This device stores the number of seconds in a 32 bit register, and the
stored value is unsigned.  Therefore this driver and device are ready
for the year 2038.  However, more work will be needed prior to 2106.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit ae5c6c6d "ptp: Classify ptp over ip over vlan packets" changed the
code in two drivers that matches time stamps with PTP frames, with the goal
of allowing VLAN tagged PTP packets to receive hardware time stamps.

However, that commit failed to account for the VLAN header when parsing
IPv4 packets. This patch fixes those two drivers to correctly match VLAN
tagged IPv4/UDP PTP messages with their time stamps.

This patch should also be applied to v3.17.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that dp83640_remove can use skb_queue_purge
instead of looping through itself to flush any entries out of the queue.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy timestamping takes a different path than the regular timestamping
does in that it will create a clone first so that the packets needing to be
timestamped can be placed in a queue, or the context block could be used.

In order to support these use cases I am pulling the core of the code out
so it can be used in other drivers beyond just phy devices.

In addition I have added a destructor named sock_efree which is meant to
provide a simple way for dropping the reference to skb exceptions that
aren't part of either the receive or send windows for the socket, and I
have removed some duplication in spots where this destructor could be used
in place of sock_edemux.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Event timestamp status messages have a variable length, ranging from
1 to 5 words (16 bit words). The current code however requires
a minimum message length of sizeof(*phy_txts). In most cases this
condition is fulfilled due to padding bytes. However, if several events
are signaled in a single message, padding bytes may not be present.
For short event timestamp status messages, the length check will fail,
and the event timestamp will be dropped.
Signed-off-by: NChristian Riesch <christian.riesch@omicron.at>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When timestamping received packets, rx_timestamp_work may be scheduled
before the timestamps is received from the hardware resulting in the
packet beeing delivered without the timestamp.

This is fixed by changing the receive timestamp path:

On receiving a packet that need timestamping, the rxts list is
traversed.  If a match is found, packet+timestamp are delivered,
otherwise the packet is added to a rx_queue.

When a timestamp arrives rx_queue is traversed and if a matching
packet is found, it is delivered with the timestamp. Otherwise the
timestamp is added to the rxts list for matching with packets arriving
later.

In case the hardware drops a timestamp, a workqueue regularly checks
the queue for old packets and delivers them without a timestamp.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

  Event timestamp values should be adjusted by 3*reference clock period +
  11 ns = 35 ns to compensate for input path and synchronization delays.

So subtract 35ns from event timestamps.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently status frames are only handled when packet timestamping is
enabled, but status frames are also needed for pin event timestamping.

Fix by moving packet timestamping check to after status frame decode.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This extends the ptp bpf to also match ptp over ip over vlan packets. The ptp
classes are changed to orthogonal bitfields representing version, transport
and vlan values to simplify matching.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For consistency, use the ptp_find_pin function to get the calibration pin,
not gpio_tab.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This constraints the pin assignment to not allow the calibration function to
be reassigned and only allow reassigning the calibratin pin if only one phy is
connected.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch increases the number of supported periodic output pins from
1 to 7. The last pin is reserved for sync.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Periodic output triggers 0 and 1 of the dp83640 has a programmable
duty-cycle which is controlled by the Pulsewidth2 field of the trigger
data register.  This field is not documented in the datasheet, but it
is described in the "PHYTER Software Development Guide" section
3.1.4.1. Failing to set the field can result in unstable/no trigger
output.

Add programming of the Pulsewidth2 field, setting it to the same value
as the Pulsewidth field for a 50% duty cycle.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit fixes a build error reported by Fengguang, that is
triggered when CONFIG_NETWORK_PHY_TIMESTAMPING is not set:

  ERROR: "ptp_classify_raw" [drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe.ko] undefined!

The fix is to introduce its own file for the PTP BPF classifier,
so that PTP_1588_CLOCK and/or NETWORK_PHY_TIMESTAMPING can select
it independently from each other. IXP4xx driver on ARM needs to
select it as well since it does not seem to select PTP_1588_CLOCK
or similar that would pull it in automatically.

This also allows for hiding all of the internals of the BPF PTP
program inside that file, and only exporting relevant API bits
to drivers.

This patch also adds a kdoc documentation of ptp_classify_raw()
API to make it clear that it can return PTP_CLASS_* defines. Also,
the BPF program has been translated into bpf_asm code, so that it
can be more easily read and altered (extensively documented in [1]).

In the kernel tree under tools/net/ we have bpf_asm and bpf_dbg
tools, so the commented program can simply be translated via
`./bpf_asm -c prog` where prog is a file that contains the
commented code. This makes it easily readable/verifiable and when
there's a need to change something, jump offsets etc do not need
to be replaced manually which can be very error prone. Instead,
a newly translated version via bpf_asm can simply replace the old
code. I have checked opcode diffs before/after and it's the very
same filter.

  [1] Documentation/networking/filter.txt

Fixes: 164d8c66 ("net: ptp: do not reimplement PTP/BPF classifier")
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jiri Benc <jbenc@redhat.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver use the new pin configuration method when
programming the periodic output signal.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver to use the new pin configuration method when
programming the external time stamp input signals.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adapts the dp83640 driver to allow reconfiguration of which
auxiliary function goes on which pin. The functions may be reassigned
freely with the one exception of the calibration function.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phyter driver incorrectly feeds the value of the period into what
is in fact a pulse width register, resulting in the actual period
being twice the dialed value. This patch fixes the issue and renames a
variable to make the code at bit more clear.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleans up the input checking code on the external time stamp
function by using an unsigned rather than a signed channel index.

Also, this patch corrects the author's email address. When this macro
was last changed, the top level domain part of the email address was
left behind.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phy_init_hw not does a full PHY reset after the driver probe has
finished, so any hw initialization done in the probe will be lost.
Part of the timestamping functionality of the dp83640 is set up in the
probe and with that lost, enabling timestamping will cause a PHY
lockup, requiring a hard reset / power cycle to recover.

This patch moves all the HW initialization in dp83640_probe to
dp83640_config_init.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The trigger and events functionality can be useful even if packet
timestamping is not used, but the required PTP clock is only enabled
when packet timestamping is started. This patch moves the clock enable
to when the interface is configured.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the external timestamping code is hardcoded to use the
rising edge even though the hardware has configurable event edge
detection. This patch changes the code to use falling edge detection
if PTP_FALLING_EDGE is set in the user supplied flags.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the SKBTX_IN_PROGRESS bit in tx_flags dp83640_txtstamp when doing
tx timestamps as per Documentation/networking/timestamping.txt.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added functions for ack_interrupt and config_intr. Tested on an mpc5200b
powerpc board.
Signed-off-by: NStephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PTP Hardware Clock devices appear as class devices in sysfs. This patch
changes the registration API to use the parent device, clarifying the
clock's relationship to the underlying device.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a more current logging style.

Add pr_fmt and missing newlines.
Remove embedded prefixes.
Neaten phy_print_status to avoid using KERN_CONT.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit brings the author email address macros up to date for four
modules in the PTP Hardware Clock subsystem.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar problem as in 481a8199 ("can:
fix NOHZ local_softirq_pending 08 warning"). This fix replaces
netif_rx() with netif_rx_ni() which has to be used from
process/softirq context.
Signed-off-by: NManfred Rudigier <manfred.rudigier@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the PHY should disappear (for example, on an USB Ethernet MAC), then
the driver would leak any undelivered time stamp packets. This commit
fixes the issue by calling the appropriate functions to free any packets
left in the transmit and receive queues.

The driver first appeared in v3.0.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The previous commit enforces a new rule for handling the cloned packets
for transmit time stamping. These packets must not be freed using any other
function than skb_complete_tx_timestamp. This commit fixes the one and only
driver using this API.

The driver first appeared in v3.0.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver has two warning messages that might be triggered
by normal use cases. When they appear, the messages give the
impression of a never ending series of errors.

This commit changes them to debug messages instead.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds one step support to the phyter. When enabled, the
hardware does not provide time stamps for transmitted sync messages but
instead inserts the stamp into the outgoing packet.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables six external event channels and one periodic output.
One GPIO is reserved for synchronizing multiple PHYs. The assignment
of GPIO functions can be changed via a module parameter.

The code supports multiple simultaneous events by inducing a PTP clock
event for every channel marked in the PHY's extended status word.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dp83640 buffers receive time stamps from special PHY status frames,
matching them to received PTP packets in a work queue. Because the timeout
for orphaned time stamps is so long and the buffer is so small, the driver
can drop time stamps under moderate PTP traffic.

This commit fixes the issue by decreasing the timeout to (at least) one
timer tick and increasing the buffer size.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Cc: <stable@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dp83640 PHY provides time stamp and other information via special
PHY status frames. Previously, the driver decoded the frames and then
let the network stack drop them. This works fine when the PTP messages
come over UDP.

However, when receiving PTP messages via L2 packets, this creates a
problem. The status frames use the official PTP destination MAC address,
and so they are delivered to user space along with the "real" frames,
causing confusion for applications.

This commit fixes the issue by simply dropping the PHY status frames
in the driver.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

If two eternal time stamp events occur at nearly the same time, the
phyter will add an extra word into the status frame. This commit fixes
the parsing code to recognize and skip over the extra word.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

If the dp83640 driver is not built as a module, the
MODULE_DEVICE_TABLE reference to dp83640_tbl nops out.

Since the table isn't referenced elsewhere, it it causes
the following warning:
drivers/net/phy/dp83640.c:1095: warning: ‘dp83640_tbl’ defined but not used

This apparently is common with mdio_device_id table structures,
and is avoided by using __maybe_unused annotation.
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

This patch adds support for the PTP clock found on the DP83640.
The basic clock operations and one external time stamp have
been implemented.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>