The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
  drivers/net/wireless/ath5k/base.c
  drivers/net/wireless/b43/main.c
  drivers/net/wireless/ipw2100.c
  drivers/net/wireless/ipw2200.c
  drivers/net/wireless/iwlwifi/iwl-3945.c
  drivers/net/wireless/iwlwifi/iwl-4965.c
  drivers/net/wireless/iwlwifi/iwl-5000.c
  drivers/net/wireless/iwlwifi/iwl-agn.c
  drivers/net/wireless/iwlwifi/iwl-core.c
  drivers/net/wireless/iwlwifi/iwl-eeprom.c
  drivers/net/wireless/iwlwifi/iwl-hcmd.c
  drivers/net/wireless/iwlwifi/iwl-power.c
  drivers/net/wireless/iwlwifi/iwl3945-base.c

This patch removes the said #include <version.h>.
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

txdone_entry_desc_flags is used with __set_bit and test_bit which
bit-shift the values, so don't bit-shift the flags in the enum.
Also make sure flags are initialized before being used.
Signed-off-by: NJochen Friedrich <jochen@scram.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In trying to help users on the Ubuntu Bugzilla, I discovered another
BCM4306 with the Bluetooth Coexistence programming error in the SPROM.

This patch is contingent on the one that added the Linksys device with
subdevice code of 0x0014.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE was made unnecessary in
the recent revamp on beacon configuration.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

(Only important for USB V1 Adaptors)

If an incoming frame wasn't accepted by p54_rx function
the skb will be reused for new frames...

But, we must not forget to set the skb's data pointers into
the same state in which it was initialized by p54u_init_urbs.

Otherwise we either end up with 16 bytes less on every requeue,
or if a new frame is worthy enough to be accepted, the data is
in the wrong place (urb->transfer_buffer wasn't updated!) and mac80211
has a hard time to recognize it...
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

priv->tx_hdr_len is set by the driver _after_ it called p54_init_common.
While this isn't much a problem for any PCI or ISL3887 cards/sticks,
because they don't need any extra header and therefore tx_hdr_len is
zero for them...
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add newlines at printk outputs to not break dmesg.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the USB ID for a Netgear WG111v3.
Signed-off-by: Nmatthieu Barthélemy <bonsouere@gmail.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Linksys WMP54G (BCM4306/3) card in a PCI format has an SPROM coding
error and needs the fix found for several other cards.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>		[2.6.25.x, 2.6.26.x]
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes needless probe request caused by zero value in
sta->last_rx inside ieee80211_associated flow
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 256b152b (ath5k: don't enable
MSI, we cannot handle it yet) has removed msi support, but overlooked
the suspend/resume code. This patch completes msi removal.

I don't consider this patch copyrightable, and thus put it into the
public domain. The result is of course a base.c file dual-licensed under
3-clause-BSD and GPL.
Signed-off-by: NMichael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Makes ssb work on system without a PCI bus.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Guard rfkill controllers attached to a rfkill class against state changes
after class suspend has been issued.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit b19fa1fa, entitled "net: Delete NETDEVICES_MULTIQUEUE kconfig
option" breaks p54pci and p54usb.

Additionally, the old logic always tx'ed cts frames (if enabled)
with a short preamble when [rate > 3]. (i.e. with any 802.11g rate).
Of course this isn't that bad, but it's still wrong!

(This patch also clarifies the meanings of some of the fields in the tx
header for the hardware. -- JWL)
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: <stable@kernel.org>		[2.6.25.x, 2.6.26.x]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

(I missed the fact that the original post said to apply this patch
twice... -- JWL)

Original commit log message:

This patch works around an internal compiler error (gcc bug #37014) in
all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1
on at least powerpc and mips.

Many thanks to Andrew Pinski for analyzing the gcc bug.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch updates the version number to 3.94.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethtool stats are 64-bits in length.  net_device_stats members are
unsigned long types.  When gathering information for
a get_ethtool_stats call, the driver will call a driver-private,
inlined get_stat64() function, which returns an unsigned long value.
This call will inadvertently mask off the upper 32-bits of a stat on
32-bit machines.

This patch defines a new get_estat() inline function and modifies the
ESTAT_ADD() macro to use it.
Signed-off-by: NStefan Buehler <stbuehler@web.de>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The git commit 7c5026aa ("tg3: Add
link state reporting to UMP firmware") introduced code that waits for
previous firmware events to be serviced before attempting to submit a
new event.  Unfortunately that patch contained a bug that cause the
driver to wait 2.5 seconds, rather than 2.5 milliseconds as intended.
This patch fixes that bug.

This bug revealed that not all firmware versions service driver events
though.  Since we do not know which versions of the firmware do and don't
service these events, the driver needs some way to minimize the effects
of the delay.  This patch solves the problem by recording a jiffies
timestamp when it submits an event to the hardware.  If the jiffies
counter shows that 2.5 milliseconds have already passed, a wait is not
needed and the driver can proceed to submit a new event.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ENABLE_ASF flag is set when DASH is enabled on the NIC, but DASH
does not run on the RX CPU.  Instead it runs on the APE.
Consequently, the driver does not need to send "driver alive" updates
to the RX CPU when the APE is present.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcom's DASH (Desktop and mobile Architecture for System Hardware)
implementation requires that the driver preserve particular register
settings.  If the driver does not preserve them, communication with
the DASH firmware will be lost.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recently, more status bits have been added to the APE status register.
This patch refines the status register check so that the driver can
send more events than it would have otherwise.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the driver resets the chip while the APE is performing a register
access, that register access will never complete and the APE will hang
indefinitely.  To prevent this race condition, the driver must acquire
an APE mutex before resetting the chip.  The APE will not attempt a
register access until it acquires this lock.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let me first state that disabling the route cache hash rebuild
should not be done without extensive analysis on the risk profile
and careful deliberation.

However, there are times when this can be done safely or for
testing.  For example, when you have mechanisms for ensuring
that offending parties do not exist in your network.

This patch lets the user disable the rebuild if the interval is
set to zero.  This also incidentally fixes a divide-by-zero error
with name-spaces.

In addition, this patch makes the effect of an interval change
immediate rather than it taking effect at the next rebuild as
is currently the case.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a bug with spin_lock_bh() inserted instead of spin_unlock_bh() by
some recent patch. 
Reported-by: NDenys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ipv6_dev_get_saddr() blindly de-references dst_dev to get the network
namespace, but some callers might pass NULL.  Change callers to pass a
namespace pointer instead.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In certain cases when ASF or other management firmware is running, the
chip may be configured to always strip out the VLAN tag even when
VLAN acceleration is not enabled.  This causes some VLAN tagged
packets to be received by the host stack without any knowledge that
the original packet was VLAN tagged.

We fix this by re-inserting the VLAN tag into the packet when necessary.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should now be checking BNX2_FLAG_CAN_KEEP_VLAN to determine how
to set the VLAN rx tagging in the RX_MODE register.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a pair of nasty locking problems in the ax88796 driver
spotted by a sparse check:

warning: context imbalance in 'ax_get_settings' - wrong count at exit
warning: context imbalance in 'ax_set_settings' - wrong count at exit
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

After some cleanups in arch/mips area, now MACH_TX49XX is selected for
both TOSHIBA_RBTX4927 and TOSHIBA_RBTX4938.  Fold these two conditions
to one.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Move the Kconfig for the new "Option" driver so it's not in the
middle of the usbnet-based drivers, so the dependency displays
in the Kconfig user interfaces don't get trashed.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix up problems in hso.c driver as pointed out by Andrew.

Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

As recommended by Arjan.

Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The references on ttyHSx devices were not decremented correctly when
the tty was closed. The helper freeing the serial devices was never
called because of that, and the module left some dangling sysfs
devices after being unloaded.
Signed-off-by: NOlivier Blin <blino@mandriva.com>
Cc: Jari Tenhunen <jari.tenhunen@iki.fi>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The tty may be closed already when the read/write callbacks are called.
This patch checks that the ttys still exist before waking them up.
Signed-off-by: NOlivier Blin <blino@mandriva.com>
Acked-by: NAlan Cox <alan@redhat.com>
Cc: Jari Tenhunen <jari.tenhunen@iki.fi>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

There doesn't seem to be a compelling reason why atl1e_setup_mac_ctrl()
is marked as "inline":

It's not used in any place where speed would matter much, and as long as
it has only one caller non-ancient gcc versions anyway inline it
automatically.

This patch fixes the following compile error with gcc 3.4:

<--  snip  -->

...
  CC      drivers/net/atl1e/atl1e_main.o
atl1e_main.c: In function `atl1e_check_link':
atl1e_main.c:50: sorry, unimplemented: inlining failed in call to
atl1e_main.c:196: sorry, unimplemented: called from here
make[4]: *** [drivers/net/atl1e/atl1e_main.o] Error 1

<--  snip  -->
Reported-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Raise driver version to 4.0.11.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>