Signed-off-by: NJan Engelhardt <jengelh@medozas.de>

It is being superseded by xt_CT (-j CT --notrack).
Signed-off-by: NJan Engelhardt <jengelh@medozas.de>

Signed-off-by: NJan Engelhardt <jengelh@medozas.de>

Two arguments for combining the two:
- xt_mark is pretty useless without xt_MARK
- the actual code is so small anyway that the kmod metadata and the module
  in its loaded state totally outweighs the combined actual code size.

i586-before:
-rw-r--r-- 1 jengelh users 3821 Feb 10 01:01 xt_MARK.ko
-rw-r--r-- 1 jengelh users 2592 Feb 10 00:04 xt_MARK.o
-rw-r--r-- 1 jengelh users 3274 Feb 10 01:01 xt_mark.ko
-rw-r--r-- 1 jengelh users 2108 Feb 10 00:05 xt_mark.o
   text    data     bss     dec     hex filename
    354     264       0     618     26a xt_MARK.o
    223     176       0     399     18f xt_mark.o
And the runtime size is like 14 KB.

i586-after:
-rw-r--r-- 1 jengelh users 3264 Feb 18 17:28 xt_mark.o
Signed-off-by: NJan Engelhardt <jengelh@medozas.de>

Signed-off-by: NJan Engelhardt <jengelh@medozas.de>

Signed-off-by: NJan Engelhardt <jengelh@medozas.de>

Signed-off-by: NJan Engelhardt <jengelh@medozas.de>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert DPRINTK, commonly used for debugging, to netif_<level>
Remove #define PFX
Use #define pr_fmt
Consistently use no periods for non-sentence logging messages
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IEEE 802.3ae clause 45 specifies a somewhat modified MDIO protocol
for use by 10GIGE phys. The main change is a 21 bit address split into
a 5 bit device ID and a 16 bit register offset. The definition is designed
so that normal and extended devices can run on the same MDIO bus.

Extend mdio-bitbang to do the new protocol. At the MDIO bus level the
protocol is requested by or'ing MII_ADDR_C45 into the register offset.

Make phy_read/phy_write/etc pass a full 32 bit register offset.

This does not attempt to make the phy layer support C45 style PHYs, just
to provide the MDIO bus support.

Tested against a Broadcom 10GE phy with ID 0x206034, and several
Broadcom 10/100/1000 Phys in normal mode.
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the PCI runtime power management framework to add basic PCI
runtime PM support to the e1000e driver.  Namely, make the driver
suspend the device when the link is off and set it up for generating
a wakeup event after the link has been detected again.  [This
feature is disabled until the user space enables it with the help of
the /sys/devices/.../power/contol device attribute.]

Based on a patch from Matthew Garrett.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the PCI runtime power management framework to add basic PCI
runtime PM support to the r8169 driver.  Namely, make the driver
suspend the device when the link is not present and set it up for
generating a wakeup event after the link has been detected again.
[This feature is disabled until the user space enables it with the
help of the /sys/devices/.../power/contol device attribute.]
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In mlx4, using char * to store mc address in private structure instead.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I'm not sure this is correct.

It changes logging macros from:
	dev_<level>(&ks->spidev->dev,
to
	netdev_<level>(ks->netdev,

Comments?

Use netdev_<level>
Use netif_<level>
Use pr_<level>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Add missing line to message in ks8851_remove
Change kmalloc/memset(,0) to kzalloc
Remove ks_<level> macros
Consolidation code into set_media_state
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Forward port commit
fc477e160af086f6e30c3d4fdf5f5c000d29beb5
from git://tipc.cslab.ericsson.net/pub/git/people/allan/tipc.git

Origional commit message:

Allow retransmission of cloned buffers

This patch fixes an issue with TIPC's message retransmission logic
that prevented retransmission of clone sk_buffs.  Originally intended
as a means of avoiding wasted work in retransmitting messages that
were still on the driver's outbound queue, it also prevented TIPC
from retransmitting messages through other means -- such as the
secondary bearer of the broadcast link, or another interface in a
set of bonded interfaces.  This fix removes existing checks for
cloned sk_buffs that prevented such retransmission.
Origionally-Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Forward port commit 29eb572941501c40ac6e62dbc5043bf9ee76ee56
from git://tipc.cslab.ericsson.net/pub/git/people/allan/tipc.git

Origional commit message:
Increase frequency of load distribution over broadcast link

This patch enhances the behavior of TIPC's broadcast link so that it
alternates between redundant bearers (if available) after every
message sent, rather than after every 10 messages.  This change helps
to speed up delivery of retransmitted messages by ensuring that
they are not sent repeatedly over a bearer that is no longer working,
but not yet recognized as failed.

Tested by myself in the latest net-2.6 tree using the tipc sanity test suite
Origionally-signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>

bcast.c |   35 ++++++++++++++---------------------
1 file changed, 14 insertions(+), 21 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

`ip -s link` shows interface counters truncated to 32 bit. This is
because interface statistics are transported only in 32-bit quantity
to userspace. This commit adds a new IFLA_STATS64 attribute that
exports them in full 64 bit.

References: http://lkml.indiana.edu/hypermail/linux/kernel/0307.3/0215.htmlSigned-off-by: NJan Engelhardt <jengelh@medozas.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJan Engelhardt <jengelh@medozas.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJan Engelhardt <jengelh@medozas.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We hold RTNL at this point and dont use RCU variants of list traversals,
we dont need rcu_read_lock()/rcu_read_unlock()
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The shared packet statistics are a potential source of slow down
on bridged traffic. Convert to per-cpu array, but only keep those
statistics which change per-packet.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements software receive side packet steering (RPS).  RPS
distributes the load of received packet processing across multiple CPUs.

Problem statement: Protocol processing done in the NAPI context for received
packets is serialized per device queue and becomes a bottleneck under high
packet load.  This substantially limits pps that can be achieved on a single
queue NIC and provides no scaling with multiple cores.

This solution queues packets early on in the receive path on the backlog queues
of other CPUs.   This allows protocol processing (e.g. IP and TCP) to be
performed on packets in parallel.   For each device (or each receive queue in
a multi-queue device) a mask of CPUs is set to indicate the CPUs that can
process packets. A CPU is selected on a per packet basis by hashing contents
of the packet header (e.g. the TCP or UDP 4-tuple) and using the result to index
into the CPU mask.  The IPI mechanism is used to raise networking receive
softirqs between CPUs.  This effectively emulates in software what a multi-queue
NIC can provide, but is generic requiring no device support.

Many devices now provide a hash over the 4-tuple on a per packet basis
(e.g. the Toeplitz hash).  This patch allow drivers to set the HW reported hash
in an skb field, and that value in turn is used to index into the RPS maps.
Using the HW generated hash can avoid cache misses on the packet when
steering it to a remote CPU.

The CPU mask is set on a per device and per queue basis in the sysfs variable
/sys/class/net/<device>/queues/rx-<n>/rps_cpus.  This is a set of canonical
bit maps for receive queues in the device (numbered by <n>).  If a device
does not support multi-queue, a single variable is used for the device (rx-0).

Generally, we have found this technique increases pps capabilities of a single
queue device with good CPU utilization.  Optimal settings for the CPU mask
seem to depend on architectures and cache hierarcy.  Below are some results
running 500 instances of netperf TCP_RR test with 1 byte req. and resp.
Results show cumulative transaction rate and system CPU utilization.

e1000e on 8 core Intel
   Without RPS: 108K tps at 33% CPU
   With RPS:    311K tps at 64% CPU

forcedeth on 16 core AMD
   Without RPS: 156K tps at 15% CPU
   With RPS:    404K tps at 49% CPU

bnx2x on 16 core AMD
   Without RPS  567K tps at 61% CPU (4 HW RX queues)
   Without RPS  738K tps at 96% CPU (8 HW RX queues)
   With RPS:    854K tps at 76% CPU (4 HW RX queues)

Caveats:
- The benefits of this patch are dependent on architecture and cache hierarchy.
Tuning the masks to get best performance is probably necessary.
- This patch adds overhead in the path for processing a single packet.  In
a lightly loaded server this overhead may eliminate the advantages of
increased parallelism, and possibly cause some relative performance degradation.
We have found that masks that are cache aware (share same caches with
the interrupting CPU) mitigate much of this.
- The RPS masks can be changed dynamically, however whenever the mask is changed
this introduces the possibility of generating out of order packets.  It's
probably best not change the masks too frequently.
Signed-off-by: NTom Herbert <therbert@google.com>

 include/linux/netdevice.h |   32 ++++-
 include/linux/skbuff.h    |    3 +
 net/core/dev.c            |  335 +++++++++++++++++++++++++++++++++++++--------
 net/core/net-sysfs.c      |  225 ++++++++++++++++++++++++++++++-
 net/core/skbuff.c         |    2 +
 5 files changed, 538 insertions(+), 59 deletions(-)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create per-cpu workqueue threads instead of a single
krdsd thread. This is a step towards better scalability.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

set_page_dirty() unconditionally re-enables interrupts, so
if we call it with irqs off, they will be on after the call,
and that's bad. This patch moves the call after we've re-enabled
interrupts in send_drop_to(), so it's safe.

Also, add BUG_ONs to let us know if we ever do call set_page_dirty
with interrupts off.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the RDMA op has aborted with a remote access error,
in addition to what we already do (tell userspace it has
completed with an error) also unmap it and put() the rm.

Otherwise, hangs may occur on arches that track maps and
will not exit without proper cleanup.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rds_poll_waitq's listeners will be awoken if we receive a congestion
notification. Bad performance may result because *all* polled sockets
contend for this single lock. However, it should not be necessary to
wake pollers when a congestion update arrives if they have never
experienced congestion, and not putting these on the waitq will
hopefully greatly reduce contention.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems rds_send_drop_to() called
__rds_rdma_send_complete(rs, rm, RDS_RDMA_CANCELED)
with only rds_sock lock, but not rds_message lock. It raced with
other threads that is attempting to modify the rds_message as well,
such as from within rds_rdma_send_complete().
Signed-off-by: NTina Yang <tina.yang@oracle.com>
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RDS's error messages when a connection goes down are a little
extreme. A connection may go down, and it will be re-established,
and everything is fine. This patch links these messages through
rdsdebug(), instead of to printk directly.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

if a machine is shut down without closing sockets properly, and
freeing all MRs, then a BUG_ON will bring it down. This patch
changes these to WARN_ONs -- leaking MRs is not fatal (although
not ideal, and there is more work to do here for a proper fix.)
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a deadlock between rds_rdma_send_complete() and
rds_send_remove_from_sock() when rds socket lock and
rds message lock are acquired out-of-order.
Signed-off-by: NTina Yang <Tina.Yang@oracle.com>
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have two kinds of loopback: software (via loop transport)
and hardware (via IB). sw is used for 127.0.0.1, and doesn't
support rdma ops. hw is used for sends to local device IPs,
and supports rdma. Both are used in different cases.

For both of these, when there is a congestion map update, we
want to call rds_cong_map_updated() but not actually send
anything -- since loopback local and foreign congestion maps
point to the same spot, they're already in sync.

The old code never called sw loop's xmit_cong_map(),so
rds_cong_map_updated() wasn't being called for it. sw loop
ports would not work right with the congestion monitor.

Fixing that meant that hw loopback now would send congestion maps
to itself. This is also undesirable (racy), so we check for this
case in the ib-specific xmit code.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of waking the send thread whenever any send space is available,
wait until it is at least half empty. This is modeled on how
sock_def_write_space() does it, and may help to minimize context
switches.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Other transports use rds_page_copy_user, which updates our
s_copy_to_user counter. TCP doesn't, so it needs to explicity
call rds_stats_add().
Reported-by: NRichard Frank <richard.frank@oracle.com>
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most likely cut n paste error - sendmsg() was checking sock_rcvtimeo.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BUGging on a runtime error code should be avoided. This
patch also eliminates all other BUG()s that have no real
reason to exist.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Otherwise we get a warning from the call in br_forward().
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without CONFIG_BRIDGE_IGMP_SNOOPING,
BR_INPUT_SKB_CB(skb)->mrouters_only is not appropriately
initialized, so we can see garbage.

A clear option to fix this is to set it even without that
config, but we cannot optimize out the branch.

Let's introduce a macro that returns value of mrouters_only
and let it return 0 without CONFIG_BRIDGE_IGMP_SNOOPING.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

route: Fix caught BUG_ON during rt_secret_rebuild_oneshot()

Call rt_secret_rebuild can cause BUG_ON(timer_pending(&net->ipv4.rt_secret_timer)) in
add_timer as there is not any synchronization for call rt_secret_rebuild_oneshot()
for the same net namespace.

Also this issue affects to rt_secret_reschedule().

Thus use mod_timer enstead.
Signed-off-by: NVitaliy Gusev <vgusev@openvz.org>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>