When a new link instance is created, it is trigged to start by
sending it a TIPC_STARTING_EVT, whereafter a regular link
reset is applied to it.

The starting event is codewise treated as a timeout event, and prompts
a link RESET message to be sent to the peer node, carrying a link
session identifier. The later link_reset() call nudges this session
identifier, whereafter all subsequent RESET messages will be sent out
with the new identifier. The latter session number overrides the former,
causing the peer to unconditionally accept it irrespective of its
current working state.

We don't think that this causes any problem, but it is not in accordance
with the protocol spec, and may cause confusion when debugging TIPC
sessions.

To avoid this, we make the starting event distinct from the
subsequent timeout events, by not allowing the former to send
out any RESET message. This eliminates the described problem.
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instances of struct node are created in the function tipc_disc_rcv()
under the assumption that there is no race between received discovery
messages arriving from the same node. This assumption is wrong.
When we use more than one bearer, it is possible that discovery
messages from the same node arrive at the same moment, resulting in
creation of two instances of struct tipc_node. This may later cause
confusion during link establishment, and may result in one of the links
never becoming activated.

We fix this by making lookup and potential creation of nodes atomic.
Instead of first looking up the node, and in case of failure, create it,
we now start with looking up the node inside node_link_create(), and
return a reference to that one if found. Otherwise, we go ahead and
create the node as we did before.
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During link failover it may happen that the remaining link goes
down while it is still in the process of taking over traffic
from a previously failed link. When this happens, we currently
abort the failover procedure and reset the first failed link to
non-failover mode, so that it will be ready to re-establish
contact with its peer when it comes available.

However, if the first link goes down because its bearer was manually
disabled, it is not enough to reset it; it must also be deleted;
which is supposed to happen when the failover procedure is finished.
Otherwise it will remain a zombie link: attached to the owner node
structure, in mode LINK_STOPPED, and permanently blocking any re-
establishing of the link to the peer via the interface in question.

We fix this by amending the failover abort procedure. Apart from
resetting the link to non-failover state, we test if the link is
also in LINK_STOPPED mode. If so, we delete it, using the conditional
tipc_link_delete() function introduced in the previous commit.
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a bearer is disabled, all pertaining links will be reset and
deleted. However, if there is a second active link towards a killed
link's destination, the delete has to be postponed until the failover
is finished. During this interval, we currently put the link in zombie
mode, i.e., we take it out of traffic, delete its timer, but leave it
attached to the owner node structure until all missing packets have
been received.  When this is done, we detach the link from its node
and delete it, assuming that the synchronous timer deletion that was
initiated earlier in a different thread has finished.

This is unsafe, as the failover may finish before del_timer_sync()
has returned in the other thread.

We fix this by adding an atomic reference counter of type kref in
struct tipc_link. The counter keeps track of the references kept
to the link by the owner node and the timer. We then do a conditional
delete, based on the reference counter, both after the failover has
been finished and when the timer expires, if applicable. Whoever
comes last, will actually delete the link. This approach also implies
that we can make the deletion of the timer asynchronous.
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This one needs to copy the same data from user potentially more than
once.  Sadly, MTU changes can trigger that ;-/

Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

If a large number of namespaces is spawned on a node and TIPC is
enabled in each of these, the excessive printk tracing of network
events will cause the system to grind down to a near halt.
The traces are still of debug value, so instead of removing them
completely we fix it by changing the link state and node availability
logging debug traces.
Signed-off-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 07f6c4bc (tipc: convert tipc reference table to use generic
rhashtable) introduced a problem with port listing in the new netlink
API. It broke the resume functionality resulting in a never ending
loop. This was caused by starting with the first hash table every time
subsequently never returning an empty skb (terminating).

This patch fixes the resume mechanism by keeping a logical reference
to the last hash table along with a logical reference to the socket
(port) that didn't fit in the previous message.
Signed-off-by: NRichard Alpe <richard.alpe@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit f2f9800d "tipc: make tipc node table aware of net
namespace" has added a dereference of sock->sk before making sure it's
not NULL, which makes releasing a tipc socket NULL pointer dereference
for sockets that are not fully initialized.
Signed-off-by: NSasha Levin <sasha.levin@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the redundant timer defined in tipc_sock structure, instead we
can directly reuse the sk_timer defined in sock structure.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Acked-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently tipc module only allows users sitting on "init_net" namespace
to configure it through netlink interface. But now almost each tipc
component is able to be aware of net namespace, so it's time to open
the permission for users residing in other namespaces, allowing them
to configure their own tipc stack instance through netlink interface.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After namespace is supported, each namespace should own its private
random value. So the global variable representing the random value
must be moved to tipc_net structure.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TIPC establishes one subscriber server which allows users to subscribe
their interesting name service status. After tipc supports namespace,
one dedicated tipc stack instance is created for each namespace, and
each instance can be deemed as one independent TIPC node. As a result,
subscriber server must be built for each namespace.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If net namespace is supported in tipc, each namespace will be treated
as a separate tipc node. Therefore, every namespace must own its
private tipc node address. This means the "tipc_own_addr" global
variable of node address must be moved to tipc_net structure to
satisfy the requirement. It's turned out that users also can assign
node address for every namespace.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TIPC name table is used to store the mapping relationship between
TIPC service name and socket port ID. When tipc supports namespace,
it allows users to publish service names only owned by a certain
namespace. Therefore, every namespace must have its private name
table to prevent service names published to one namespace from being
contaminated by other service names in another namespace. Therefore,
The name table global variable (ie, nametbl) and its lock must be
moved to tipc_net structure, and a parameter of namespace must be
added for necessary functions so that they can obtain name table
variable defined in tipc_net structure.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now tipc socket table is statically allocated as a global variable.
Through it, we can look up one socket instance with port ID, insert
a new socket instance to the table, and delete a socket from the
table. But when tipc supports net namespace, each namespace must own
its specific socket table. So the global variable of socket table
must be redefined in tipc_net structure. As a concequence, a new
socket table will be allocated when a new namespace is created, and
a socket table will be deallocated when namespace is destroyed.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TIPC broadcast link is statically established and its relevant states
are maintained with the global variables: "bcbearer", "bclink" and
"bcl". Allowing different namespace to own different broadcast link
instances, these variables must be moved to tipc_net structure and
broadcast link instances would be allocated and initialized when
namespace is created.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bearer list defined as a global variable is used to store bearer
instances. When tipc supports net namespace, bearers created in
one namespace must be isolated with others allocated in other
namespaces, which requires us that the bearer list(bearer_list)
must be moved to tipc_net structure. As a result, a net namespace
pointer has to be passed to functions which access the bearer list.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Global variables associated with node table are below:
- node table list (node_htable)
- node hash table list (tipc_node_list)
- node table lock (node_list_lock)
- node number counter (tipc_num_nodes)
- node link number counter (tipc_num_links)

To make node table support namespace, above global variables must be
moved to tipc_net structure in order to keep secret for different
namespaces. As a consequence, these variables are allocated and
initialized when namespace is created, and deallocated when namespace
is destroyed. After the change, functions associated with these
variables have to utilize a namespace pointer to access them. So
adding namespace pointer as a parameter of these functions is the
major change made in the commit.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Involve namespace infrastructure, make the "tipc_net_id" global
variable aware of per namespace, and rename it to "net_id". In
order that the conversion can be successfully done, an instance
of networking namespace must be passed to relevant functions,
allowing them to access the "net_id" variable of per namespace.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to make tipc socket table aware of namespace, a networking
namespace instance must be passed to tipc_sk_lookup(), allowing it
to look up tipc socket instance with a given port ID from a concrete
socket table. However, as now tipc_sk_timeout() only has one port ID
parameter and is not namespace aware, it's unable to obtain a correct
socket instance through tipc_sk_lookup() just with a port ID,
especially after namespace is completely supported.

If port ID is replaced with socket instance as tipc_sk_timeout()'s
parameter, it's unnecessary to look up socket table. But as the timer
handler - tipc_sk_timeout() is run asynchronously, socket reference
must be held before its timer is launched, and must be carefully
checked to identify whether the socket reference needs to be put or
not when its timer is terminated.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only the works of initializing and shutting down tipc module are done
in core.h and core.c files, so all stuffs which are not closely
associated with the two tasks should be moved to appropriate places.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not only some wrapper function like k_term_timer() is empty, but also
some others including k_start_timer() and k_cancel_timer() don't return
back any value to its caller, what's more, there is no any component
in the kernel world to do such thing. Therefore, these timer interfaces
defined in tipc module should be purged.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove redundant wrapper functions like tipc_core_start() and
tipc_core_stop(), and directly move them to their callers, such
as tipc_init() and tipc_exit(), having us clearly know what are
really done in both initialization and deinitialzation functions.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NTero Aho <Tero.Aho@coriant.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 58dc55f2 ("tipc: use generic
SKB list APIs to manage link transmission queue") we replace all list
traversal loops with the macros skb_queue_walk() or
skb_queue_walk_safe(). While the previous loops were based on the
assumption that the list was NULL-terminated, the standard macros
stop when the iterator reaches the list head, which is non-NULL.

In the function bclink_retransmit_pkt() this macro replacement has
lead to a bug. When we receive a BCAST STATE_MSG we unconditionally
call the function bclink_retransmit_pkt(), whether there really is
anything to retransmit or not, assuming that the sequence number
comparisons will lead to the correct behavior. However, if the
transmission queue is empty, or if there are no eligible buffers in
the transmission queue, we will by mistake pass the list head pointer
to the function tipc_link_retransmit(). Since the list head is not a
valid sk_buff, this leads to a crash.

In this commit we fix this by only calling tipc_link_retransmit()
if we actually found eligible buffers in the transmission queue.
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 58dc55f2 ("tipc: use generic
SKB list APIs to manage link transmission queue") we replace all list
traversal loops with the macros skb_queue_walk() or
skb_queue_walk_safe(). While the previous loops were based on the
assumption that the list was NULL-terminated, the standard macros
stop when the iterator reaches the list head, which is non-NULL.

In the function bclink_retransmit_pkt() this macro replacement has
lead to a bug. When we receive a BCAST STATE_MSG we unconditionally
call the function bclink_retransmit_pkt(), whether there really is
anything to retransmit or not, assuming that the sequence number
comparisons will lead to the correct behavior. However, if the
transmission queue is empty, or if there are no eligible buffers in
the transmission queue, we will by mistake pass the list head pointer
to the function tipc_link_retransmit(). Since the list head is not a
valid sk_buff, this leads to a crash.

In this commit we fix this by only calling tipc_link_retransmit()
if we actually found eligible buffers in the transmission queue.
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As tipc reference table is statically allocated, its memory size
requested on stack initialization stage is quite big even if the
maximum port number is just restricted to 8191 currently, however,
the number already becomes insufficient in practice. But if the
maximum ports is allowed to its theory value - 2^32, its consumed
memory size will reach a ridiculously unacceptable value. Apart from
this, heavy tipc users spend a considerable amount of time in
tipc_sk_get() due to the read-lock on ref_table_lock.

If tipc reference table is converted with generic rhashtable, above
mentioned both disadvantages would be resolved respectively: making
use of the new resizable hash table can avoid locking on the lookup;
smaller memory size is required at initial stage, for example, 256
hash bucket slots are requested at the beginning phase instead of
allocating the entire 8191 slots in old mode. The hash table will
grow if entries exceeds 75% of table size up to a total table size
of 1M, and it will automatically shrink if usage falls below 30%,
but the minimum table size is allowed down to 256.

Also converts ref_table_lock to a separate mutex to protect hash table
mutations on write side. Lastly defers the release of the socket
reference using call_rcu() to allow using an RCU read-side protected
call to rhashtable_lookup().
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Acked-by: NJon Maloy <jon.maloy@ericsson.com>
Acked-by: NErik Hugne <erik.hugne@ericsson.com>
Cc: Thomas Graf <tgraf@suug.ch>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix sparse warning:
net/tipc/link.c:1924:40: warning: Using plain integer as NULL pointer
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 908344cd ("tipc: fix bug in multicast congestion handling")
introduced a race in the broadcast link wakeup functionality.

This patch eliminates this broadcast link wakeup race caused by
operation on the wakeup list without proper locking. If this race
hit and corrupted the list all subsequent wakeup messages would be
lost, resulting in a considerable memory leak.
Signed-off-by: NRichard Alpe <richard.alpe@ericsson.com>
Signed-off-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit fb9962f3 ("tipc: ensure all name sequences are properly
protected with its lock") involves below errors:

net/tipc/name_table.c:980 tipc_purge_publications() error: double lock 'spin_lock:&seq->lock'
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Note that the code _using_ ->msg_iter at that point will be very
unhappy with anything other than unshifted iovec-backed iov_iter.
We still need to convert users to proper primitives.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

commit 908344cd ("tipc: fix bug in multicast congestion
handling") introduced two bugs with the bclink wakeup
function. This commit fixes the missing spinlock init for the
waiting_sks list. We also eliminate the race condition
between the waiting_sks length check/dequeue operations in
tipc_bclink_wakeup_users by simply removing the redundant
length check.
Signed-off-by: NErik Hugne <erik.hugne@ericsson.com>
Acked-by: NTero Aho <Tero.Aho@coriant.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Part of the old remote management feature is a piece of code
that checked permissions on the local system to see if a certain
operation was permitted, and if so pass the command to a remote
node. This serves no purpose after the removal of remote management
with commit 5902385a ("tipc: obsolete the remote management
feature") so we remove it.
Signed-off-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert tipc name table read-write lock to RCU. After this change,
a new spin lock is used to protect name table on write side while
RCU is applied on read side.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a list_head variable is seen as a new entry to be added to a
list head, it's unnecessary to be initialized with INIT_LIST_HEAD().
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When tipc name sequence is published, name table lock is released
before name sequence buffer is delivered to remote nodes through its
underlying unicast links. However, when name sequence is withdrawn,
the name table lock is held until the transmission of the removal
message of name sequence is finished. During the process, node lock
is nested in name table lock. To prevent node lock from being nested
in name table lock, while withdrawing name, we should adopt the same
locking policy of publishing name sequence: name table lock should
be released before message is sent.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As tipc_nametbl_lock is used to protect name_table structure, the lock
must be held while all members of name_table structure are accessed.
However, the lock is not obtained while a member of name_table
structure - local_publ_count is read in tipc_nametbl_publish(), as
a consequence, an inconsistent value of local_publ_count might be got.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TIPC internally created a name table which is used to store name
sequences. Now there is a read-write lock - tipc_nametbl_lock to
protect the table, and each name sequence saved in the table is
protected with its private lock. When a name sequence is inserted
or removed to or from the table, its members might need to change.
Therefore, in normal case, the two locks must be held while TIPC
operates the table. However, there are still several places where
we only hold tipc_nametbl_lock without proprerly obtaining name
sequence lock, which might cause the corruption of name sequence.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As TIPC subscriber server is terminated before name table, no user
depends on subscription list of name sequence when name table is
stopped. Therefore, all name sequences stored in name table should
be released whatever their subscriptions lists are empty or not,
otherwise, memory leak might happen.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Name table locking policy is going to be adjusted from read-write
lock protection to RCU lock protection in the future commits. But
its essential precondition is to convert the allocation way of name
table from static to dynamic mode.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>