The SKY2_HW_RAM_BUFFER bit in hw->flags was checked in sky2_mac_init(),
 before being set later in sky2_up().

Setting SKY2_HW_RAM_BUFFER in sky2_init() where other hw->flags are set
 should avoid this problem recurring.
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Sorry Mike, I sent you off the wrong way. The following is simpler and the
second port is diffrent enough in setup (because of NAPI), that the
following is simpler.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Be more accurate about number of transmit list elements required.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While perusing vendor driver, I saw that it did not enable the Vaux
power unless device was able to wake from lan for D3cold.
This might help for Rene's power issue.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

B0_CTST is a 24bit register according to the vendor driver (sk98lin).
A 16bit read on B0_CTST will always return 0 for Y2_VAUX_AVAIL (1<<16),
 so use a 32bit read when testing Y2_VAUX_AVAIL
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor similar two sections of code that free buffers into one.
Only call tx_init if all buffer allocations succeed.
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Observed by Mike McCormack.

The LED bit here is just a software controlled value used to
turn on one of the LED's on some boards. The register value was wrong,
which could have been causing some power control issues.
Get rid of problematic define use the correct mask.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a couple of cases collapse some extra code like:
   int retval = NETDEV_TX_OK;
   ...
   return retval;
into
   return NETDEV_TX_OK;
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recycling turns out to be a bad idea!  For most use cases, the
packet can not be reused: TCP packets are cloned. Even for the ideal
case of forwarding, it hurts performance because of CPU ping/pong.
On a multi-core system forwarding of 64 byte packets is worse
much worse: recycling = 24% forwarded vs no recycling = 42% forwarded
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't reference the list element in hardware transmit ring on transmit
completion. The list element is updated by hardware, therefore
it causes a cache miss. Do book keeping in software structure.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate and size transmit ring based on parameters. Saves excess
space and allows configuring larger rings for testing.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code for list element error (which should only happen on hardware
errors) should be cleaner and safer. Gets rid of unused ring_size
argument, which makes next patch easier.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch saves elements on transmit ring by only updating the upper
64 bit address when it changes. With many workloads skb's are located
in same region, so it saves space.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the existing macros to show where DMA address is being broken
apart. This is cosmetic only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The whole restarting flag was introduced by Mike McCormack
and was a temporary duct tape patch around issues with transmits
inflight during restart. The problems it was covering are now
fixed and the code should have been reverted.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sky2 driver combines auto speed negotiation with automatic negotiation
of pause parameters; but the ethtool interface expects them to be
split. This patch allows autonegotiation to be used for speed, but
manually disable flow control.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Transmit completion can safely run lockless against transmit start.
In the normal case, completion is done from NAPI and only looks
at elements that are at the tail of the ring.  When doing shutdown
or reset, the transmiter should be completely block by NAPI disable
and blocking of transmit queue. 

Based on earlier work by Mike McCormack.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This unifies the places that bounce the device (suspend/resume
and restart). And makes the operations have the same semantics
as normal dev_open/dev_stop.

This also avoids setting the multicast addresses twice when
device is brought up.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The suspend and shutdown code plays with shared state. Use consistent
locking, for extra protection.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid any possible problems with accessing PHY registers on shutdown.
This is a purely theoretical issue and is not related to any of the
outstanding bug reports. Since receiver and transmitter are already
shutdown and phy interrupts for this device are already disabled,
there should already be enough protection. Suggested by Mike McCormack.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reseting the tx chain too soon results in invalid tx queue positions
being delivered in the status queue.  This also makes sure there's no
overlap between the cleanup done by sky2_tx_clean() and
sky2_tx_done().
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is pure refactoring.
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Keep sky2->tx_prod consistent since int might be examined by
an softirq poll or restart.
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch supersedes my previous patch "sky2: Avoid transmitting
during sky2_restart".

I have reworked the patch to avoid crashes during both sky2_restart()
and sky2_set_ringparam().

Without this patch, the sky2 driver can be crashed by doing:

# pktgen eth1 &    (transmit many packets on eth1)
# ethtool -G eth1 tx 510

I am aware you object to storing extra state, but I can't see a way
around this. Without remembering that we're restarting,
netif_wake_queue() is called in the ISR from sky2_tx_complete(), and
netif_tx_lock() is used in sky2_tx_done().  If anybody can see a way
around this, please let me know.
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMike McCormack <mikem@ring3k.org>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reset rx chain before trying to drain it.
Shut interrupts off last, incase there's something to report.
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit changes to shutdown path broke startup on some systems.

revert commit c0bad0f2Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sky2 driver on PowerPC targets floods kernel log with following errors:

  eth1: hw csum failure.
  Call Trace:
  [ef84b8a0] [c00075e4] show_stack+0x50/0x160 (unreliable)
  [ef84b8d0] [c02fa178] netdev_rx_csum_fault+0x3c/0x5c
  [ef84b8f0] [c02f6920] __skb_checksum_complete_head+0x7c/0x84
  [ef84b900] [c02f693c] __skb_checksum_complete+0x14/0x24
  [ef84b910] [c0337e08] tcp_v4_rcv+0x4c8/0x6f8
  [ef84b940] [c031a9c8] ip_local_deliver+0x98/0x210
  [ef84b960] [c031a788] ip_rcv+0x38c/0x534
  [ef84b990] [c0300338] netif_receive_skb+0x260/0x36c
  [ef84b9c0] [c025de00] sky2_poll+0x5dc/0xcf8
  [ef84ba20] [c02fb7fc] net_rx_action+0xc0/0x144

The NIC is Yukon-2 EC chip revision 1.

Converting checksum field from le16 to CPU byte order fixes the issue.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Version bump.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for generic receive offload.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements skb recycling. It reclaims transmitted skb's
for use in the receive ring.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce the size of the driver transmit ring to reduce latency
and allow qdisc to do better rate control.  Also make it
obvious what the minimum transmit ring allowed is and why.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since it is likely that there are multiple packets received per
interrupt, only update the receive counters once after all
packets are processed.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The logic in sky2_down was incorrect. Receiver could report status
after rx_stop was called.

The steps need to be:
   * stop new frames from being transmitted
   * shut off transmit/receive logic
   * synchronize with NAPI to process status info about transmitter
     and receiver
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add some read's to avoid any PCI posting issues when controlling
irq's.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reset more parts of the receive path when device is take offline.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>