A new sysfs shost attribute called "BMR_status" is implemented to report
Backup Rail Monitor status.

This attribute is located in:

        /sys/class/scsi_host/host#/BMR_status

When reading this adapter attribute, the driver will output the state of
GPIO[24]. It returns "0" if BMR is healthy and "1" for failure.

If it returns an empty string then it means that there was an error
while obtaining the BMR status. Check dmesg for what error has occurred.

This sysfs shost attribute is mainly for WarpDrive controllers.

This commit is a port of 6c265660 ("mpt2sas: Provide sysfs attribute
to report Backup Rail Monitor Status").
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Ported the following list of WarpDrive-specific patches:

1. commit 0bdccdb0 ("mpt2sas: WarpDrive
   New product SSS6200 support added")

2. commit 82a45258 ("mpt2sas: WarpDrive
   Infinite command retries due to wrong scsi command entry in MPI
   message")

3. commit ba96bd0b ("mpt2sas: Support
   for greater than 2TB capacity WarpDrive")

4. commit 4da7af94 ("mpt2sas: Do not
   retry a timed out direct IO for Warpdrive")

5. commit daeaa9df ("mpt2sas: Avoid type
   casting for direct I/O commands").

Also set the mpt2_ioctl_iocinfo adapter_type to:

1. MPT3_IOCTL_INTERFACE_SAS3 for Gen3 HBAs

2. MPT2_IOCTL_INTERFACE_SAS2_SSS6200 for Warp Drive

3. MPT2_IOCTL_INTERFACE_SAS2  for other Gen2 HBAs
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch stops the driver to invoke kthread (which remove the dead
ioc) for some time while EEH recovery has started.

This patch is a port of commit b4730fb6 ("mpt2sas: fix for driver
fails EEH, recovery from injected pci bus error")'.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1. Do not enable MSI-X vectors for SAS2008 B0 controllers

2. Enable a single MSI-X vector for the following controller:

   a. SAS2004
   b. SAS2008
   c. SAS2008_1
   d. SAS2008_2
   e. SAS2008_3
   f. SAS2116_1
   g. SAS2116_2

3. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
   for Gen3 Invader/Fury C0 and above revision HBAs

4. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
   for all Intruder and Cutlass HBAs
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1. Use 'hba_mpi_version_belonged' IOC varable to uniquely identify each
individual generation driver functionality at runtime.

2. Declare global variable 'driver_name' and use this variable while
reserving PCI regions and while allocating the IRQs.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Created a mpt3sas_module.c file for mpt3sas driver where it can register
SAS3 HBA devices with PCI, SML, IOCTL subsystems. Also removed the
corresponding interfaces from mpt3sas_scsih.c file.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1. Added mpt2sas driver related macros in mpt3sas header files

2. Made scsi host's, raid class', pci's, ioctl's callback functions
global so that both drivers can use them.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

"VendorID"   "DeviceID"  "SubsystemVendor ID"   "SubsystemDevice ID"  Cisco Branding String
0x1000         0x97           0x1137                 0x154           Cisco 9300-8i 12Gbps SAS HBA
0x1000         0x97           0x1137                 0x155           Cisco 12G Modular SAS Pass through Controller
0x1000         0x97           0x1137                 0x156           UCS C3X60 12G SAS Pass through Controller
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

For any SCSI command, if the driver receives
IOC status = SCSI_IOC_TERMINATED and log info = 0x32010081 then
that command will be completed with DID_RESET host status.

The definition of this log info value is
"Virtual IO has failed and has to be retried".

Firmware will provide this log info value with IOC Status
"SCSI_IOC_TERMINATED", whenever a drive (with is a part of a volume)
is pulled and pushed back within some minimal delay.
With this log info value, firmware informs the driver to retry the
failed IO command infinite times, so to provide some time for the
firmware to discover the reinserted drive successfully instated of
just retrying failed command for five times(doesn't giving enough
time for firmware to complete the drive discovery) and failing the
IO permanently even though drive came back successfully.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Add the following OEM's branding to the mpt3sas driver.

"VendorID"   "DeviceID"  "SubsystemVendor ID"   "SubsystemDevice ID"  Cisco Branding String
0x1000         0x97         SVID = 0x1137             0x014C          Cisco 9300-8E 12G SAS HBA
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Added the following Dell branding to the mpt3sas driver.

"VendorID"   "DeviceID"  "SubsystemVendor ID"  "SubsystemDevice ID"  Dell Branding String
0x1000        0x0097          0x1028                 0x1F46            DELL 12Gbps HBA
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

This Patch will provide more details of the devices such as slot number,
enclosure logical id, enclosure level & connector name in the following
scenarios,

- When end device is added in the topology,

- When the end device is removed from the setup,

- When the SCSI mid layer issues TASK ABORT/ DEVICE RESET/ TARGET RESET during
  error handling,

- When any command to the device fails with Sense key Hardware error or Medium
  error or Unit Attention,

- When firmware returns device error or device not ready status for the end
  device,

- When a Predicted fault is detected on an end device.

This information can be used by the user to identify the location of the
desired drive in the topology.

Driver will get these information by reading the sas device page0.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

During hot-plugging of a disk(having a flaky link), the disk addition
stops and any further disk addition or removal doesn't happen on that
controller.

This is because, when driver receives DELAY_NOT_RESPONDING event for a disk
while it is undergoing addition at the SCSI Transport layer, the driver
would block the I/O to that disk resulting in a deadlock. i.e the disk
addition work couldn't be completed at the SCSI Transport Layer as it
can't send any I/Os (such as Inquiry, Report LUNs etc) to the disk as
I/Os are blocked to this drive. Also any subsequent device removal
(TARGET_NOT_RESPONDING) or link update(RC_PHY_CHANGED) event couldn't be
processed as they are in the queue to get processed after disk addition
event.

Description of Change:
Don't block the drive when drive addition is under the control of SML.
So that SML won't be blocked of issuing the device dicovery commands
(such as Inquiry, Report LUNs etc).
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

In this patch, increased the number of MSIX vector support for SAS3 C0 HBAs to
up-to 96.

Following are changes that are done in this patch

1. This feature is enabled only for SAS3 C0 and higher revision cards and also
only when reply post free queue count is greater than 8.

2. To support this feature 12 SupplementalReplyPostHostIndex system interfaces
are used. MSI-X index numbered from 0 to 7 use the first
SupplementalReplyPostHostIndex system interface to update its corresponding
ReplyPostHostIndex values, MSI-X index numbered from 8 to 15 will use the
second SupplementalReplyPostHostIndex system interface and so on. These 12
SuppementalReplyPostHostIndex system interfaces address are saved in the array
replyPostRegisterIndex[].

3. As each SupplementalReplyPostHostIndex register supports 8 MSI-X
vectors. So MSIxIndex field in these register must contain a value between 0
and 7.

4. After processing the reply descriptors from a reply post free queues then
update the new reply post host index value in ReplyPostHostIndex field and
(msix_index mod 8) value in MSIxIndex field of SupplementalReplyPostHostIndex
register. The Address of this SupplementalReplyPostHostIndex register is
retrived from (msix_index/8)th entry of replyPostRegisterIndex[] array.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Added a support to set cpu affinity mask for each MSIX vector enabled
by the HBA. So that, running the irqbalancer will balance interrupts among
the cpus.

Change_set:
1. Added affinity_hint varable of type cpumask_var_t in adapter_reply_queue
   structure. And allocated a memory for this varable by calling
   alloc_cpumask_var.
2. Call the API irq_set_affinity_hint for each MSIx vector to affiniate it
   with calculated cpus at driver inilization time.
3. While freeing the MSIX vector, call this same API to release the cpu
   affinity mask for each MSIx vector by providing the NULL value in
   cpumask argument.
4. then call the free_cpumask_var API to free the memory allocated in step 2.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Copyright, Trademark & Confidentiality legal statements throughout the
source code changed from LSI to Avago.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch will log a message when driver receives "Temperature Threshold
exceeded" event from any temperature sensor.

The message will look similar to like:
mpt3sas0: Temperature Threshold flags a b c d exceeded for Sensor: x !!!
mpt3sas0: Current Temp In Celsius: y

where a b c d are threshold flags 0 1 2 3

Change_set:
1. Get the number of sensor count of this IOC by reading IO Unit page 8 at
   driver initialization time.
2. Also unmask the Temperature Threshold Event at driver initialization
   time
3. Whenever a MPI2_EVENT_TEMP_THRESHOLD event is received from the
   firmware, then print the sensor number, the maximum threshold number it
   has exceed and the current temperature of this sensor.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Bump mpt3sas driver version to 04.100.00.00.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Up to now, Driver allocates a single contiguous block of memory
pool for all reply queues and passes down a single address in the
ReplyDescriptorPostQueueAddress field of the IOC Init Request
Message to the firmware.

When firmware receives this address, it will program each of the
Reply Descriptor Post Queue registers, as each reply queue has its
own register. Thus the firmware, starting from a base address it
determines the starting address of the subsequent reply queues
through some simple arithmetic calculations.

The size of this contiguous block of memory pool is directly proportional
to number of MSI-X vectors and the HBA queue depth. For example higher
MSIX vectors requires larger contiguous block of memory pool.

But some of the OS kernels are unable to allocate this larger
contiguous block of memory pool.

So, the proposal is to allocate memory independently for each
Reply Queue and pass down all of the addresses to the firmware.
Then the firmware will just take each address and program the value
into the correct register.

When HBAs with older firmware(i.e. without RDPQ capability) is used
with this new driver then the max_msix_vectors value would be set
to 8 by default.

Change set in v1:

1. Declared the _base_get_ioc_facts() functions at the beginning of the mpt3sas_base.c file
instead of moving all these functions before mpt3sas_base_map_resources() function
        a. _base_wait_for_doorbell_int()
        b. _base_wait_for_doorbell_ack()
        c. _base_wait_for_doorbell_not_used()
        d. _base_handshake_req_reply_wait()
        e. _base_get_ioc_facts()

2. Initially set the consistent DMA mask to 32 bit and then change it to 64 bit mask
after allocating RDPQ pools by calling the function _base_change_consistent_dma_mask.
This is to ensure that all the upper 32 bits of RDPQ entries's base address to be same.

3. Reduced the redundancy between the RDPQ and non-RDPQ support in these following functions
        a. _base_release_memory_pools()
        b. _base_allocate_memory_pools()
        c. _base_send_ioc_init()
        d. _base_make_ioc_operational()
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Added following branding Strings for Intel custom HBAs support.

Driver String:                                  Vendor ID       Device ID       SubSystemVendor ID      SubSystemDevice ID
Intel(R) Integrated RAID Module RMS3JC080       0x1000          0x0097          0x8086                  0x3521
Intel(R) RAID Controller RS3GC008               0x1000          0x0097          0x8086                  0x3522
Intel(R) RAID Controller RS3FC044               0x1000          0x0097          0x8086                  0x3523
Intel(R) RAID Controller RS3UC080               0x1000          0x0097          0x8086                  0x3524
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Copyright in driver sources is updated for year the 2014.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Bump mpt3sas driver version to 03.100.00.00.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Added code to send an SEP message that turns off the Predictive
Failure LED when a drive is removed (if Predictive Failure LED was turned on).

Added a new flag 'pfa_led_on' per device that tracks the status of Predictive
Failure LED. When the drive is removed, this flag is checked and
sends an SEP message to turn off the respective Predictive Failure LED.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The mpt3sas_scsih_issue_tm() function does not use the 'serial_number'
argument passed to it.  Removing it removes the last vestiges of the
scsi_cmnd's serial_number field from this driver.
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: NNicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: NPraveen Krishnamoorthy <Praveen.krishnamoorthy@lsi.com>
Acked-by: NSreekanth Reddy <Sreekanth.reddy@lsi.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Bump driver version to v02.100.00.00.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The Copyright String in all mpt3sas files are changed to 2012-2013.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

These driver files are initially, substantially similar to mpt2sas but,
because mpt2sas is going into maintenance mode and mp3sas will become heavily
developed, we elected to keep the code bases separate.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Reviewed-by: NNagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NSreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

A new sysfs shost attribute called "BMR_status" is implemented to
report Backup Rail Monitor status.

This attribute is located in the path
        /sys/class/scsi_host/host#/BMR_status

when reading this adapter attribute, then driver will output the state
of GPIO[24]. It returns "0" if BMR is healthy and it returns "1" for failure.

if it returns an empty string then it means that there was an error while
obtaining the BMR status. Then check dmesg for what error has occured.
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Updating the customer branding string for "SSD 910 Series" controller
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The Copyright String in all the drivers sources were changed to 2012
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This has scsi_internal_device_unblock/scsi_target_unblock take
the new state to set the devices as an argument instead of
always setting to running. The patch also converts users of these
functions.

This allows the FC and iSCSI class to transition devices from blocked
to transport-offline, so that when fast_io_fail/replacement_timeout
has fired we do not set the devices back to running. Instead, we
set them to SDEV_TRANSPORT_OFFLINE.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: Improvement were made to better protect the sas_device, raid_device, and expander_device lists

There were possible race conditions surrounding reading an object
from the link list while from another context in the driver was
removing it. The nature of this enhancement is to rearrange locking
so the link lists are better protected.

Change set:
(1) numerous routines were rearranged so spin locks are held through
the entire time a link list object is being read from or written to.
(2) added new routines for object deletion from link list.  Thus ensuring
lock was held during the deletion of the link list object, then and memory
for object freed outside the lock. The memory was freed outside the lock
so driver had access to device object info which was required for
notifying the scsi mid layer that a device was getting deleted.
(3) added the ioc->blocking_handles parameter.  This is a bitmask used
to identify which devices need blocking when there is device loss.  This was
introduced so that lock can be held for the entire time traversing the link
list objects, and the bitmask was set to indicate which device handles need
blocking. Oustide the lock the ioc->blocking_handles bitmask is traversed,
with the respective device handle the scsi mid layer is called for moving
devices into blocking state.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Bump driver vesion to 12.100.00.00
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>