- 30 11月, 2009 7 次提交
-
-
由 Dan Carpenter 提交于
The other paths all drop chan->wsem. This was found by a static checker (smatch). Signed-off-by: NDan Carpenter <error27@gmail.com> Acked-by: NJan "Yenya" Kasprzak <kas@fi.muni.cz> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
If we happen to have registered the driver without passing a MAC address, we will print a zero MAC address and register the interface with this invalid address, this is confusin. This patch moves the checking of a valid ethernet address and the generation of a random one down from the open function to the probe function. Signed-off-by: NFlorian Fainelli <florian@openwrt.org> Acked-by: NLennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Russell King - ARM Linux 提交于
smc91x.h defines SMC_IRQ_FLAGS to be -1 when it wants the interrupt flags to be taken from the resource structure. However, d280eadc changed this to checking for non-zero resource flags. Unfortunately, this means that on some platforms, we end up passing '-1' to request_irq rather than the desired result. Combine the two conditions into one so that the IRQ flags are taken from the resource if either SMC_IRQ_FLAGS is -1 or the resource flags specify an interrupt trigger. This restores network on at least the Versatile platform. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk> Acked-by: NEric Miao <eric.y.miao@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Steve Glendinning 提交于
This patch fixes a null pointer dereference BUG() if ethtool is used on an smsc9420 interface while it is down, because the phy_dev is only allocated while the interface is up. Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ivan Vecera 提交于
The newer chipsets (all PCI-E) are known that they need full power cycle (AC or battery removal) to reset MAC address to a hardwired one. Previous patch to address this problem loads the original MAC address from EEPROM. But it brought other problem for which it is necessary to introduce a new module parameter. However, it might suffice to restore the initial MAC address before shutdown/reboot/kexec and when removing the module. Signed-off-by: NIvan Vecera <ivecera@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Ford 提交于
ipv4 ip_frag_reasm(), fully replace 'dev_net(dev)' with 'net', defined previously patched into 2.6.29. Between 2.6.28.10 and 2.6.29, net/ipv4/ip_fragment.c was patched, changing from dev_net(dev) to container_of(...). Unfortunately the goto section (out_fail) on oversized packets inside ip_frag_reasm() didn't get touched up as well. Oversized IP packets cause a NULL pointer dereference and immediate hang. I discovered this running openvasd and my previous email on this is titled: NULL pointer dereference at 2.6.32-rc8:net/ipv4/ip_fragment.c:566 Signed-off-by: NDavid Ford <david@blue-labs.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Roger Oksanen 提交于
pci_alloc_consistent uses GFP_ATOMIC allocation that may fail on some systems with limited memory (Bug #14265). pci_pool_alloc allows waiting with GFP_KERNEL. Tested-by: NKarol Lewandowski <karol.k.lewandowski@gmail.com> Signed-off-by: NRoger Oksanen <roger.oksanen@cs.helsinki.fi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 11月, 2009 1 次提交
-
-
由 Andrei Pelinescu-Onciul 提交于
When retransmitting due to T3 timeout, retransmit all the in-flight chunks for the corresponding transport/path, including chunks sent less then 1 rto ago. This is the correct behaviour according to rfc4960 section 6.3.3 E3 and "Note: Any DATA chunks that were sent to the address for which the T3-rtx timer expired but did not fit in one MTU (rule E3 above) should be marked for retransmission and sent as soon as cwnd allows (normally, when a SACK arrives). ". This fixes problems when more then one path is present and the T3 retransmission of the first chunk that timeouts stops the T3 timer for the initial active path, leaving all the other in-flight chunks waiting forever or until a new chunk is transmitted on the same path and timeouts (and this will happen only if the cwnd allows sending new chunks, but since cwnd was dropped to MTU by the timeout => it will wait until the first heartbeat). Example: 10 packets in flight, sent at 0.1 s intervals on the primary path. The primary path is down and the first packet timeouts. The first packet is retransmitted on another path, the T3 timer for the primary path is stopped and cwnd is set to MTU. All the other 9 in-flight packets will not be retransmitted (unless more new packets are sent on the primary path which depend on cwnd allowing it, and even in this case the 9 packets will be retransmitted only after a new packet timeouts which even in the best case would be more then RTO). This commit reverts d0ce9291 and also removes the now unused transport->last_rto, introduced in b6157d8e. p.s The problem is not only when multiple paths are there. It can happen in a single homed environment. If the application stops sending data, it possible to have a hung association. Signed-off-by: NAndrei Pelinescu-Onciul <andrei@iptel.org> Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 11月, 2009 1 次提交
-
-
由 Eric Dumazet 提交于
When multi queue compatable names are used by pktgen (eg eth0@0), we currently cannot unload a NIC driver if one of its device is currently in use. Allow pktgen_find_dev() to find pktgen devices by their suffix (netdev name) Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 11月, 2009 10 次提交
-
-
由 Patrick McHardy 提交于
gso_max_size must be set based on the value of the underlying device to support devices not using the full 64k. Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Johannes Berg 提交于
The /dev/rfkill ops don't refer to the module, so it is possible to unload the module while file descriptors are open. Fix this oversight. Reported-by: NMaxim Levitsky <maximlevitsky@gmail.com> Cc: stable@kernel.org Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
Copied from original one-line patch here: http://bugzilla.kernel.org/show_bug.cgi?id=14267#c26Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Antti Kaijanmäki 提交于
Fix soft-lockup in hso.c which is triggered on SMP machine when modem is removed while file descriptor(s) under /dev are still open: old version called kref_put() too early which resulted in destroying hso_serial and hso_device objects which were still used later on. Signed-off-by: NAntti Kaijanmäki <antti.kaijanmaki@nomovok.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Antti Kaijanmäki 提交于
Signed-off-by: NAntti Kaijanmäki <antti.kaijanmaki@nomovok.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Commit e6fce5b9 (pktgen: multiqueue etc.) tried to relax the pktgen restriction of one device per kernel thread, adding a '@' tag to device names. Problem is we dont perform check on full pktgen device name. This allows adding many time same 'device' to pktgen thread pgset "add_device eth0@0" one session later : pgset "add_device eth0@0" (This doesnt find previous device) This consumes ~1.5 MBytes of vmalloc memory per round and also triggers this warning : [ 673.186380] proc_dir_entry 'pktgen/eth0@0' already registered [ 673.186383] Modules linked in: pktgen ixgbe ehci_hcd psmouse mdio mousedev evdev [last unloaded: pktgen] [ 673.186406] Pid: 6219, comm: bash Tainted: G W 2.6.32-rc7-03302-g41cec6f1-dirty #16 [ 673.186410] Call Trace: [ 673.186417] [<ffffffff8104a29b>] warn_slowpath_common+0x7b/0xc0 [ 673.186422] [<ffffffff8104a341>] warn_slowpath_fmt+0x41/0x50 [ 673.186426] [<ffffffff8114e789>] proc_register+0x109/0x210 [ 673.186433] [<ffffffff8100bf2e>] ? apic_timer_interrupt+0xe/0x20 [ 673.186438] [<ffffffff8114e905>] proc_create_data+0x75/0xd0 [ 673.186444] [<ffffffffa006ad38>] pktgen_thread_write+0x568/0x640 [pktgen] [ 673.186449] [<ffffffffa006a7d0>] ? pktgen_thread_write+0x0/0x640 [pktgen] [ 673.186453] [<ffffffff81149144>] proc_reg_write+0x84/0xc0 [ 673.186458] [<ffffffff810f5a58>] vfs_write+0xb8/0x180 [ 673.186463] [<ffffffff810f5c11>] sys_write+0x51/0x90 [ 673.186468] [<ffffffff8100b51b>] system_call_fastpath+0x16/0x1b [ 673.186470] ---[ end trace ccbb991b0a8d994d ]--- Solution to this problem is to use a odevname field (includes @ tag and suffix), instead of using netdevice name. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NRobert Olsson <robert.olsson@its.uu.se> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Giuseppe CAVALLARO 提交于
If the external timer cannot be used the driver will continue to work without mitigation. Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Giuseppe CAVALLARO 提交于
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 11月, 2009 2 次提交
-
-
由 Patrick McHardy 提交于
Commit acc738fe (netfilter: xtables: avoid pointer to self) introduced an invalid return value in limit_mt_check(). Signed-off-by: NPatrick McHardy <kaber@trash.net>
-
由 Alexander Beregalov 提交于
Andreas Lohre reported that the driver crashes when trying to register_netdev(), he sugessted to move dev->netdev_ops initialization before calling register_netdev(), it worked for him. Reported-by: NAndreas Lohre <alohre@gmail.com> Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 22 11月, 2009 3 次提交
-
-
由 Narender Kumar 提交于
o Along with netdev->perm_addr, mac address will be maintained in device private structure. o Device limitation: We need to set mac address when ever interface comes up. In ALB/TAL mode, bonding driver calls set_mac for all slave with bond mac address. But bonding driver set netdev->dev_addr field to its original value, after enslaving interfaces. When ever active slave changes, it swap dev_addr of inactive slave with active. Yet it doesn't notify driver about change in netdev->dev_addr. As netxen driver need to set mac addr when ever interface comes up, it can't rely on netdev->dev_addr field. Specially in case of bonding mode ALB/TLB. Signed-off-by: NNarender Kumar <narender.kumar@qlogic.com> Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Narender Kumar 提交于
Kernel crashes, if promisc mode set without disabling rx queue. Before changing mode in NX2031 chip, wait till rx queue drains. Signed-off-by: NNarender Kumar <narender.kumar@qlogic.com> Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Amit Kumar Salecha 提交于
Avoid resetting memory during initialization, skip this memory block during driver probe. Signed-off-by: NAmit Kumar Salecha <amit@netxen.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 21 11月, 2009 11 次提交
-
-
由 chaithrika@ti.com 提交于
Use BIT for macro definitions wherever possible, remove unused and redundant macros. Signed-off-by: NChaithrika U S <chaithrika@ti.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David J. Choi 提交于
Summary of Changes: -Fix to receive multicast packets by setting the corresponding hardware bit during initialization. -Fix to re-enable the interface [by interface up command(ifup)] while the interface is down. -Fix to be able to down the interface by passing the last parameter correctly to request_irq(). -Remove to read 4 extra bytes from the receiving queue after reading a packet, even though it does not cause a predictable issue now. -Remove occurrences of transmission done interrupt in order to tx throughput enhancement. -Enable IP checksum for packet receiving by setting the corresponding hardware bit during initialization. -Relocate ks_enable_int()/ks_disable_int() in order not to declare those functions at the beginning of the file. -Rename ks_enable()/_disable() to ks_enable_qmu()/ks_disable_qmu() in order to give more meaningful names and relocate them not declaire those functions at the beginning of the file. Signed-off-by: NDavid J. Choi <david.choi@micrel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Geert Uytterhoeven 提交于
When building for Sun 3: drivers/net/ethoc.c:1091: undefined reference to `dma_free_coherent' drivers/built-in.o: In function `ethoc_probe': drivers/net/ethoc.c:965: undefined reference to `dma_alloc_coherent' drivers/net/ethoc.c:1063: undefined reference to `dma_free_coherent' Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
When configuring the OEM bits in the PHY on 82577/82578, do not restart autonegotiation if the firmware is blocking it (e.g. when an IDE-R session is active) because the link must not go down. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
A workaround for pre-release versions of 82577 is causing link issues on some switches. The workaround is no longer needed on production parts so remove it. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
When changing MTU, save it off prior to resetting otherwise the flow control thresholds may be miscalculated. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
On some devices (e.g. 82578) not having a Tx timeout factor when linked at 100Mbps can cause false reports of hardware hangs on busy hubs. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
When flow control (pause) parameters were changed via ethtool (i.e. enabled or disabled), the newly calculated thresholds were not being written to the device for non-fiber media. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
Remove unnecessary workaround that mistakenly does not perform a page select operation for PHY registers 29 and 30 (assuming these are the PHY debug port address and data registers) on 82578 which can cause reads of the Transmit with No Carrier Sense statistics register on page 778 to be read from an incorrect page. Also error out if the page select operation fails. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
Commit 3ec2a2b8 broke Tx/Rx when using jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged once the high water mark was reached preventing normal packet traffic). This patch reverts the breakage and sets appropriate high and low water marks of the Rx FIFO for 82577/82578 which require a workaround due to a flow control issue in hardware. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jaswinder Singh Rajput 提交于
tc is required by CONFIG_IXGBE_DCB. This also fixes compilation warning: drivers/net/ixgbe/ixgbe_main.c: In function ‘ixgbe_tx_is_paused’: drivers/net/ixgbe/ixgbe_main.c:245: warning: unused variable ‘tc’ Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com> Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 11月, 2009 5 次提交
-
-
由 Patrick McHardy 提交于
[ 171.925285] BUG: sleeping function called from invalid context at kernel/mutex.c:280 [ 171.925296] in_atomic(): 1, irqs_disabled(): 0, pid: 671, name: grep [ 171.925306] 2 locks held by grep/671: [ 171.925312] #0: (&p->lock){+.+.+.}, at: [<c10b8acd>] seq_read+0x25/0x36c [ 171.925340] #1: (rcu_read_lock){.+.+..}, at: [<c1391dac>] seq_start+0x0/0x44 [ 171.925372] Pid: 671, comm: grep Not tainted 2.6.31.6-4-netbook #3 [ 171.925380] Call Trace: [ 171.925398] [<c105104e>] ? __debug_show_held_locks+0x1e/0x20 [ 171.925414] [<c10264ac>] __might_sleep+0xfb/0x102 [ 171.925430] [<c1461521>] mutex_lock_nested+0x1c/0x2ad [ 171.925444] [<c1391c9e>] seq_show+0x74/0x127 [ 171.925456] [<c10b8c5c>] seq_read+0x1b4/0x36c [ 171.925469] [<c10b8aa8>] ? seq_read+0x0/0x36c [ 171.925483] [<c10d5c8e>] proc_reg_read+0x60/0x74 [ 171.925496] [<c10d5c2e>] ? proc_reg_read+0x0/0x74 [ 171.925510] [<c10a4468>] vfs_read+0x87/0x110 [ 171.925523] [<c10a458a>] sys_read+0x3b/0x60 [ 171.925538] [<c1002a49>] syscall_call+0x7/0xb Fix it by replacing RCU with nf_log_mutex. Reported-by: N"Yin, Kangkai" <kangkai.yin@intel.com> Signed-off-by: NWu Fengguang <fengguang.wu@intel.com> Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Patrick McHardy 提交于
Return a negative error value. Signed-off-by: NRoel Kluin <roel.kluin@gmail.com> Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
veth_get_stats() can be called in parallel on several cpus. It's better to not reset dev->stats as it could give wrong result on one cpu. Use temporary variables, then store the final results. Also, we should loop on every possible cpus, not only online cpus, or cpu hotplug can suddenly give wrong veth stats. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
ieee802154_fake_xmit() should free skbs since it returns NETDEV_TX_OK Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Acked-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Johannes Berg 提交于
When mac80211 resumes, it currently first sets suspended to false so the driver can start doing things and we can receive frames. However, if we actually receive frames then it can end up starting some work which adds timers and then later runs into a BUG_ON in the timer code because it tries add_timer() on a pending timer. Fix this by keeping track of the resuming process by introducing a new variable 'resuming' which gets set to true early on instead of setting 'suspended' to false, and allow queueing work but not receiving frames while resuming. Reported-by: NMaxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-