Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 09 6月, 2009 1 次提交
  3. 24 5月, 2009 1 次提交
    • M
      [SCSI] iscsi: pass ep connect shost · 10eb0f01
      由 Mike Christie 提交于 
      When we create the tcp/ip connection by calling ep_connect, we currently
just go by the routing table info.

I think there are two problems with this.

1. Some drivers do not have access to a routing table. Some drivers like
qla4xxx do not even know about other ports.

2. If you have two initiator ports on the same subnet, the user may have
set things up so that session1 was supposed to be run through port1. and
session2 was supposed to be run through port2. It looks like we could
end with both sessions going through one of the ports.

Fixes for cxgb3i from Karen Xie.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
      10eb0f01
  5. 16 5月, 2009 1 次提交
    • A
      [SCSI] fc-transport: Close state transition-window during rport deletion. · 9a1a69a1
      由 Andrew Vasquez 提交于 
      Andrew Vasquez wrote:
> fc-transport: Close state transition-window during rport deletion.
>
> After an rport's state has transitioned to FC_PORTSTATE_BLOCKED,
> but, prior to making the upcall to 'block' the scsi-target
> associated with an rport, queued commands can recycle and
> ultimately run out of retries causing failures to propagate to
> upper-level drivers.  Close this transition-window by returning
> the non-'retries' modifying DID_IMM_RETRY status for submitted
> I/Os.

The same can happen for iscsi when transitioning from logged in
to failed and blocking the sdevs.

This patch converts iscsi and fc's transitions back to use DID_IMM_RETRY
instead of DID_TRANSPORT_DISRUPTED which has a limited number of retries
that we do not want to use for handling this race.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
[Addition of iscsi and fc port online devloss case conversion by Mike Christie]
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
      9a1a69a1
  7. 14 3月, 2009 2 次提交
  9. 06 2月, 2009 1 次提交
    • P
      netlink: change return-value logic of netlink_broadcast() · ff491a73
      由 Pablo Neira Ayuso 提交于 
      Currently, netlink_broadcast() reports errors to the caller if no
messages at all were delivered:

1) If, at least, one message has been delivered correctly, returns 0.
2) Otherwise, if no messages at all were delivered due to skb_clone()
   failure, return -ENOBUFS.
3) Otherwise, if there are no listeners, return -ESRCH.

With this patch, the caller knows if the delivery of any of the
messages to the listeners have failed:

1) If it fails to deliver any message (for whatever reason), return
   -ENOBUFS.
2) Otherwise, if all messages were delivered OK, returns 0.
3) Otherwise, if no listeners, return -ESRCH.

In the current ctnetlink code and in Netfilter in general, we can add
reliable logging and connection tracking event delivery by dropping the
packets whose events were not successfully delivered over Netlink. Of
course, this option would be settable via /proc as this approach reduces
performance (in terms of filtered connections per seconds by a stateful
firewall) but providing reliable logging and event delivery (for
conntrackd) in return.

This patch also changes some clients of netlink_broadcast() that
may report ENOBUFS errors via printk. This error handling is not
of any help. Instead, the userspace daemons that are listening to
those netlink messages should resync themselves with the kernel-side
if they hit ENOBUFS.

BTW, netlink_broadcast() clients include those that call
cn_netlink_send(), nlmsg_multicast() and genlmsg_multicast() since they
internally call netlink_broadcast() and return its error value.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ff491a73
  11. 03 1月, 2009 1 次提交
  13. 13 10月, 2008 3 次提交
  15. 04 10月, 2008 1 次提交
    • J
      [SCSI] scsi_host_lookup: error returns and NULL pointers · 315cb0ad
      由 James Smart 提交于 
      This patch cleans up the behavior of scsi_host_lookup().

The original implementation attempted to use the dual role of
either returning a pointer value, or a negative error code.
User's needed to use IS_ERR() to check the result. Additionally,
the IS_ERR() macro never checks for when a NULL pointer was
returned, so a NULL pointer actually passes with a success case.
Note: scsi_host_get(), used by scsi_host_lookup(), can return
a NULL pointer.

Talk about a mudhole for the unitiated to step into....

This patch converts scsi_host_lookup() to return either NULL
or a valid pointer. The consumers were updated for the change.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
      315cb0ad
  17. 22 7月, 2008 2 次提交
  19. 12 7月, 2008 12 次提交
  21. 20 4月, 2008 1 次提交
  23. 06 3月, 2008 1 次提交
  25. 28 2月, 2008 1 次提交
  27. 22 2月, 2008 1 次提交
  29. 08 2月, 2008 6 次提交
  31. 29 1月, 2008 1 次提交
  33. 12 1月, 2008 4 次提交