The core spi driver swaps the polarity of the enable based on SPI_CS_HIGH.
The omap2 controller has an internal configuration register bit called
OMAP2_MCSPI_CHCONF_EPOL to handle active high chip selects as well.

So we have to revert swap the polarity back for the correct setting of the
OMAP2_MCSPI_CHCONF_FORCE bit in omap2_mcspi_set_cs.
Signed-off-by: NMichael Welling <mwelling@ieee.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

The core spi driver handles the delay between transactions.
This is a remanant from the transfer_one conversion.
Signed-off-by: NMichael Welling <mwelling@ieee.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

GPIO chip select patch series appears to have broken the native chip select
support. This patch pulls the manual native chip select toggling out of
the transfer_one routine and adds a set_cs routine.

Tested natively on AM3354 with SPI serial flash on spi0cs0.
Reported-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NMichael Welling <mwelling@ieee.org>
Tested-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

If GPIO chip select is specified, request the GPIO in the setup function
and release it in the cleanup function.
Signed-off-by: NMichael Welling <mwelling@ieee.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

Switches from transfer_one_message to transfer_one to prepare driver for
use of GPIO chip selects.
Signed-off-by: NMichael Welling <mwelling@ieee.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

The spi queue waits forever for spi_finalize_current_message() to be
called, blocking the bus.  Ensure that all error paths from
omap2_mcspi_transfer_one_message() call spi_finalize_current_message().
Signed-off-by: NFionn Cleary <fionn.cleary@streamunlimited.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The spi hangs waiting the completion of omap2_mcspi_rx_callback.
Signed-off-by: NJorge A. Ventura <jorge.araujo.ventura@gmail.com>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

Commit id 2bd16e3e
(spi: omap2-mcspi: Do not configure the controller
on each transfer unless needed) does its job too
well so omap2_mcspi_setup_transfer() isn't called
even when an SPI slave driver changes 'spi->mode'.
The result is that the mode requested by the SPI
slave driver never takes effect.

Fix this by adding the 'mode' member to the
omap2_mcspi_cs structure which holds the mode
value that the hardware is configured for.
When the SPI slave driver changes 'spi->mode'
it will be different than the value of this new
member and the SPI master driver will know that
the hardware must be reconfigured (by calling
omap2_mcspi_setup_transfer()).

Fixes: 2bd16e3e (spi: omap2-mcspi: Do not configure the controller on each transfer unless needed)
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

This saves a few unwind code and return proper error if devm_kcalloc fails.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Set master->max_speed_hz and master->min_speed_hz then spi core will handle
checking transfer speed. So we can remove the same checking in this driver.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This checking is done in __spi_validate().
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Currently a divide-by-2^n clock is used, causing a very coarse
clock selection, i.e. a 10MHz device will need to use a 6MHz
clock. The McSPI can also use a divide-by-n clock, this patch
adds support for selecting that when possible.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

spi_transfer->speed_hz and spi_transfer->bits_per_word used to only be set when
not using the default settings but are not set on every transfer, causing
omap2_mcspi_setup_transfer to be called on each transfer. This patch changes
the check to only call omap2_mcspi_setup_transfer if the settings needs to be
changed.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.

Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: NVictor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: NTaras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch fixes MCSPI FIFO buffer support when transmit-and-receive
(full duplex) mode is used. In this mode FIFO can be used for RX or
for TX or for both directions. If FIFO used for both directions the buffer
is split into two 32-byte buffers - one for each direction.
Also for full duplex mode both AEL and AFL need to be set in CHCONF0 register.
Signed-off-by: NIllia Smyrnov <illia.smyrnov@globallogic.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Use devm_spi_register_master() to make cleanup paths simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>
Reviewed-by: NFelipe Balbi <balbi@ti.com>

Convert dmaengine channel requests to use
dma_request_slave_channel_compat(). This supports the DT case of
platforms requiring channel selection from either the OMAP DMA or
the EDMA engine. AM33xx only boots from DT and is the only user
implementing EDMA so in the !DT case we can default to the OMAP DMA
filter.
Signed-off-by: NMatt Porter <mporter@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NJoel A Fernandes <joelagnel@ti.com>
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The MCSPI controller has a built-in FIFO buffer to unload the DMA or interrupt
handler and improve data throughput. This patch adds FIFO buffer support for SPI
transfers in DMA mode.

For SPI transfers in DMA mode, the largest possible FIFO buffer size will be
calculated and set up. The FIFO won't be used for the SPI transfers in DMA mode
if: calculated FIFO buffer size is less then 2 bytes or the FIFO buffer size
isn't multiple of the SPI word length.
Signed-off-by: NIllia Smyrnov <illia.smyrnov@ti.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Introduce mcspi_bytes_per_word function as replacement for the next code
fragment:

int c = (word_len <= 8)  ? 1 :
	(word_len <= 16) ? 2 :
	/* word_len <= 32 */ 4;

This code used 2 times in current driver code and will be used 2 times in
the next FIFO buffer support patch. Replace it with inline function with clear
name to improve code legibility.
Signed-off-by: NIllia Smyrnov <illia.smyrnov@ti.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Fill in the recently added spi_master.bits_per_word_mask field in as
many drivers as possible. Make related cleanups, such as removing any
redundant error-checking, or empty setup callbacks.
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since commit ab78029e (drivers/pinctrl: grab default handles from device
core) we can rely on device core for handling pinctrl so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Selecting CONFIG_DMADEVICES is optional, and we must
be able to continue even without DMA. Otherwise things
like omap4430sdp nfsroot will fail if DMA is not
selected.

Note that the driver already supports PIO mode, but
we fail to fall back to PIO if requesting DMA channels
fails.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It is possible that the handler gets interrupted after checking the
status. After it resumes the time out is due but the condition it was
waiting for might be true as well. Therefore it is necessary to check
the condition in case of an time out to be sure that the condition is
not true after the time passed by.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

No actual errors have been found for completing
before disabling DMA request lines, but it just
looks more semantically correct that on our DMA
callback we quiesce the whole thing before stating
transfer is finished.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch allows the board code to define SPI devices which needs to
toggle the chip select after every word send. This is needed to get a
better resolution reading e.g. an ADC data stream.
Apart from that, as in the normal code CS is controlled by software,
a transfer is done much faster.
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch fixes some indentation errors.
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.

devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.

Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

linux/err.h was included twice.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix the below warning
drivers/spi/spi-omap2-mcspi.c:336:34: warning: symbol 'tx' shadows an earlier one
drivers/spi/spi-omap2-mcspi.c:327:12: originally declared here

So delete the u8 tx as it is assigned and not used(resigned afterwards).
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Remove duplicated include.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

0384e90b ("spi/mcspi: allow configuration of pin directions") did what
it claimed to do the wrong way around. D0/D1 is configured as output by
*clearing* the bits in the conf registers, hence also breaking the
former default behaviour.

Fix this before that change is merged to mainline.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>