This change introduces a few of the less controversial /proc and
/proc/sys interfaces for tile, along with sysfs attributes for
various things that were originally proposed as /proc/tile files.
It also adjusts the "hardwall" proc API.

Arnd Bergmann reviewed the initial arch/tile submission, which
included a complete set of all the /proc/tile and /proc/sys/tile
knobs that we had added in a somewhat ad hoc way during initial
development, and provided feedback on where most of them should go.

One knob turned out to be similar enough to the existing
/proc/sys/debug/exception-trace that it was re-implemented to use
that model instead.

Another knob was /proc/tile/grid, which reported the "grid" dimensions
of a tile chip (e.g. 8x8 processors = 64-core chip).  Arnd suggested
looking at sysfs for that, so this change moves that information
to a pair of sysfs attributes (chip_width and chip_height) in the
/sys/devices/system/cpu directory.  We also put the "chip_serial"
and "chip_revision" information from our old /proc/tile/board file
as attributes in /sys/devices/system/cpu.

Other information collected via hypervisor APIs is now placed in
/sys/hypervisor.  We create a /sys/hypervisor/type file (holding the
constant string "tilera") to be parallel with the Xen use of
/sys/hypervisor/type holding "xen".  We create three top-level files,
"version" (the hypervisor's own version), "config_version" (the
version of the configuration file), and "hvconfig" (the contents of
the configuration file).  The remaining information from our old
/proc/tile/board and /proc/tile/switch files becomes an attribute
group appearing under /sys/hypervisor/board/.

Finally, after some feedback from Arnd Bergmann for the previous
version of this patch, the /proc/tile/hardwall file is split up into
two conceptual parts.  First, a directory /proc/tile/hardwall/ which
contains one file per active hardwall, each file named after the
hardwall's ID and holding a cpulist that says which cpus are enclosed by
the hardwall.  Second, a /proc/PID file "hardwall" that is either
empty (for non-hardwall-using processes) or contains the hardwall ID.

Finally, this change pushes the /proc/sys/tile/unaligned_fixup/
directory, with knobs controlling the kernel code for handling the
fixup of unaligned exceptions.
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

This change enables PCI root complex support for TILEPro.  Unlike
TILE-Gx, TILEPro has no support for memory-mapped I/O, so the PCI
support consists of hypervisor upcalls for PIO, DMA, etc.  However,
the performance is fine for the devices we have tested with so far
(1Gb Ethernet, SATA, etc.).

The <asm/io.h> header was tweaked to be a little bit more aggressive
about disabling attempts to map/unmap IO port space.  The hacky
<asm/pci-bridge.h> header was rolled into the <asm/pci.h> header
and the result was simplified.  Both of the latter two headers were
preliminary versions not meant for release before now - oh well.

There is one quirk for our TILEmpower platform, which accidentally
negotiates up to 5GT and needs to be kicked down to 2.5GT.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

This network (the "UDN") connects all the cpus on the chip in a
wormhole-routed dynamic network.  Subrectangles of the chip can
be allocated by a "create" ioctl on /dev/hardwall, and then to access the
UDN in that rectangle, tasks must perform an "activate" ioctl on that
same file object after affinitizing themselves to a single cpu in
the region.  Sending a wormhole-routed message that tries to leave
that subrectangle causes all activated tasks to receive a SIGILL
(just as they would if they tried to access the UDN without first
activating themselves to a hardwall rectangle).

The original submission of this code to LKML had the driver
instantiated under /proc/tile/hardwall.  Now we just use a character
device for this, conventionally /dev/hardwall.  Some futures planning
for the TILE-Gx chip suggests that we may want to have other types of
devices that share the general model of "bind a task to a cpu, then
'activate' a file descriptor on a pseudo-device that gives access to
some hardware resource".  As such, we are using a device rather
than, for example, a syscall, to set up and activate this code.

As part of this change, the compat_ptr() declaration was fixed and used
to pass the compat_ioctl argument to the normal ioctl.  So far we limit
compat code to 2GB, so the difference between zero-extend and sign-extend
(the latter being correct, eventually) had been overlooked.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

This change is the core kernel support for TILEPro and TILE64 chips.
No driver support (except the console driver) is included yet.

This includes the relevant Linux headers in asm/; the low-level
low-level "Tile architecture" headers in arch/, which are
shared with the hypervisor, etc., and are build-system agnostic;
and the relevant hypervisor headers in hv/.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: NPaul Mundt <lethal@linux-sh.org>