There are a number of small form factor desktop systems with Intel mobile
graphics chips that lie and say they have an LVDS. With kernel mode-setting,
this becomes a problem, and makes native resolution boot go haywire -- for
example, my Dell Studio Hybrid, hooked to a 1920x1080 display claims to
have a 1024x768 LVDS, and the resulting graphical boot on the 1920x1080
display uses only the top left 1024x768, and auto-configured X will end
up only 1024x768 as well. With this change, graphical boot and X
both do 1920x1080 as expected.

Note that we're simply embracing and extending the early bail-out code
in place for the Mac Mini here. The xorg intel driver uses pci subsystem
device and vendor id for matching, while we're using dmi lookups here.
The MSI addition is courtesy of and tested by Bill Nottingham.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Tested-by: NBill Nottingham <notting@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

We might sleep here anyway so I hope an extra uncached read is ok to
add.

In #20896 we found that vbetool clobbers the IER.  In KMS mode this is
particularly bad since we don't set the interrupt regs late (in
EnterVT), so we'd fail to get *any* interrupts at all after X started
(since some distros have scripts that call vbetool at X startup
apparently).

So this patch checks IER at wait_request time, and re-enables
interrupts if it's been clobbered.  In a proper config this check
should never be triggered.

This is really a distro issue, but having a sanity check is nice, as
long as it doesn't have a real performance hit.
Tested-by: NMateusz Kaduk <mateusz.kaduk@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Moved the check inside of the sleeping case to avoid perf cost]
Signed-off-by: NEric Anholt <eric@anholt.net>

In IGD, DPCUNIT_CLOCK_GATE_DISABLE bit should be set, otherwise i2c
access will be wrong.

v2: Disable CLOCK_GATE_DISABLE bit after bit bashing as suggested by Eric.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This should avoid a class of bugs where the hardware prefetches past the
end of the object, and walks into unallocated memory when the object is
bound to the last page of the aperture.

fd.o bug #21488
Signed-off-by: NEric Anholt <eric@anholt.net>

This makes software fallbacks not do tiling wrong on i965 and later after
resume. It also should fix 945 performance reduction after resume which
would have disabled tiling without causing any visible effect.
Signed-off-by: NKeith Packard <keithp@keithp.com>
[anholt: Fixed up the 915 case to not save/restore the new regs]
Signed-off-by: NEric Anholt <eric@anholt.net>

i386 has inline code for writeq and readq, so just use those instead of ugly
macros which evaluate arguments multiple times.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

A regression was introduced in hg changeset 33810c734a0d, which resulted in
a kernel panic whenever the device was disconnected from USB.  The call to
4l2_device_register() was overwriting the pointer for usb_set_intfdata(), so
when au0828_usb_disconnect() was called, the usb_get_intfdata() returned a
pointer to the v4l2_device instead of the au0828_dev structure.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Two fixes for DViCO FusionHDTV DVB-T Dual Express:

 * Reset correct tuner when reinitializing xc3028.
 * Disable the I2C gate control to avoid locking up the I2C bus.
Tested-by: NJohn Knops <jknops@australiaonline.net.au>
Reviewed-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NChristopher Pascoe <linuxdvb@itee.uq.edu.au>
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

set_modeready flag must be set before command sent to USB in
s2255_write_config.
Signed-off-by: NDean Anderson <dean@sensoray.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

* Return actual error values as returned by the i2c subsystem, rather
  than 0 or 1.
* If the registration of the second bus fails, unregister the first one
  before exiting, otherwise we are leaking resources.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Currently drivers/media drivers are linked very early - directly after
base, block, misc, and mfd and before ata, scsi, ide, input, firewire,
usb, and i2c. This breaks static build of video4linux drivers, that use
generic CPU i2c adapter drivers and the v4l2-subdev subsystem, because
during video4linux probing the v4l2-subdev core requires a struct
i2c_adapter context, which cannot be satisfied before the i2c subsystem is
initialised. Moving drivers/media after drivers/i2c fixes this problem.

The best way to trigger action is by submitting a patch:-) So, let's see
what comes out of it - on the one hand I don't see any reason why media
has to be linked this early, and nobody was able to give me one yesterday
as this problem has been discussed on linux-media, OTOH, maybe indeed it
would be better to move i2c the whole way up above media, but that'd be
much bigger of a change, I think.
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.htmlSigned-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I lowered the kfree(t) down a couple lines and removed the superflous
"t->vdev = NULL;"
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I moved the kfree() down a couple lines.  t->vdev is going to be in freed
memory so there is no point setting it to NULL.  I added a kfree(t) on a
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

selecting ALSA module breaks if !SND. Just remove select.

While here, let's fix the whitespacing at the Kconfig.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A late v4l2_subdev framework change accidentally sent the audio input
routing value to the external multiplexer, instead of the muxer input routing
value to the external multiplexer.  This change corrects that error.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

After experimenting with kexec with the last merges after 2.6.29, I've
had some problems when probing e100.  It would not read the eeprom.  After
some bisects, I realized this has been like that since forever (at least
2.6.18).  The problem is that shutdown is doing the same thing that
suspend does and puts the device in D3 state.  I couldn't find a way to
get the device back to a sane state in the probe function.  So, based on
some similar patches from Rafael J. Wysocki for e1000, e1000e, and ixgbe,
I wrote this one for e100.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: N"Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hd dance around local irq and HD_IRQ enable without achieving much.
It ends up transferring data from irq handler with both local irq and
HD_IRQ disabled.  The only place it actually does something is while
transferring the first block of a request which it does with HD_IRQ
disabled but local irq enabled.

Unfortunately, the dancing is horribly broken from locking POV.  IRQ
and timeout handlers access block queue without grabbing the queue
lock and running the driver in SMP configuration crashes the whole
machine pretty quickly.

Remove meaningless irq enable/disable dancing and add proper locking
in issue, irq and timeout paths.
Signed-off-by: NTejun Heo <tj@kernel.org>

drivers/block/mg_disk.c: In function ‘mg_dump_status’:
drivers/block/mg_disk.c:265: warning: format ‘%ld’ expects type ‘long int’, but
argument 2 has type ‘sector_t’

[ Impact: kill build warning ]

Cc: unsik Kim <donari75@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

IRQ and timeout handlers call functions which expect locked queue lock
without locking it.  Fix it.

While at it, convert 0s used as null pointer constant to NULLs.

[ Impact: fix locking, cleanup ]
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: unsik Kim <donari75@gmail.com>

Default voltage constraints were being provided for fixed voltage
regulator where board constraints were not provided but these constraints
used INT_MIN as the default minimum voltage which is not a valid value
since it is less than zero. Use 1uV instead.

Also set the default values we set in the constraints themselves since
otherwise the max_uV constraint we determine will not be stored in the
actual constraint strucutre and will therefore not be used.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This seems to be fallout from last October's regulator core rework.
It got noticed only because of recent regulator framework changes.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

During regulator registration, any error after device_register() will
cause a double-free on the struct regulator_dev 'rdev'.  The bug is in
drivers/regulator/core.c:regulator_register():

...
scrub:
	device_unregister(&rdev->dev);
clean:
	kfree(rdev);                           <---
	rdev = ERR_PTR(ret);
	goto out;
...

device_unregister() calls regulator_dev_release() which frees rdev.  The
subsequent kfree corrupts memory and causes some OMAP3 systems to oops on
boot in regulator_get().

Applies against 2.6.30-rc3.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

When regulator_desc->type is something different from REGULATOR_VOLTAGE or REGULATOR_CURRENT
the if should probably return ERR_PTR(-EINVAL)

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

@@ expression E; constant C; @@
(
- !E == C
+ E != C
)
Signed-off-by: NDiego Liziero <diegoliz@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

I removed the extra semi-colon and indented the return statement.

The unreachable code was found by smatch (http://repo.or.cz/w/smatch.git).
The patch was compile tested.

regards,
dan carpenter
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Update version number to 1.5.0.0
Signed-off-by: NChien Tung <chien.tin.tung@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

If reg_phys_mem() fails, we need to free memory allocated for MPA
frame with private data before returning the error. Also move
nes_add_ref() after the reg_phys_mem() is successful.
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Running large cluster setup, we are hanging after many hours of
testing.  Fixing this required going over the code and making sure the
rexmit entry was properly removed based on the cm_node's state and
packet received.  Also when receiving a FIN packet, check seq# and
make sure there were no errors before calling handle_fin().

Following are the changes done in nes_cm.c:

* handle_ack_pkt() needs to return error value, so in case of error,
  handle_fin() is not called. Some cleanup done while going over the code.

* handle_rst_pkt(), handling of cm_node's NES_CM_STATE_LAST_ACK is missing.

* process_packet(), in case of FIN only packet is received, call
  check_seq() before processing.

* in handle_fin_pkt(), we are calling cleanup_retrans_entry() for all
  conditions, even if the packets need to be dropped.
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Under heavy load with large cluster testing, it may take longer to
receive a response to MPA requests.  Change the driver to wait longer
after each rexmit to max time value.
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

check_seq() was not checking if the seq#s have wrapped.  Fix it.
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When a connect request comes, apbvt should only be set for
non-loopback connections.
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove the NES_DEBUG that is causing the compile warning about an
unused variable when INFINIBAND_NES_DEBUG is not enabled.
Signed-off-by: NChien Tung <chien.tin.tung@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

/sys/class/infiniband/nes?/fw_ver is not displaying firmware version
properly (it shows 0.0.0 with the current code).  Fill in the correct
firmware version number.
Signed-off-by: NChien Tung <chien.tin.tung@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

With updated PHY firmware for SFP_D, setting the trace length to 1
inch for SFP_D provides a more stable link.
Signed-off-by: NChien Tung <chien.tin.tung@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Enable repause timer for port 1.  Without this setting, under stress,
the chip may misbehave.
Signed-off-by: NChien Tung <chien.tin.tung@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In commit 1b949324 ("RDMA/nes: Fix SFP+ PHY initialization") there is
a mistake in the clean up code that removed port 1 CDR loop filter
settings for 10G cards other than CX4.  Put the correct setting back
for appropriate PHY types.
Signed-off-by: NChien Tung <chien.tin.tung@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Change thermo mitigation code to flip the SerDes1 reference clock to
internal, to match the change in commit a4849fc1 ("RDMA/nes: Add
wide_ppm_offset parm for switch compatibility").
Signed-off-by: NChien Tung <chien.tin.tung@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This reverts commit 8032b526.

Hey, it was only meant to be a single release.  Now they can all die as
far as I'm concerned.

[ Just kidding.  They're cute and cuddly.

  Except when they have horrible nasty facial diseases.  Oh, and I guess
  they're not actually that cuddly even when disease-free. ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

isdn: document Kernel CAPI driver interface

Create a file Documentation/isdn/INTERFACE.CAPI describing the
interface between the kernel CAPI subsystem and ISDN device drivers,
analogous to the existing Documentation/isdn/INTERFACE for the old
isdn4linux subsystem. Also add kerneldoc comments to the exported
functions in drivers/isdn/capi/kcapi.c.

Impact: Documentation
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>