A kernel oops/panic prints an instruction dump showing several
instructions before and after the instruction which caused the
oops/panic.

The code intended that the faulting instruction be enclosed in angle
brackets, however a bug caused the faulting instruction to be
interpreted by printk() as the message log level.

To fix this, the KERN_CONT log level is added before the actual text of
the printed message.

=== Before the patch ===

[ 1081.587266] Instruction dump:
[ 1081.590236] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
[ 1081.598034] 3d20c03a 9009a114 7c0004ac 39200000
[ 1081.602500]  4e800020 3803ffd0 2b800009

<4>[ 1081.587266] Instruction dump:
<4>[ 1081.590236] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
<4>[ 1081.598034] 3d20c03a 9009a114 7c0004ac 39200000
<98090000>[ 1081.602500]  4e800020 3803ffd0 2b800009

=== After the patch ===

[   51.385216] Instruction dump:
[   51.388186] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
[   51.395986] 3d20c03a 9009a114 7c0004ac 39200000 <98090000> 4e800020 3803ffd0 2b800009

<4>[   51.385216] Instruction dump:
<4>[   51.388186] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
<4>[   51.395986] 3d20c03a 9009a114 7c0004ac 39200000 <98090000> 4e800020 3803ffd0 2b800009
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

EEH may happen during a PCI driver probe. If the driver is trying to
access some register in a loop, the EEH code will try to print the
driver name. But the driver pointer in struct pci_dev is not set until
probe returns successfully.

Use a function to test if the device and the driver pointer is NULL
before accessing the driver's name.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This fixes a hang that was observed during live partition migration.
Since stop_topology_update must not be called from an interrupt
context, call it earlier in the migration process. The hang observed
can be seen below:

WARNING: at kernel/timer.c:1011
Modules linked in: ip6t_LOG xt_tcpudp xt_pkttype ipt_LOG xt_limit ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_raw xt_NOTRACK ipt_REJECT xt_state iptable_raw iptable_filter ip6table_mangle nf_conntrack_netbios_ns nf_conntrack_broadcast nf_conntrack_ipv4 nf_conntrack nf_defrag_ipv4 ip_tables ip6table_filter ip6_tables x_tables ipv6 fuse loop ibmveth sg ext3 jbd mbcache raid456 async_raid6_recov async_pq raid6_pq async_xor xor async_memcpy async_tx raid10 raid1 raid0 scsi_dh_alua scsi_dh_rdac scsi_dh_hp_sw scsi_dh_emc dm_round_robin dm_multipath scsi_dh sd_mod crc_t10dif ibmvfc scsi_transport_fc scsi_tgt scsi_mod dm_snapshot dm_mod
NIP: c0000000000c52d8 LR: c00000000004be28 CTR: 0000000000000000
REGS: c00000005ffd77d0 TRAP: 0700   Not tainted  (3.2.0-git-00001-g07d106d0)
MSR: 8000000000021032 <ME,CE,IR,DR>  CR: 48000084  XER: 00000001
CFAR: c00000000004be20
TASK = c00000005ec78860[0] 'swapper/3' THREAD: c00000005ec98000 CPU: 3
GPR00: 0000000000000001 c00000005ffd7a50 c000000000fbbc98 c000000000ec8340
GPR04: 00000000282a0020 0000000000000000 0000000000004000 0000000000000101
GPR08: 0000000000000012 c00000005ffd4000 0000000000000020 c000000000f3ba88
GPR12: 0000000000000000 c000000007f40900 0000000000000001 0000000000000004
GPR16: 0000000000000001 0000000000000000 0000000000000000 c000000001022310
GPR20: 0000000000000001 0000000000000000 0000000000200200 c000000001029e14
GPR24: 0000000000000000 0000000000000001 0000000000000040 c00000003f74bc80
GPR28: c00000003f74bc84 c000000000f38038 c000000000f16b58 c000000000ec8340
NIP [c0000000000c52d8] .del_timer_sync+0x28/0x60
LR [c00000000004be28] .stop_topology_update+0x20/0x38
Call Trace:
[c00000005ffd7a50] [c00000005ec78860] 0xc00000005ec78860 (unreliable)
[c00000005ffd7ad0] [c00000000004be28] .stop_topology_update+0x20/0x38
[c00000005ffd7b40] [c000000000028378] .__rtas_suspend_last_cpu+0x58/0x260
[c00000005ffd7bf0] [c0000000000fa230] .generic_smp_call_function_interrupt+0x160/0x358
[c00000005ffd7cf0] [c000000000036ec8] .smp_ipi_demux+0x88/0x100
[c00000005ffd7d80] [c00000000005c154] .icp_hv_ipi_action+0x5c/0x80
[c00000005ffd7e00] [c00000000012a088] .handle_irq_event_percpu+0x100/0x318
[c00000005ffd7f00] [c00000000012e774] .handle_percpu_irq+0x84/0xd0
[c00000005ffd7f90] [c000000000022ba8] .call_handle_irq+0x1c/0x2c
[c00000005ec9ba20] [c00000000001157c] .do_IRQ+0x22c/0x2a8
[c00000005ec9bae0] [c0000000000054bc] hardware_interrupt_entry+0x18/0x1c
Exception: 501 at .cpu_idle+0x194/0x2f8
    LR = .cpu_idle+0x194/0x2f8
[c00000005ec9bdd0] [c000000000017e58] .cpu_idle+0x188/0x2f8 (unreliable)
[c00000005ec9be90] [c00000000067ec18] .start_secondary+0x3e4/0x524
[c00000005ec9bf90] [c0000000000093e8] .start_secondary_prolog+0x10/0x14
Instruction dump:
ebe1fff8 4e800020 fbe1fff8 7c0802a6 f8010010 7c7f1b78 f821ff81 78290464
80090014 5400019e 7c0000d0 78000fe0 <0b000000> 4800000c 7c210b78 7c421378
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We need to disable interrupts when taking the phb->lock. Otherwise
we could deadlock with pci_lock taken from an interrupt.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We use __get_cpu_var() which triggers a false positive warning
in smp_processor_id() thinking interrupts are enabled (at this
point, they are soft-enabled but hard-disabled).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We call the cache_hwirq_map() function with a linux IRQ number
but it expects a HW irq number. This triggers a BUG on multic-chip
setups in addition to not doing the right thing.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

With this change, helpers such as instruction_pointer() et al, get defined
in the generic header in terms of GET_IP

Removed the unnecessary definition of profile_pc in !CONFIG_SMP case as
suggested by Mike Frysinger.
Signed-off-by: NSrikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

It appears that on the Chroma card, the class code of the root
complex is still wrong even on DD2 or later chips. This could
be a firmware issue, but that breaks resource allocation so let's
unconditionally fix it up.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Prevent OMAP UARTs from going idle while they are still transferring
data in PIO mode.  This works around an oversight in the OMAP UART
hardware present in OMAP34xx and earlier: an idle UART won't send a
wakeup when the TX FIFO threshold is reached.  This causes long delays
during data transmission when the MPU powerdomain enters a low-power
mode.  The MPU interrupt controller is not able to respond to
interrupts when it's in a low-power state, so the TX buffer is not
refilled until another wakeup event occurs.

This fix changes the erratum i291 DMA idle workaround.  Rather than
toggling between force-idle and no-idle, it will toggle between
smart-idle and no-idle.  The important part of the workaround is the
no-idle part, so this shouldn't result in any change in behavior.

This fix should work on all OMAP UARTs.  Future patches intended for
the 3.4 merge window will make this workaround conditional on a
"feature" flag, and will use the OMAP36xx+ TX event wakeup support.

Thanks to Kevin Hilman <khilman@ti.com> for mentioning the erratum i291
workaround, which led to the development of this approach.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NGovindraj.R <govindraj.raja@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The following patch fixes a bug introduced by the following
commit:

        e050e3f0 ("perf: Fix broken interrupt rate throttling")

The patch caused the following warning to pop up depending on
the sampling frequency adjustments:

  ------------[ cut here ]------------
  WARNING: at arch/x86/kernel/cpu/perf_event.c:995 x86_pmu_start+0x79/0xd4()

It was caused by the following call sequence:

perf_adjust_freq_unthr_context.part() {
     stop()
     if (delta > 0) {
          perf_adjust_period() {
              if (period > 8*...) {
                  stop()
                  ...
                  start()
              }
          }
      }
      start()
}

Which caused a double start and a double stop, thus triggering
the assert in x86_pmu_start().

The patch fixes the problem by avoiding the double calls. We
pass a new argument to perf_adjust_period() to indicate whether
or not the event is already stopped. We can't just remove the
start/stop from that function because it's called from
__perf_event_overflow where the event needs to be reloaded via a
stop/start back-toback call.

The patch reintroduces the assertion in x86_pmu_start() which
was removed by commit:

	84f2b9b2 ("perf: Remove deprecated WARN_ON_ONCE()")

In this second version, we've added calls to disable/enable PMU
during unthrottling or frequency adjustment based on bug report
of spurious NMI interrupts from Eric Dumazet.
Reported-and-tested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NStephane Eranian <eranian@google.com>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: markus@trippelsdorf.de
Cc: paulus@samba.org
Link: http://lkml.kernel.org/r/20120207133956.GA4932@quad
[ Minor edits to the changelog and to the code ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Upstream commit d1fce9c1

   "ARM: restart: bcmring: use new restart hook"

breaks building of this platform, since what used to be the
last field of the MACHINE_START/END block didn't have a
trailing comma.  Once another field was added below, we get:

arch/arm/mach-bcmring/arch.c:198: error: request for member 'restart' in something not a structure or union
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NJiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Remove BCMRING DMA map code which is no longer used.

This also fixes a build error with dma.c introduced by
bfcd2ea6.
Signed-off-by: NJiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Enable use of the generic atomic64 implementation on AVR32 platforms.
Without this the kernel fails to build as the architecture does not
provide its version.
Signed-off-by: NFabio Baltieri <fabio.baltieri@gmail.com>
Acked-by: NHans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Defining memscan() as memchr() is wrong, because the return values of
memscan() and memchr() are different when the character is not found.  So
use the generic memscan() implementation to fix this.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__kuser_cmpxchg64 has a return path using bx lr to get back to the caller.
This is actually ok since the code in question is predicated on
CONFIG_CPU_32v6K, but for the sake of consistency using the usr_ret
macro is probably better.
Acked-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

With the new throttling/unthrottling code introduced with
commit:

  e050e3f0 ("perf: Fix broken interrupt rate throttling")

we occasionally hit two WARN_ON_ONCE() checks in:

  - intel_pmu_pebs_enable()
  - intel_pmu_lbr_enable()
  - x86_pmu_start()

The assertions are no longer problematic. There is a valid
path where they can trigger but it is harmless.

The assertion can be triggered with:

  $ perf record -e instructions:pp ....

Leading to paths:

  intel_pmu_pebs_enable
  intel_pmu_enable_event
  x86_perf_event_set_period
  x86_pmu_start
  perf_adjust_freq_unthr_context
  perf_event_task_tick
  scheduler_tick

And:

  intel_pmu_lbr_enable
  intel_pmu_enable_event
  x86_perf_event_set_period
  x86_pmu_start
  perf_adjust_freq_unthr_context.
  perf_event_task_tick
  scheduler_tick

cpuc->enabled is always on because when we get to
perf_adjust_freq_unthr_context() the PMU is not totally
disabled. Furthermore when we need to adjust a period,
we only stop the event we need to change and not the
entire PMU. Thus, when we re-enable, cpuc->enabled is
already set. Note that when we stop the event, both
pebs and lbr are stopped if necessary (and possible).
Signed-off-by: NStephane Eranian <eranian@google.com>
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/20120202110401.GA30911@quadSigned-off-by: NIngo Molnar <mingo@elte.hu>

Linux uses two PMD entries for a PTE with the classic page table format,
covering 2MB range. However, the __pte_free_tlb() function only adds a
single TLB flush corresponding to 1MB range covering 'addr'. On
Cortex-A15, level 1 entries can be cached by the TLB independently of
the level 2 entries and without additional flushing a PMD entry would be
left pointing at the wrong PTE. The patch limits the TLB flushing range
to two 4KB pages around the 1MB boundary within PMD.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 89d6c0b5 ("perf, arch: Add generic NODE cache events") added
empty NODE event definitions for the ARM PMU implementations. This was
merged along with Cortex-A5 and Cortex-A15 PMU support, so they missed
out on the original patch.

This patch adds the empty definitions to Cortex-A5 and Cortex-A15.
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If we are context switched whilst copying into a thread's
vfp_hard_struct then the partial copy may be corrupted by the VFP
context switching code (see "ARM: vfp: flush thread hwstate before
restoring context from sigframe").

This patch updates the ptrace VFP set code so that the thread state is
flushed before the copy, therefore disabling VFP and preventing
corruption from occurring.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

In a preemptible kernel, vfp_set() can be preempted, causing the
hardware VFP context to be switched while the thread vfp state is
being read and modified.  This leads to a race condition which can
cause the thread vfp state to become corrupted if lazy VFP context
save occurs due to preemption in between the time thread->vfpstate
is read and the time the modified state is written back.

This may occur if preemption occurs during the execution of a
ptrace() call which modifies the VFP register state of a thread.
Such instances should be very rare in most realistic scenarios --
none has been reported, so far as I am aware.  Only uniprocessor
systems should be affected, since VFP context save is not currently
lazy in SMP kernels.

The problem was introduced by my earlier patch migrating to use
regsets to implement ptrace.

This patch does a vfp_sync_hwstate() before reading
thread->vfpstate, to make sure that the thread's VFP state is not
live in the hardware registers while the registers are modified.

Thanks to Will Deacon for spotting this.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Following execution of a signal handler, we currently restore the VFP
context from the ucontext in the signal frame. This involves copying
from the user stack into the current thread's vfp_hard_struct and then
flushing the new data out to the hardware registers.

This is problematic when using a preemptible kernel because we could be
context switched whilst updating the vfp_hard_struct. If the current
thread has made use of VFP since the last context switch, the VFP
notifier will copy from the hardware registers into the vfp_hard_struct,
overwriting any data that had been partially copied by the signal code.

Disabling preemption across copy_from_user calls is a terrible idea, so
instead we move the VFP thread flush *before* we update the
vfp_hard_struct. Since the flushing is performed lazily, this has the
effect of disabling VFP and clearing the CPU's VFP state pointer,
therefore preventing the thread from being updated with stale data on
the next context switch.

Cc: stable <stable@vger.kernel.org>
Tested-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This reverts commit 3c424f35.

Joachim Eastwood reports:
| "ARM: 7304/1: ioremap: fix boundary check when reusing static mapping"
| Commit: 3c424f35 in Linus master
|
| Breaks booting on my custom AT91RM9200 board.
| There isn't any error messages or anything that indicates what goes
| wrong it just stops after; Uncompressing Linux... done, booting the
| kernel.
|
| Reverting it makes my board boot again.

and further debugging reveals:

ioremap: pfn=fffff phys=fffff000 offset=400 size=1000
ioremap: area c3ffdfc0: phys_addr=200000 pfn=200 size=4000
ioremap: found: addr fef74000 => fed73000 => fed73400

Clearly, an area for pfn 0x200, 16K can't ever satisfy a request for pfn
0xfffff.  This happens because the changed if statement becomes:

                if (0x00200 > 0xfffff ||
                    0xfffff000 + 0x400 + 0x1000-1 > 0x00200000 + 0x4000-1)
and therefore:
                if (0x00200 > 0xfffff ||
                    0x000003ff > 0x00203fff)

The if condition fails, and so we _believe_ that the SRAM mapping fits
our request.  Clearly that's totally bogus.

Moreover, the original premise of the 'fix' patch was wrong:
|    The condition checking boundaries of the requested and existing
|    mappings didn't take in-page offset into consideration though,
|    which lead to obscure and hard to debug problems when requested
|    mapping crossed end of the static one.

as the code immediately above this loop does:

        size = PAGE_ALIGN(offset + size);

so 'size' already contains the requested offset into the page.

So, revert the broken 'fix'.
Acked-by: NNicolas Pitre <nico@linaro.org>

Both sparc 32-bit's software divide assembler and MPILIB provide
clz_tab[] with identical contents.

Break it out into a seperate object file and select it when
SPARC32 or MPILIB is set.
Reported-by: NAl Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NJames Morris <jmorris@namei.org>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Return to behaviour perf MSR had before introducing vPMU in case vPMU
is disabled. Some guests access those registers unconditionally and do
not expect it to fail.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

On hosts without this patch, 32bit guests will crash (and 64bit guests
may behave in a wrong way) for example by simply executing following
nasm-demo-application:

    [bits 32]
    global _start
    SECTION .text
    _start: syscall

(I tested it with winxp and linux - both always crashed)

    Disassembly of section .text:

    00000000 <_start>:
       0:   0f 05                   syscall

The reason seems a missing "invalid opcode"-trap (int6) for the
syscall opcode "0f05", which is not available on Intel CPUs
within non-longmodes, as also on some AMD CPUs within legacy-mode.
(depending on CPU vendor, MSR_EFER and cpuid)

Because previous mentioned OSs may not engage corresponding
syscall target-registers (STAR, LSTAR, CSTAR), they remain
NULL and (non trapping) syscalls are leading to multiple
faults and finally crashs.

Depending on the architecture (AMD or Intel) pretended by
guests, various checks according to vendor's documentation
are implemented to overcome the current issue and behave
like the CPUs physical counterparts.

[mtosatti: cleanup/beautify code]
Signed-off-by: NStephan Baerwolf <stephan.baerwolf@tu-ilmenau.de>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

In order to be able to proceed checks on CPU-specific properties
within the emulator, function "get_cpuid" is introduced.
With "get_cpuid" it is possible to virtually call the guests
"cpuid"-opcode without changing the VM's context.

[mtosatti: cleanup/beautify code]
Signed-off-by: NStephan Baerwolf <stephan.baerwolf@tu-ilmenau.de>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

commit 43db595e
(sh: switch to GENERIC_PCI_IOMAP)
failed to take into account the PCI channels's
io_map_base for mapping IO BARs.
This also caused a new warning on sh.

Fix this, without re-introducing code duplication,
by setting NO_GENERIC_PCI_IOPORT_MAP
and supplying a sh-specific __pci_ioport_map.
Reported-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

commit eab90291
(mips: switch to GENERIC_PCI_IOMAP)
failed to take into account the PCI controller's
io_map_base for mapping IO BARs.
This also caused a new warning on mips.

Fix this, without re-introducing code duplication,
by setting NO_GENERIC_PCI_IOPORT_MAP
and supplying a mips-specific __pci_ioport_map.
Reported-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

This reverts commit d761f0c5.

Patch: "cpu: Register a generic CPU device on architectures that currently do not"
(sha1: 9f13a1fd)

selects GENERIC_CPU_DEVICES for Microblaze which register cpu.
My patch was done in the same time that's why cpu was registered twice which
caused this warning log:

------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:481 sysfs_add_one+0xb0/0xdc()
sysfs: cannot create duplicate filename '/devices/system/cpu/cpu0'
Modules linked in:
...
Signed-off-by: NMichal Simek <monstr@monstr.eu>

This commit removes the reboot quirk originally added by commit
e19e074b ("x86: Fix reboot problem on VersaLogic Menlow boards").

Testing with a VersaLogic Ocelot (VL-EPMs-21a rev 1.00 w/ BIOS
6.5.102) revealed the following regarding the reboot hang
problem:

- v2.6.37 reboot=bios was needed.

- v2.6.38-rc1: behavior changed, reboot=acpi is needed,
  reboot=kbd and reboot=bios results in system hang.

- v2.6.38: VersaLogic patch (e19e074b "x86: Fix reboot problem on
  VersaLogic Menlow boards") was applied prior to v2.6.38-rc7.  This
  patch sets a quirk for VersaLogic Menlow boards that forces the use
  of reboot=bios, which doesn't work anymore.

- v3.2: It seems that commit 660e34ce ("x86: Reorder reboot method
  preferences") changed the default reboot method to acpi prior to
  v3.0-rc1, which means the default behavior is appropriate for the
  Ocelot.  No VersaLogic quirk is required.

The Ocelot board used for testing can successfully reboot w/out
having to pass any reboot= arguments for all 3 current versions
of the BIOS.
Signed-off-by: NMichael D Labriola <michael.d.labriola@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Michael D Labriola <mlabriol@gdeb.com>
Cc: Kushal Koolwal <kushalkoolwal@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/87vcnub9hu.fsf@gmail.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Skip DMI checks for vendor specific reboot quirks if the user
passed in a reboot= arg on the command line - we should never
override user choices.
Signed-off-by: NMichael D Labriola <michael.d.labriola@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Michael D Labriola <mlabriol@gdeb.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/87wr8ab9od.fsf@gmail.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Smatch complains that we have some inconsistent NULL checking.

If "task" were NULL then it would lead to a NULL dereference
later. We can remove this test because earlier on in the
function we have:

 if (!task)
	task = current;
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Clemens Ladisch <clemens@ladisch.de>
Link: http://lkml.kernel.org/r/20120128105246.GA25092@elgon.mountainSigned-off-by: NIngo Molnar <mingo@elte.hu>

Since commit 576d2f25 "ARM: add
generic ioremap optimization by reusing static mappings" ioremap()
is trying to reuse existing static mapping when possible.

The condition checking boundaries of the requested and existing
mappings didn't take in-page offset into consideration though,
which lead to obscure and hard to debug problems when requested
mapping crossed end of the static one.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 5a05a820 ("davinci_emac:
use an unique MDIO bus name") introduced during the v3.3 merge
window updated the davinci mdio bus name to make it unique.

Update the bus name in board files which use DaVinci MDIO bus
to match the new name. Without this PHY is not detected with
error like:

PHY 0:01 not found
net eth0: could not connect to phy 0:01

Tested on DM365 and DA850 EVMs.

Cc: Florian Fainelli <florian@openwrt.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
    when != iounmap(e)
*if (...)
   { ... when != iounmap(e)
     return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NTony Lindgren <tony@atomide.com>

pdata needs to be freed before leaving the function in an error case.

A simplified version of the semantic match that finds the problem is as
follows: (http://coccinelle.lip6.fr)

// <smpl>
@r exists@
local idexpression x;
statement S;
identifier f1;
position p1,p2;
expression *ptr != NULL;
@@

x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...x...+> }
x->f1
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Currently MMC2 setup code can only enable loopback clock and
relies on reset value for boards that need to have it disabled.
This causes a problem with certain bootloaders that always enable
that clock, resulting with unwanted bootloader dependencies.

Fix this by making it disable the clock if board data says so.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

hsmmc23_before_set_reg() can set MMCSDIO2ADPCLKISEL bit, which
enables internal clock for MMC2. Currently this function is also called
by code handling MMC3, and if .internal_clock is set in platform data
(by default it currently is), it will set MMCSDIO2ADPCLKISEL for MMC2
instead of MMC3 (MMC3 doesn't have such bit so nothing actually needs to
be done). This breaks 2nd SD slot on pandora.

Fix this by changing hsmmc23_before_set_reg() to only handle MMC2.
Note that this removes .remux() call for MMC3, but no board currently
needs it and it's also not called for MMC4 and MMC5.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

following statement can only change device size from 8-bit(0) to 16-bit(1),
but not vice versa:

regval |= GPMC_CONFIG1_DEVICESIZE(wval);

so as this field has 1 reserved bit, that could be used in future,
just clear both bits and then OR with the desired value
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NTony Lindgren <tony@atomide.com>