanchard 提交于
We use SIAR or regs->nip for the instruction pointer depending on the PMU configuration, but we always use regs->nip in the callchain. Use perf_instruction_pointer so the backtrace is consistent. Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Anton Blanchard 提交于
At the moment we always use the SIAR if the PMU supports continuous sampling. Unfortunately the SIAR and the PMU exception are not synchronised for non marked events so we can end up with callchains that dont make sense. The following patch checks the HV and PR bits for samples coming from userspace and always uses pt_regs for them. Userspace will never have interrupts off so there is no real advantage to using the SIAR for non marked events in userspace. I had experimented with a patch that did a similar thing for kernel samples but we lost a significant amount of information. I was unable to profile any of our early exception code for example. Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Anton Blanchard 提交于
The logic to choose whether to use the SIAR or get the information out of pt_regs is going to get more complicated, so do it once in perf_read_regs. We overload regs->result which is gross but we are already doing it with regs->dsisr. Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Anton Blanchard 提交于
We want to access the MMCRA_SIHV and MMCRA_SIPR bits elsewhere so create mmcra_sihv and mmcra_sipr which hide the differences between the old and new layout of the bits. Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
Some macros use RA where when RA=R0 the values is 0, so make this the enforced mnemonic in the macro. Idea suggested by Andreas Schwab. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
R0 is special since it'll be 0. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
Enforce the use of R0-R31 in macros where possible now we have all the fixes in. R0-R31 macros are removed here so that can't be used anymore. They should not be defined anywhere. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
Now have ___PPC_RA/B/S/T we can use it in some places. These are places where we can't use the existing defines which will soon enforce R0-R31 usage. The macros being changed here are being used in inline asm, which can't convert to enforce the R0-R31 usage. bpf_jit uses a mix of both generated and non-generated with the same code, so just convert all these to use the ___PPC_R versions which won't enforce R usage later. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
These are currently the same as __PPC_RA/B/S/T but we'll wrap them soon. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
We need to do this so we can enforce the name of a and b in called macros PPC_RA/B later. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
These macros are using integers where they could be using logical names since they take registers. We are going to enforce this soon, so fix these up now. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
LOAD_REG_ADDR define is just a wrapper around real instructions so we can just use real register names here (ie. lower case). Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
mtocrf define is just a wrapper around the real instructions so we can just use real register names here (ie. lower case). Also remove braces in macro so this is possible. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Benjamin Herrenschmidt 提交于
Move this duplicated definition to ppc_asm.h and remove the braces which prevent the use of %rN register names Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
Merge the defines of VCPU_GPR from different places. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
Merge the defines of STACKFRAMESIZE, STK_REG, STK_PARAM from different places. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
move lbz/stbciz to ppc-opcode.h. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
Now all the fixes are in place, let's rock-n-roll! Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
Anything that uses a constructed instruction (ie. from ppc-opcode.h), need to use the new R0 macro, as %r0 is not going to work. Also convert usages of macros where we are just determining an offset (usually for a load/store), like: std r14,STK_REG(r14)(r1) Can't use STK_REG(r14) as %r14 doesn't work in the STK_REG macro since it's just calculating an offset. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
The assembler doesn't take %r0 register arguments in braces, so remove them. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Michael Neuling 提交于
We are going to use these later and convert r0 to %r0 etc. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Benjamin Herrenschmidt 提交于
We want to bring in the latest IRQ fixes
-
由 Benjamin Herrenschmidt 提交于
udbg_init_debug_opal() should be udbg_init_debug_opal_raw() as the caller in arch/powerpc/kernel/udbg.c expects Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Benjamin Herrenschmidt 提交于
Newer gcc are being a bit blind here (it's pretty obvious we don't reach the code path using the array if we haven't initialized the pointer) but none of that is performance critical so let's just silence it. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Benjamin Herrenschmidt 提交于
There was a typo, checking for CONFIG_TRACE_IRQFLAG instead of CONFIG_TRACE_IRQFLAGS causing some useful debug code to not be built This in turns causes a build error on BookE 64-bit due to incorrect semicolons at the end of a couple of macros, so let's fix that too Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> CC: stable@vger.kernel.org [v3.4]
-
由 Benjamin Herrenschmidt 提交于
Looks like we still have issues with pSeries and Cell idle code vs. the lazy irq state. In fact, the reset fixes that went upstream are exposing the problem more by causing BUG_ON() to trigger (which this patch turns into a WARN_ON instead). We need to be careful when using a variant of low power state that has the side effect of turning interrupts back on, to properly set all the SW & lazy state to look as if everything is enabled before we enter the low power state with MSR:EE off as we will return with MSR:EE on. If not, we have a discrepancy of state which can cause things to go very wrong later on. This patch moves the logic into a helper and uses it from the pseries and cell idle code. The power4/970 idle code already got things right (in assembly even !) so I'm not touching it. The power7 "bare metal" idle code is subtly different and correct. Remains PA6T and some hypervisor based Cell platforms which have questionable code in there, but they are mostly dead platforms so I'll fix them when I manage to get final answers from the respective maintainers about how the low power state actually works on them. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> CC: stable@vger.kernel.org [v3.4]
-
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator由 Linus Torvalds 提交于
Pull regulator fix from Mark Brown: "A smallish fix for a lock dependency issue which affects a bunch of Qualcomm boards that do unusually complicated things with their regulators, the API is unlikely to be called by any other system." * tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: regulator: Fix recursive mutex lockdep warning
-
由 Hans de Goede 提交于
Don't call v4l2_ctrl_g_ctrl on ctrls which the model cam in question does not have. Reported-by: NFrank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com> [ Taken directly, since Mauro is on vacation ] Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Linus Torvalds 提交于
Merge tag 'virtio-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus Pull minor virtio-balloon fix from Rusty Russell: "Theoretical fix, which greatly simplifies upcoming balloon patches which will go in via some vm tree." * tag 'virtio-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: virtio-balloon: fix add/get API use
-
git://git.kernel.org/pub/scm/linux/kernel/git/ohad/rpmsg由 Linus Torvalds 提交于
Pull rpmsg fixes from Ohad Ben-Cohen: "Fixing two (somewhat rare) endpoint-related race issues, both of which were reported by Fernando Guzman Lugo." * tag 'rpmsg-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/rpmsg: rpmsg: make sure inflight messages don't invoke just-removed callbacks rpmsg: avoid premature deallocation of endpoints
-
git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc由 Linus Torvalds 提交于
Pull remoteproc fixes from Ohad Ben-Cohen: "Two build-related remoteproc fixes for 3.5." * tag 'remoteproc-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc: remoteproc: fix missing CONFIG_FW_LOADER configurations remoteproc/omap: fix randconfig unmet direct dependencies
-
git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock由 Linus Torvalds 提交于
Pull hwspinlock fix from Ohad Ben-Cohen: "A single hwspinlock core fix for multiple hwspinlock devices scenarios, from Shinya Kuribayashi." * tag 'hwspinlock-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock: hwspinlock/core: use global ID to register hwspinlocks on multiple devices
-
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu由 Linus Torvalds 提交于
Pull IOMMU fixes from Joerg Roedel: "The patches fix several issues in the AMD IOMMU driver, the NVidia SMMU driver, and the DMA debug code. The most important fix for the AMD IOMMU solves a problem with SR-IOV devices where virtual functions did not work with IOMMU enabled. The NVidia SMMU patch fixes a possible sleep while spin-lock situation (queued the small fix for v3.5, a better but more intrusive fix is coming for v3.6). The DMA debug patches fix a possible data corruption issue due to bool vs u32 usage." * tag 'iommu-fixes-v3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: iommu/amd: fix type bug in flush code dma-debug: debugfs_create_bool() takes a u32 pointer iommu/tegra: smmu: Fix unsleepable memory allocation iommu/amd: Initialize dma_ops for hotplug and sriov devices iommu/amd: Fix missing iommu_shutdown initialization in passthrough mode
-
- 09 7月, 2012 2 次提交
-
-
由 Michael S. Tsirkin 提交于
Since ee7cd898 'virtio: expose added descriptors immediately.', in virtio balloon virtqueue_get_buf might now run concurrently with virtqueue_kick. I audited both and this seems safe in practice but this is not guaranteed by the API. Additionally, a spurious interrupt might in theory make virtqueue_get_buf run in parallel with virtqueue_add_buf, which is racy. While we might try to protect against spurious callbacks it's easier to fix the driver: balloon seems to be the only one (mis)using the API like this, so let's just fix balloon. Signed-off-by: NMichael S. Tsirkin <mst@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (removed unused var)
-
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup由 Linus Torvalds 提交于
Pull cgroup fixes from Tejun Heo: "The previous cgroup pull request contained a patch to fix a race condition during cgroup hierarchy umount. Unfortunately, while the patch reduced the race window such that the test case I and Sasha were using didn't trigger it anymore, it wasn't complete - Shyju and Li could reliably trigger the race condition using a different test case. The problem wasn't the gap between dentry deletion and release which the previous patch tried to fix. The window was between the last dput() of a root's child and the resulting dput() of the root. For cgroup dentries, the deletion and release always happen synchronously. As this releases the s_active ref, the refcnt of the root dentry, which doesn't hold s_active, stays above zero without the corresponding s_active. If umount was in progress, the last deactivate_super() proceeds to destory the superblock and triggers BUG() on the non-zero root dentry refcnt after shrinking. This issue surfaced because cgroup dentries are now allowed to linger after rmdir(2) since 3.5-rc1. Before, rmdir synchronously drained the dentry refcnt and the s_active acquired by rmdir from vfs layer protected the whole thing. After 3.5-rc1, cgroup may internally hold and put dentry refs after rmdir finishes and the delayed dput() doesn't have surrounding s_active ref exposing this issue. This pull request contains two patches - one reverting the previous incorrect fix and the other adding the surrounding s_active ref around the delayed dput(). This is quite late in the release cycle but the change is on the safer side and fixes the test cases reliably, so I don't think it's too crazy." * 'for-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: cgroup: fix cgroup hierarchy umount race Revert "cgroup: superblock can't be released with active dentries"
-
- 08 7月, 2012 1 次提交
-
-
由 Linus Torvalds 提交于
-