ISP1760 requires a delay of 90ns between programming the address and
reading the data.  Current driver solves this by a mdelay(1) which is
very heavy weighted and slow.  This patch applies the workaround from
the ISP1760 FAQ by using two different banks for PTD and payload data
and using a common wait for them.  This wait is done by an additional
ISP1760 access (whose timing constraints guarantee the 90ns delay).
This improves speed when reading from an USB stick from:

  $ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
  real    1m 15.43s
  user    0m 0.44s
  sys     0m 39.46s

to

  $ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
  real    0m 18.53s
  user    0m 0.16s
  sys     0m 12.97s

[bigeasy@linutronix.de: fixed comment formating, moved define into
   header file, obey 80 char rule]
Signed-off-by: NEnrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: NSebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

if the enqueue function returns -ESHUTDOWN or -ENOMEM then
we return 0 instead of an error. This leads to a timeout and
then to a dequeue request of an not enqueued urb.
Signed-off-by: NSebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1114) fixes a problem that was revealed by an earlier
patch (as1069b).  Some broken controllers seem never to turn off their
RHCS interrupt status bit, even when told to do so.  As a result they
generate an interrupt storm and hang the system.

The patch avoids enabling RHSC interrupt requests when the RHCS status
bit is already set.  This should have no adverse affects on normal
controllers, since they won't set the status bit until a root-hub
status change actually occurs, in which case we wouldn't enable RHSC
interrupt requests anyway -- we would wait until the status change had
been processed and cleared.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If you are using linked lists for queues list_splice() will not do what
you would expect even if you use the elements passed reversed. We need
to handle these differently. We add list_splice_tail() and
list_splice_tail_init().
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file.  Remove these unnecessary
includes.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We want to use WARN() as a variant of WARN_ON(), however a few drivers are
using WARN() internally.  This patch renames these to WARNING() to avoid the
namespace clash.  A few cases were defining but not using the thing, for those
cases I just deleted the definition.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Acked-by: NGreg KH <greg@kroah.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

URB payload data are transfered in wrong byte order on a big endinan
architecture (AVR32).
Signed-off-by: NJulien May <mailinglist@miromico.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A couple of USB register initializations had to be changed on MPC85xx
platforms.  This is due to the internal SoC buses being different on
MPC83xx SoCs vs MPC85xx SoCs.

We currently handle this via an ifdef since 83xx and 85xx are mutually
exclusive kernel builds.
Signed-off-by: NSrikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Copy the OHCI/EHCI PM callbacks of the PCI implementation since
they work equally well on Au1xxx hardware.

Tested on Au1200.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- Fold multiple probe/remove callbacks into one function;
- minor style fixes, no functional changes.

Tested on Au1200.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Various cleanups and fixes to the i2c code in ohci-pnx4008:
* Delete empty isp1301_command. The i2c driver command implementation
  is optional, so there's no point in providing an empty
  implementation.
* Give a name to isp1301_driver. I'm surprised that i2c-core accepted
  to register this driver at all. I've chosen "isp1301_pnx" as the
  name, because it's not a generic ISP1301 driver (much like the
  isp1301_omap driver.) We might want to make the name even more
  specific (but "isp1301_ohci_pnx4008" doesn't fit.)
* The ISP1301 is definitely not a hardware monitoring device.
* Fix a memory leak on failure in isp1301_attach. If
  i2c_attach_client fails, the client is not registered so
  isp1301_detach is never called and the i2c_client memory is lost.
* Use strlcpy instead of strcpy.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

fix interrupt transfer interval for Full/Low speed device.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

fix the problem that did not set IRQF_TRIGGER_ flag.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds support for hardware configurations that don't match the
chip default register settings (e.g., 16-bit data bus, DACK and
DREQ pulled up instead of down, analog overcurrent mode).

These settings are passed in via the OF device tree.  The PCI
interface still assumes the same default values.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

mark this array as const because it is read-only
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Mark the tables as const so that they end up in .rodata
section and don't cacheline share with things that get
written to.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes some performance bugs observed with some workloads
when unlinking EHCI queue header (QH) descriptors from the async ring
(control/bulk schedule).

The mechanism intended to defer unlinking an empty QH (so there is no
penalty in common cases where it's quickly reused) was not working as
intended.  Sometimes the unlink was scheduled:

 - too quickly ... which can be a *strong* negative effect, since
   that QH becomes unavailable for immediate re-use;

 - too slowly ... wasting DMA cycles, usually a minor issue except
   for increased bus contention and power usage;

Plus there was an extreme case of "too slowly":  a logical error in the
IAA watchdog-timer conversion meant that sometimes the unlink never
got scheduled.

The fix replaces a simple counter with a timestamp derived from the
controller's 8 KHz microframe counter, and adjusts the timer usage
for some issues associated with HZ being less than 8K.

(Based on a patch originally by Alan Stern, and good troubleshooting
from  Leonid.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Leonid <leonidv11@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If we do rmmod ohci_hcd while an application is doing something, the
following may happen:

- a control URB completes (in finish_urb) and the ohci's endpoint is
  set into ED_UNLINK in ed_deschedule
- same URB is (re)submitted because of the open/close loop or other
  such application behaviour
- rmmod sets the state to HC_STATE_QUESCING
- finish_unlinks happens at next SOF; normally it would set ed into
  ED_IDLE and immediately call ed_schedule (since URB had extra TDs
  queued), which sets it into ED_OPER. But the check in ed_schedule
  makes it fail with -EAGAIN (which is ignored)
- from now on we have a dead URB stuck; it cannot even be unlinked
  because the ed status is not ED_OPER, and thus start_ed_unlink is
  not invoked.

This patch removes the check. In 2.6.25, all callers check for
__ACTIVE bit before invoking ed_schedule, which is more appropriate.

Alan Stern and David Brownell approved of this (cautiously).
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As RMK pointed out,  considering the fact that the _only_ platform with
a PXA and SA1111 is the Lubbock, and that SA1111 DMA doesn't work there,
(i.e. the SA1111 OHCI doesn't work there) the SA1111 OHCI driver should
really be made SA11x0 specific.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Looks like usb_put_hcd was missing. Also, make an always-zero function
return void.
Signed-off-by: NPete Zaitcev <zaitcev@yahoo.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch makes the following needlessly global functions static:
- enqueue_an_ATL_packet()
- enqueue_an_INT_packet()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NSebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The bus_id field is going away, use the dev_set_name() function
to set it properly.
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The bus_id field is going away, use the dev_name() function instead.
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch was created by

	git grep -E -l 'Rus(el|s?e)l King' | xargs -r -t perl -p -i -e 's/Rus(el|s?e)l King/Russell King/g'
Signed-off-by: NUwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Most-Definitely-Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit e8721549.

Andrey Borzenkov reports that it resulted in a totally hung machine for
him when loading the OHCI driver.  Extensive netconsole capture with
SysRq output shows that modprobe gets stuck in ohci_hub_status_data()
when probing and enabling the OHCI controller, see for example

	http://lkml.org/lkml/2008/7/5/236

for an analysis.

The problem appears to be an interrupt flood triggered by the commit
that gets reverted, and Andrey confirmed that the revert makes things
work for him again.
Reported-and-tested-by: NAndrey Borzenkov <arvidjaar@mail.ru>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes a problem with OHCI where canceling bulk or
interrupt URBs may lose track of the right data toggle.  This
seems to be a longstanding bug, possibly dating back to the
Linux 2.4 kernel, which stayed hidden because

 (a) about half the time the data toggle bit was correct;
 (b) canceling such URBs is unusual; and
 (c) the few drivers which cancel these URBs either
      [1] do it only as part of shutting down, or
      [2] have fault recovery logic, which recovers.

For those transfer types, the toggle is normally written back
into the ED when each TD is retired.  But canceling bypasses
the mechanism used to retire TDs ... so on average, half the
time the toggle bit will be invalid after cancelation.

The fix is simple:  the toggle state of any canceled TDs are
propagated back to the ED in the finish_unlinks function.

(Issue found by leonidv11@gmail.com ...)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Leonid <leonidv11@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes a regression in the EHCI driver's TIMER_IO_WATCHDOG
behavior.  The patch "USB: EHCI: add separate IAA watchdog timer" changed
how that timer is handled, so that short timeouts on the remaining
timer (unfortunately, overloaded) would never be used.

This takes a more direct approach, reorganizing the code slightly to
be explicit about only the I/O watchdog role now being overridable.
It also replaces a now-obsolete comment describing older timer behavior.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Leonid <leonidv11@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the SM501 and another platform driver, such as the SM501
then we end up defining PLATFORM_DRIVER twice. This patch
seperated the SM501 onto a seperate define of SM501_OHCI_DRIVER
so that it can be selected without overwriting the original
definition.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Change omap USB code to use omap_read/write instead of __REG for multi-omap

Cc: David Brownell <david-b@pacbell.net>
Cc: linux-usb@vger.kernel.org
Cc: i2c@lm-sensors.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

and include pxa2xx-regs.h as build fix since PSSR definitions
moved from pxa-regs.h into pxa2xx-regs.h.

Note: This change is temporary as pxa27x processor specific
code will be finally moved elsewhere (both drivers should
support pxa3xx, too).
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This fixes the bogus "io mem 0x00000000" message printed
during driver init due to hcd->rsrc_start being assigned after
the call to usb_add_hcd().
Signed-off-by: NNate Case <ncase@xes-inc.com>
Acked-by: NSebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

R8A66597 is similar to SH7723 USB 2.0 Host/Function module.
In addition, the USB of SH7366 is compatible with SH7723.
It can support SH7723 USB host by changing Kconfig.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit fa38dfcc.

It wasn't really a regression and David and Alan are still working
through the issues reported.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>