When unregistered with mac80211, we can't call its functionality
for FW restart, so avoid it and prevent automatic FW restart for
the init firmware.
Signed-off-by: NAmit Beka <amit.beka@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There is no need to check if the ownership has been
relinquished but we should rather try to get it in a
loop.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Due to the way the PAN parameters are set up, the
maximum duration isn't 1000 but much lower, set it
to 500 which is safe (somewhere around 550 might
be possible.)
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Until now, the response handler of a Host Command got the
exact same pointer that was also given to the DMA engine.
We almost never need to the Host Command that was sent while
handling its response, but when we do need it, we see that
the command has been modified.

This mystery has been elucidated. The FH (our DMA engine)
writes its meta data on the buffer in the DRAM. Of course it
copies the buffer to the NIC first. This was known to happen
for Tx command, but as a matter of fact, it happens to all
TFD brought by the FH which doesn't care much about what it
brings from DRAM to internal SRAM.

So copy the Host Command to yet another buffer so that we
can properly pass the buffer that was sent originally to the
fw. Do that only if it was request by the user since very
few flows need to get the HCMD sent in the response handler.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Align the code to inside the WARN_ON() as it should.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The generic part of the driver now creates all debugfs
directories. It creates a root directory directly in
the the root of the debugfs filesystem and within that
directories for each device, named after the device ID
of the devices iwlwifi is attached to.

In the cfg80211/mac80211 directory there's now a link
to the toplevel iwlwifi debugfs directory to make it
easier to find the debugfs files.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If registration with mac80211 fails, stop the thermal
throttling and testmode work that were previously started.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This name emphasizes more the role of the function: the
callback called when the ASYNC call to request_firmware
completes.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NDuan Jiong <djduanjiong@gmail.com>

In some rare cases, the CMD_ROC completion may take over 1 second.
The timeout had earlier been increased to 1000ms (from 750ms), but it
is still not enoug.  Increase it to 1500ms.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We need to wait for the command completion event when we send the
CMD_ROLE_STOP event otherwise we may try to send CMD_ROLE_START too
soon and get out-of-sync with the firmware.

In some cases, the firmware may not send the event, so we wait for the
event or for the timeout, whichever comes first.

This patch is based on an earlier version by Eliad.

Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Use this opportunity to consolidate the check for MIMO support into a
separate function.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

handle errors of nla_put() inside the if(nla_put...) {}

This makes the code simpler and clearer because:
we take advantage from the fact that we have only one nla_put
in our routines (so no real need for goto label).
this avoids ugly goto forward followed by goto backward.
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

this completes the calibrator based fem detect logic in driver:
driver starts (by calibrator) in plt_mode PLT_FEM_DETECT
wlcore inits and starts plt on wl12xx
wl12xx fetches fem number from firmware and stores it in wl->fem_manuf
wl12xx immediatly returns (doesn't start radio, etc...)
wlcore returns the fem_manuf to calibrator using WL1271_TM_ATTR_DATA
plt_mode is stopped
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

bip calibration is not required in wl18xx. Therefore we
disable also auto fem (using calibrator fem detect) mode.
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

add wl->plt_mode that is used to indicate different plt
working modes: this will be used to implement calibrator side
auto fem detection where driver asks firmware to detect
the wlan fem radio type and returns it to calibrator.

this is not implemented yet and plt_modes: PLT_ON and
PLT_FEM_DETECT currently behave the same.
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

After the latest mac80211 changes, the sta has
the ap's sta pointer even before association.

This cause the auth and assoc frames to be sent
with the standard ap's rates, rather than the
basic rates.

Change the tx rate policy logic to use the regular
ap rates only for data packets (so control and mgmt
packets will be sent with basic rates)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

During interface removal, don't adjust sleep_auth if we are during
recovery. Since the FW is potentially dead we shouldn't talk to it.
Reported-by: NYossi Wortzel <yossiw@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Initialize val to 0, to remove the following warning with
CONFIG_CC_OPTIMIZE_FOR_SIZE. The compiler used was gcc 4.4.1
(Sourcery G++ Lite 2010q1-202).

drivers/net/wireless/ti/wl18xx/io.c: In function 'wl18xx_top_reg_read':
drivers/net/wireless/ti/wl18xx/io.c:57: warning: 'val' may be used uninitialized in this function
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Send EAPOLs using minimum basic rate for AP, STA, p2p GO and Client.
The patch fixes p2p connection issue with Realtek device in p2p
certification test 5.1.13 (DEVUT reinvokes Persistent Group).
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

ht_mode added to wl18xx conf struct in order to support different modes
from the configuration file, as well as module params, and by default
(working without a conf file and/or no module params).
the hack regarding conf.phy.low_band_component_type for each board
is now explicitly handled after parsing module params.
missing default values to wl18xx config added.
fix string module params not to have defaults (so if empty, param
can be taken from conf file).
update conf version to 3.
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

suspend and resume callbacks configure wakeup conditions to the FW
which may be different between suspend and resume.
This feature is currently not utilized as both in suspend and resume
FW wakeup every 1 DTIM. Avoid waking up the chip and doing the FW command
unless there's an actual difference in the wakeup conditions.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We get DMA alignment trouble if the beginning of the conf.phy struct is
not aligned to 4 bytes. Use kmemdup to ensure alignment.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

b43 with open firmware crashes mac80211 because
it changes the number of queues at runtime which,
while it was never really supported, now crashes
mac80211 due to the new hardware queue logic.

Fix this by detecting open vs. proprietary fw
earlier and registering with mac80211 with the
right number of queues.
Tested-by: NStefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Cc: stable@vger.kernel.org (depends on commit a6f38ac3)
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using work_pending() to defer certain operations when
a HW-reset work has been queued is racy since the check
would return false when the work item is actually in
execution. Use SC_OP_HW_RESET instead to fix this race.
Also, unify the reset debug statistics maintenance.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an interface in AP or P2P-GO mode is removed,
check whether a station interface is already present and
reconfigure the beacon timers etc. properly if it's
associated.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, there are problems with how ANI is handled in
multi-VIF scenarios. This patch addresses them by unifying
the start/stop logic.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove unused variables, use a helper function to choose
the slot and reset beaconing status at one place.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Setup the beacon queue parameters after disabling
interrupts. Also, remove the redundant call in conf_tx()
for IBSS mode since the queue would be configured
with the appropriate cwmin/cwmax values when beaconing
is enabled.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the tx_last_beacon() callback, mac80211's beaconing
status can be used instead. The beacon tasklet doesn't require
it because it is disabled when removing a slot.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* The beaconing status routine is not required, since in
  multi-VIF cases the HW beacon parameters should not be
  re-configured.

* Remove SC_OP_TSF_RESET - when a beaconing interface comes
  up the first time, the TSF has to be reset.

* Simplify ath9k_allow_beacon_config().

* Handle setting/clearing the SWBA interrupt properly.

* Remove the TSF mangling in IBSS mode, it is not required.

* General code cleanup.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cleanup the messy logic dealing with station association
and disassociation.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Do not set/clear TSF when adding/deleting an interface.
  This should be done when the BSS is set up and should also
  take into account the existence of other interfaces.

* Set opmode explicitly.

* ANI setup needs to be decided based on multiple interfaces.
  This can be done via the bss_info_changed() callback.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch revamps interface addition and deletion and simplifies
slot allocation. There is no need to setup the beacon buffer
in add/remove interface, remove this and use simple APIs for
assigning/deleting slots.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Same as the recent ath9k fix
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We found a deadlock in the handling of command failures/reset conditions.
For example:

 1. Two commands are in the queue.
 2. The first command is sent, but causes a timeout, which kicks off an
    asynchronous device reset
 3. The second command is queued (but not yet sent to the hardware)
 4. The device reset kicks in, causing the if_usb disconnect handler to
    set the "surprise removed" flag to be set as the device disappears
    from the bus. This causes lbs_thread to stop processing things
    ("adapter removed; waiting to die"), not processing any further
    commands, leaving the second queued command "in the air", causing a
    deadlock.

Fix this by removing the surpriseremoved flag setting in if_usb. I can't
see any reason why this needs to be done so early. lbs_remove_card will set
this flag at an appropriate time - i.e. after all pending commands have
been completed or cancelled, avoiding this deadlock.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fail commands immediately when the request cannot be sent to the hardware.

This solves the following deadlock:
 1. Two commands are in the queue.
 2. The first command is sent, but causes a timeout, which kicks off an
    asynchronous device reset
 3. The second command is submitted to the device, and fails. The failure
    is noted but the existing code waits for the timeout handler to take
    care of the failure.
 4. The device reset kicks in, causing the device "surprise removed" flag
    to be set as the device disappears from the bus.
 5. lbs_thread notes this and enters "adapter removed; waiting to die"
    mode, without processing any further command timeouts.

While adjusting lbs thread logic to handle this situation may be one way
to fix this, it seems more practical to simplify handling of host_to_card
failure so that the commands are failed immediately without waiting for
more compliated timeout logic to kick in.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

reg_notifier can be called before the interface is up.
Handle this correctly by storing the requested country code, then
apply the relevant configuration when the interface is brought up.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>