Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 31 5月, 2006 26 次提交
    • T
      [PATCH] libata-hp: implement bootplug · 3e706399
      由 Tejun Heo 提交于 
      Implement bootplug - boot probing via hotplug path.  While loading,
ata_host_add() simply schedules probing and invokes EH.  After EH
completes, ata_host_add() scans and assicates them with SCSI devices.
EH path is slightly modified to handle this (e.g. no autopsy during
bootplug).  The SCSI part is left in ata_host_add() because it's
shared with legacy path and to keep probing order as before (ATA scan
all ports in host_set then attach all).
Signed-off-by: NTejun Heo <htejun@gmail.com>
      3e706399
    • T
      [PATCH] libata-hp: hook warmplug · ccf68c34
      由 Tejun Heo 提交于 
      Hook transportt->user_scan() and hostt->slave_destroy().
Signed-off-by: NTejun Heo <htejun@gmail.com>
      ccf68c34
    • T
      [PATCH] libata-hp: implement warmplug · 83c47bcb
      由 Tejun Heo 提交于 
      Implement warmplug.  User-initiated unplug can be detected by
hostt->slave_destroy() and plug by transportt->user_scan().  This
patch only implements the two callbacks.  The next function will hook
them.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      83c47bcb
    • T
      [PATCH] libata-hp: implement SCSI part of hotplug · 580b2102
      由 Tejun Heo 提交于 
      Implement SCSI part of hotplug.

This must be done in a separate context as SCSI makes use of EH during
probing.  SCSI scan fails silently if EH is in progress.  In such
cases, libata pauses briefly and retries until every device is
attached.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      580b2102
    • T
      [PATCH] libata-hp: implement hotplug · 084fe639
      由 Tejun Heo 提交于 
      Implement ATA part of hotplug.  To avoid probing broken devices over
and over again, disabled devices are not automatically detached.  They
are detached only if probing is requested for the device or the
associated port is offline.  Also, to avoid infinite probing loop,
Each device is probed only once per EH run.

As SATA PHY status is fragile, devices are detached only after it has
used up its recovery chances unless explicitly requested by LLDD or
user (LLDD may request direct detach if, for example, it supports cold
presence detection).
Signed-off-by: NTejun Heo <htejun@gmail.com>
      084fe639
    • T
      [PATCH] libata-hp: implement ata_eh_detach_dev() · 0ea035a3
      由 Tejun Heo 提交于 
      Implement ata_eh_detach_dev().  This function is responsible for
detaching an ATA device and offlining the associated SCSI device
atomically so that the detached device is not accessed after ATA
detach is complete.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      0ea035a3
    • T
      [PATCH] sata_sil24: update sil24_hardreset() · e8e008e7
      由 Tejun Heo 提交于 
      Use phy debouncing instead of unconditional wait after DEV_RST and
make sil24_hardreset() to request followup SRST as that's the only way
to wait for !BSY.  Note that the original implementation never worked
- if the cached status was !BSY, ata_busy_sleep() finished
immediately; otherwise, it timed out regardless of the actual device
status.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      e8e008e7
    • T
      [PATCH] sata_sil24: rename PORT_PRB to PORT_LRAM and add PORT_LRAM_SLOT_SZ · 135da345
      由 Tejun Heo 提交于 
      PORT_PRB is a misnomer as the area also contains other stuff.  Rename
it to PORT_LRAM and add PORT_LRAM_SLOT_SZ.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      135da345
    • T
      [PATCH] sata_sil: new interrupt handler · cbe88fbc
      由 Tejun Heo 提交于 
      The DMA complete bit of these controllers reflects ATA IRQ status
while no DMA command is in progress.  So, we can tell whether the
controller is raising an interrupt or not in deterministic manner.
This patch gives sata_sil its own interrupt handler which behaves much
better than the original one in terms of error detection and handling.
This change is also necessary for later hotplug support.

Further improvements are possible, in both 2 and 4 ports versions, we
can get all status with only one readl and using custom bmdma
operations can further cut down register accesses.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      cbe88fbc
    • T
      [PATCH] sata_sil: add new constants in preparation for new interrupt handler · 20888d83
      由 Tejun Heo 提交于 
      sata_sil is about to get a brand new interrupt handler.  Add relevant
constants.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      20888d83
    • T
      [PATCH] libata: export ata_hsm_move() · 9a1004d0
      由 Tejun Heo 提交于 
      ata_hsm_move() will be used by LLDDs which depend on standard PIO HSM
but implement their own interrupt handlers.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      9a1004d0
    • T
      [PATCH] libata-hp-prep: implement followup softreset handling · 664faf09
      由 Tejun Heo 提交于 
      In some cases, hardreset must be followed by SRST.

* some controllers can't classify with hardreset
* some controllers can't wait for !BSY after hardreset (LLDD should
  explicitly request followup softreset by returning -EAGAIN)
* (later) PM needs SRST w/ PMP==15 to operate after hardreset

To handle above cases, this patch implements follow-up softreset.
After a hardreset, ata_eh_reset() checks whether any of above
conditions are met and do a follow-up softreset if necessary.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      664faf09
    • T
      [PATCH] libata-hp-prep: add prereset() method and implement ata_std_prereset() · f5914a46
      由 Tejun Heo 提交于 
      With hotplug, every reset might be a probing reset and thus something
similar to probe_init() is needed.  prereset() method is called before
a series of resets to a port and is the counterpart of postreset().
prereset() can tell EH to use different type of reset or skip reset by
modifying ehc->i.action.

This patch also implements ata_std_prereset().  Most controllers
should be able to use this function directly or with some wrapping.
After hotplug, different controllers need different actions to resume
the PHY and detect the newly attached device.  Controllers can be
categorized as follows.

* Controllers which can wait for the first D2H FIS after hotplug.
  Note that if the waiting is implemented by polling TF status, there
  needs to be a way to set BSY on PHY status change.  It can be
  implemented by hardware or with the help of the driver.

* Controllers which can wait for the first D2H FIS after sending
  COMRESET.  These controllers need to issue COMRESET to wait for the
  first FIS.  Note that the received D2H FIS could be the first D2H
  FIS after POR (power-on-reset) or D2H FIS in response to the
  COMRESET.  Some controllers use COMRESET as TF status
  synchronization point and clear TF automatically (sata_sil).

* Controllers which cannot wait for the first D2H FIS reliably.
  Blindly issuing SRST to spinning-up device often results in command
  issue failure or timeout, causing extended delay.  For these
  controllers, ata_std_prereset() explicitly waits ATA_SPINUP_WAIT
  (currently 8s) to give newly attached device time to spin up, then
  issues reset.  Note that failing to getting ready in ATA_SPINUP_WAIT
  is not critical.  libata will retry.  So, the timeout needs to be
  long enough to spin up most devices.

LLDDs can tell ata_std_prereset() which of above action is needed with
ATA_FLAG_HRST_TO_RESUME and ATA_FLAG_SKIP_D2H_BSY flags.  These flags
are PHY-specific property and will be moved to ata_link later.

While at it, this patch unifies function typedef's such that they all
have named arguments.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      f5914a46
    • T
      [PATCH] libata-hp-prep: implement sata_phy_debounce() · d7bb4cc7
      由 Tejun Heo 提交于 
      With hotplug, PHY always needs to be debounced before a reset as any
reset might find new devices.  Extract PHY waiting code from
sata_phy_resume() and extend it to include SStatus debouncing.  Note
that sata_phy_debounce() is superset of what used to be done inside
sata_phy_resume().

Three default debounce timing parameters are defined to be used by
hot/boot plug.  As resume failure during probing will be properly
handled as errors, timeout doesn't have to be long as before.
probeinit() uses the same timeout to retain the original behavior.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      d7bb4cc7
    • T
      [PATCH] libata-hp-prep: make probing related functions global · a9beec95
      由 Tejun Heo 提交于 
      Hotplug will be implemented in libata-eh.c.  Make ata_dev_read_id()
and ata_dev_configure() global.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      a9beec95
    • T
      [PATCH] libata-hp-prep: add ata_aux_wq · 453b07ac
      由 Tejun Heo 提交于 
      It's best to run ATA hotplug from EH but attaching SCSI devices needs
working EH.  ata_aux_wq is used to give SCSI hotplug operations a
separate context.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      453b07ac
    • T
      [PATCH] libata-hp-prep: store attached SCSI device · 3edebac4
      由 Tejun Heo 提交于 
      Add device persistent field dev->sdev and store the attached SCSI
device.  With hotplug, libata needs to know the attached SCSI device
to offline and detach it, but scsi_device_lookup() cannot be used
because libata will reuse SCSI ID numbers - dead but not gone devices
(due to zombie opens, etc...) interfere with the lookup.

dev->sdev doesn't hold reference to the SCSI device.  It's cleared
when the SCSI device goes away.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      3edebac4
    • T
      [PATCH] libata-hp-prep: implement ap->hw_sata_spd_limit · 5a04bf4b
      由 Tejun Heo 提交于 
      Add ap->hw_sata_spd_limit and initialize it once during the boot
initialization (or driver load initialization).  ap->sata_spd_limit is
reset to ap->hw_sata_spd_limit on hotplug.  This prevents spd limits
introduced by earlier devices from affecting new devices.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      5a04bf4b
    • T
      [PATCH] libata-hp-prep: use __ata_scsi_find_dev() · 31534363
      由 Tejun Heo 提交于 
      Convert direct sdev -> dev lookup to __ata_scsi_find_dev().
Signed-off-by: NTejun Heo <htejun@gmail.com>
      31534363
    • T
      [PATCH] libata-hp-prep: update ata_scsi_find_dev() and friends · ab5b3a5b
      由 Tejun Heo 提交于 
      Separate out ata_find_dev() and __ata_scsi_find_dev() from
ata_scsi_find_dev().  These will be used by later hotplug
implementation.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      ab5b3a5b
    • T
      [PATCH] libata-hp-prep: make some ata_device fields persistent · 72fa4b74
      由 Tejun Heo 提交于 
      Lifetimes of some fields span over device plugging/unplugging.  This
patch moves such persistent fields to the top of ata_device and
separate them with ATA_DEVICE_CLEAR_OFFSET.  Fields above the offset
are initialized once during host initializatino while all other fields
are cleared before hotplugging.  Currently ->ap, devno and part of
flags are persistent.

Note that flags is partially cleared while holding host_set lock.
This is to synchronize with later warm plug implementation which will
record hotplug request in dev->flags.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      72fa4b74
    • T
      [PATCH] libata-hp-prep: implement ata_dev_init() · 3ef3b43d
      由 Tejun Heo 提交于 
      Move initialization of struct ata_device into ata_dev_init() in
preparation for hotplug.  This patch calls ata_dev_init() from
ata_host_init() and thus makes no functional difference.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      3ef3b43d
    • T
      [PATCH] libata-hp-prep: add flags and eh_info/context fields for hotplug · abdda733
      由 Tejun Heo 提交于 
      Add hotplug related flags and eh_info/context fields.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      abdda733
    • T
      [PATCH] libata: implement ata_eh_wait() · c6cf9e99
      由 Tejun Heo 提交于 
      Implement ata_eh_wait().  On return from this function, it's
guaranteed that the EH which was pending or in progress when the
function was called is complete - including the tailing part of SCSI
EH.  This will be used by hotplug and others to synchronize with EH.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      c6cf9e99
    • T
      [PATCH] libata: shift host flag constants · 7395acb2
      由 Tejun Heo 提交于 
      Nudge host flag constants to make a room after ATA_FLAG_EH_PENDING.
New EH flag will be added.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      7395acb2
    • T
      [PATCH] libata: set PIO-0 after successful EH reset · 20952b69
      由 Tejun Heo 提交于 
      Set ata_device->pio_mode to XFER_PIO_0 after a successful reset.  This
is to keep EH resets consistent with probe resets as updated by the
commit b6079ca4.  Note that, with
soon-to-follow hotplug update, EH resets will include probe resets.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      20952b69
  3. 29 5月, 2006 6 次提交
  5. 28 5月, 2006 1 次提交
  7. 27 5月, 2006 7 次提交