The generic fbcon code tries to register and use the vsync IRQ for
ARM platforms with acornfb, but forgets to disable its own cursor
timer.  The result is a flickering flashing cursor.

Remove the code from the fbcon core to register this platform
private interrupt.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If we receive an unrecognised abort during boot, don't try to
send a signal to pid0, but instead report the current state.
This leads to less confusing debug reports.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The following patch enables attrs by default if the reiserfs_attrs_cleared
bit is set in the superblock.  This allows chattr-type attrs to be used
without any further action by the user.
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

ReiserFS currently will allow the user to set/get attrs for files
regardless if they are enabled.  The patch checks to see if they are
enabled, and returns -NOTTY if they are not.

ext[23] doesn't need this check because attrs are always enabled.
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NTony Luck <tony.luck@intel.com>

Signed-off-by: NTony Luck <tony.luck@intel.com>

We were forcing SIGFPE on to a user program for no good reason.
Use send_sig_info() instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

VFP used __divdi3 64-bit division needlessly.  Convert it to use
our 64-bit by 32-bit division instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Tony Lindgren

This patch adds support for Dynamic Tick Timer for OMAP.
This patch is an updated version of ARM patch 2642/1 to
make it work with the already integrated generic ARM
dyntick support.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove legacy ISA serial ports for Accent, Boca, Fourport, Hub6 and MCA
from the architecture specific serial.h include.

The only ports which remain in asm-*/serial.h are the platform specific
entries.  These should really be converted by platform maintainers to
use a platform device, such as can be found in
arch/arm/mach-footbridge/isa.c
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Disable the transmitter whenever we want to prevent characters
being transmitted by flow control.  However, if we run out of
characters to send and want to only disable the TX interrupt,
allow that scenario.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix bugme #4712: read the CTS status and set hw_stopped if CTS
is not active when opening the port and/or enabling CRTSCTS

Thanks to Stefan Wolff for spotting this problem.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The nmi watchdog code hasn't been merged for this platform yet.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

Those are big, slow and generally not recommended for kernel code.
They are even not present on i386.  So it should be concluded that
one could as well get away with do_div() alone.
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

I am using the atxp1 module to change vcore on my NForce2 via userspace
daemon (see punnoor.de).

Currently the atxp1 module will write to the log on every vcore change,
thus filling up my log - which I don't want.  I am no kernel coder, but
I guess, this one-liner will change this behaviour in a wanted way, ie
output will be made for debug purposes only.
Signed-off-by: NPrakash Punnoor <prakash@punnoor.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

get_request is now expected to be holding on to queue_lock, with interrupts
disabled, when it returns NULL; but one path forgot that, causing all kinds
of nastiness under swap load - badness backtraces, strange failures, BUGs.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Patch from Catalin Marinas

The compiler allocates r14 for the stk variable in the __asm__ directive.
This is a shadowed register and gets changed when the mode is changed,
causing random values in the SP register. The patch adds a clobber for
the r14 register.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Richard Purdie

With DEBUG enabled, head.S includes arch/debug-macro.S. On the PXA, this
contains references to the macro io_p2v() so hardware.h needs to be
included.
Signed-off-by: NRichard Purdie <rpurdie@openedhand.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Convert ARMs timer implementations to use readl/writel instead of accessing
the registers via a struct.

People have recently asked if accessing timers via a structure is the
"right way" and its not the Linux way.  So fix this code to conform to
"The Linux Way"(tm).
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>

Patch from Ben Dooks

Re-tab the devs.c file, and change the initialiser for the
mach-vr1000.c to use `.xxx = yyy` form.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

All current S3C24XX implementations from Simtec share the same
requirements for suspend/resume information.
This patch moves the save code out of the mach-bast.c file,
and into it's own so it can be shared by all the current
Simtec S3C24XX implementations.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch changes the way serial ports are locked when getting modem
status.  This change is necessary because we will need to atomically
read the modem status and take action depending on the CTS status.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Ok, a lot of things were pending after the 2.6.12 release, let's try to
start calming things down again.

This crept in with the resync-to-mainline.  Nothing uses 802.11-crypt in
mainline, so we can safely comment it out for now.
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch adds the SiS 760 ID to the amd64-agp driver, so that agpgart can be
used on Athlon64 boards based on this chip.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Something reverted most of the arch/sparc/Kconfig changes, leaving
arch/sparc/ unconfigurable.  This patch re-removes the parts made redundant
by drivers/Kconfig in addition to a mysterious, spurious second instance of
source "mm/Kconfig".  cvs strikes again?
Signed-off-by: NWilliam Irwin <wli@holomorphy.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Corrections to Documentation/Submitting{Drivers,Patches}
- update LANANA info.
- fix some typos
- update 2.2 kernel maintainer info.
- update 'dontdiff' info.
- update URLs for patch scripts
- add Trivial Patch Monkey URL
- add more references for submitting patches
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

New cards included.
V4L1 api renamed. Message included informing it is obsoleted by V4L2 API.
V4L2 api included.
Mark all 7135 cards as 7133.

Signed-off-by: Luc Saillard <luc@saillard.org>.
Signed-off-by: NNickolay V Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: NHermann Pitton <hermann.pitton@onlinehome.de>
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add Philips Webcam format.
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Luc Saillard <luc@saillard.org>.
Signed-off-by: NNickolay V Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

* bttv-driver.c, bttvp.h:

- New bttv module params:

- uv_ratio : allow a ratio of saturation between u and v. If you
        have a ratio of 40 and a saturation of 100, usat will be 80 and
        vstat 120. Useful to correct a bad color balance.
- full_luma_range : provide a better contrast in using the full
        range 0-253 of values instead of 16-253.
- coring : to have a better black level.
- radio range is now defined on tuner-core.c. Cleaning up.

* bttvp.h:

- Fix gcc 4.0 compilation
Signed-off-by: NJorik Jonker <jorik@dnd.utwente.nl>
Signed-off-by: NSylvain Meyer <sylvain.meyer@worldonline.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: NNickolay V Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

*tuner-core.c:
- some tuner_info msgs will be generated only if insmod opt
        tuner_debug enabled.
- Implemented tuner-core support for VIDIO_S_TUNER to allow
        changing mono/stereo mode
- Remove unneeded config options.
- I2C_CLIENT_MULTI option removed.
- support for Philips FMD12ME hybrid tuner
- allow to initialize with another tuner
- Move PHILIPS_FMD initialization code to set_type function,

* tda8290:

- Fix dumb error in tda8290 tunning.
- Radio tuner uses high-precision step instead of 62.5 KHz.

*tea5767.c:
- tuner_info msgs will be generated only if insmod tuner option
        tuner_debug enabled.
- some cleanups for better reading.
- Radio tuner uses high-precision step instead of 62.5 KHz.
- Changing radio mode stereo/mono for tea5767 working.

*tuner-simple.c:
- TNF9533-D/IF UHF fixup.
- Radio tuners now uses high-precision step instead of 62.5 KHz.

*mt20xx.c:
        - Radio tuner uses high-precision step instead of 62.5 KHz.

*tda9887.c:
        - tab and blank spaces corrections.
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: NGerd Knorr <kraxel@bytesex.org>
Signed-off-by: NNickolay V Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch updates maintainer info for BTTV and V4L.
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>
Acked-by: NGerd Knorr <kraxel@bytesex.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Anyone reporting a stuck IRQ should try these options.  Its effectiveness
varies we've found in the Fedora case.  Quite a few systems with misdescribed
IRQ routing just work when you use irqpoll.  It also fixes up the VIA systems
although thats now fixed with the VIA quirk (which we could just make default
as its what Redmond OS does but Linus didn't like it historically).

A small number of systems have jammed IRQ sources or misdescribes that cause
an IRQ that we have no handler registered anywhere for.  In those cases it
doesn't help.
Signed-off-by: NAlan Cox <number6@the-village.bc.nu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>