Fix posting lists of > 255 receive WRs for Tavor: rq.next_ind must
be updated each doorbell, otherwise the next doorbell will use an
incorrect index.

Found by Ronni Zimmermann at Mellanox.
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Several checks in the rdma_cm check against the state of the
cm_id, but only to validate that the cm_id is bound to an underlying
transport specific CM and an RDMA device.  Make the check explicit
in what we're trying to check for, since we're not synchronizing
against the cm_id state.

This will allow a user to disconnect a cm_id or reject a connection
after receiving a device removal event.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The cma_iw_handler needs to validate the state of the rdma_cm_id before
processing a new connection request to ensure that a device removal is
not already being processed for the same rdma_cm_id.  Without the state
check, the user can receive simultaneous callbacks for the same cm_id, or
a callback after they've destroyed the cm_id.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a new routine and rename another to encapsulate common code for
synchronizing with device removal.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

- Scaling code is still considered experimental, so disable it by default
- Increase version to SVNEHCA_0023
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

eHCA's sysfs attributes are now being created via sysfs_create_group(),
making the process neatly table-driven. The return value is checked, thus
fixing a few compiler warnings.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

- In ehca_process_eq(), we're IRQ safe throughout the whole function, so we
  don't need another _irqsave in the middle of flight.

- take_over_work() is only called by comp_pool_callback(), so it can move
  into the same #ifdef block.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

AQP0/1 should report qp_num={0|1} and the actual QP# should be stored
in struct ehca_qp, not the other way round.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The driver needs to always supply the "GRH present" flag to the
hypervisor, whether it's true or false. Not supplying it (i.e. not
setting the corresponding mask bit) amounts to a "perhaps", which we
don't want.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Some pSeries hypervisor versions show a race condition in the allocate
MR hCall.  Serialize this call per adapter to circumvent this problem.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Once upon a time, GPIO interrupts were rare.  But then a chip bug in
the waldo series forced the use of a GPIO interrupt to signal packet
reception.  This greatly increased the frequency of GPIO interrupts
which have the gpio_mask bits set on the waldo chips.  Other bits in
the gpio_status register are used for I2C clock and data lines, these
bits are usually on.  An "unlikely" annotation leftover from the old
days was improperly applied to these bits, and an unnecessary chip
mmio read was being accessed in the interrupt fast path on waldo.

Remove the stagnant unlikely annotation in the interrupt handler and
keep a shadow copy of the gpio_mask register to avoid the slow mmio
read when testing for interruptable GPIO bits.
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

uar_lock spinlock was used in mlx4_ib_cq_arm without being initialized
(this only affects 32-bit archs, because uar_lock is not used on
64-bit archs and MLX4_INIT_DOORBELL_LOCK() is a NOP).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

struct mlx4_priv.doorbell_lock is never used, so delete it.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

CONFIG_MLX4_DEBUG works out to a def_bool y for those that have 
CONFIG_EMBEDDED set.  Make it depend on MLX4_CORE.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
  IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters
  IB: Put rlimit accounting struct in struct ib_umem
  IB/uverbs: Export ib_umem_get()/ib_umem_release() to modules

* 'usb-move' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  Move USB network drivers to drivers/net/usb.

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  Doc Fix: remove mention of combined mode-related kernel parameters
  libata: fix kernel-doc parameters
  Fix pata_qdi.c probe code
  pata_scc: fix compilation
  sata_via: add missing PM hooks
  sata_nv: fix ADMA freeze/thaw/irq_clear issues
  pata_pcmcia.c: add card ident for jvc cdrom
  sata_promise: SATAII-150/300 TX4 port numbering fix
  sata_promise: fix another error decode regression
  libata-acpi: fix _GTF command protocol for ATAPI devices

This reverts commit 5b479c91.

Quoth Neil Brown:

  "It causes an oops when auto-detecting raid arrays, and it doesn't
   seem easy to fix.

   The array may not be 'open' when do_md_run is called, so
   bdev->bd_disk might be NULL, so bd_set_size can oops.

   This whole approach of opening an md device before it has been
   assembled just seems to get more and more painful.  I think I'm going
   to have to come up with something clever to provide both backward
   comparability with usage expectation, and sane integration into the
   rest of the kernel."
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It is preferable to group drivers by usage (net, scsi, ATA, ...) than
by bus.  When reviewing drivers, the [PCI|USB|PCMCIA|...] maintainer
is probably less qualified on networking issues than a networking
maintainer.  Also, from a practical standpoint, chips often
appear on multiple buses, which is why we do not put drivers into
drivers/pci/net.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Looks like you removed the combined_mode quirk (yay!) but didn't update
kernel-parameters.txt...  might confuse people.  Here's a patch to remove
mention of it from the documentation.
Signed-off-by: NJesse Barnes <jesse.barnes@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Warning(linux-2.6.21-git4//drivers/ata/libata-core.c:904): No description found for parameter 'new_sectors'
Warning(linux-2.6.21-git4//drivers/ata/libata-core.c:941): No description found for parameter 'new_sectors'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There is a small typo in the probe code of pata_qdi.c, here is a patch.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

For some reason, sata_via is missing PM hooks.  Add them.  Spotted by
Jeroen Janssen <jeroen.janssen@gmail.com>.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Jeroen Janssen <jeroen.janssen@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes some problems with ADMA-capable controllers with
regard to freeze, thaw and irq_clear libata callbacks. Freeze and
thaw didn't switch the ADMA-specific interrupts on or off, and more
critically the irq_clear function didn't respect the restriction that
the notifier clear registers for both ports have to be written at
the same time even when only one port is being cleared. This could
result in timeouts on one port when error handling (i.e. as a result
of hotplug) occurred on the other port.

As well, this fixes some issues in the interrupt handler: we shouldn't
check any ADMA status if the port has ADMA switched off because of
an ATAPI device, and it also checks to see if any ADMA interrupt has
been raised even when we are in port-register mode.
Signed-off-by: NRobert Hancock <hancockr@shaw.ca>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

update pata_pcmcia to add card ident for JVC MP-CDX1 cdrom drive
card info:
PRODID_1="KME"
PRODID_2="KXLC005"
PRODID_3="00"
MANFID=0032,2904
Signed-off-by: NRichard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There is a known problem with sata_promise on SATAII-150/300 TX4
controller cards: it enumerates drives in an order that differs
from the port numbers printed on the controller cards. However,
Promise's BIOS and Linux driver both get the order right.

I investigated Promise's Linux driver (v1.01.0.23), and found
that it explicitly changes the mapping from logical port number
to ATA engine MMIO address on the SATAII TX4 cards. It does this
on all SATAII TX4 cards, without inspecting revision etc. The
SATAII TX2plus cards continue to use the same mapping that was
used for the first-generation chips.

This patch updates sata_promise to use the new port number to
ATA engine mapping on SATAII TX4 cards, which fixes the drive
enumeration order problem on those cards. Tested on several
1st and 2nd generation TX2plus and TX4 chips.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The sata_promise error decode update changed pdc_host_intr()
to return and not complete the qc after detecting an error.
Unfortunately not completing the qc:s causes them to always
time out on error, which is wrong and has nasty side-effects.

This patch updates pdc_error_intr() to call ata_port_abort(),
similar to ahci and sata_sil24. Doing this is important as it
makes EH see the original error and not a bogus timeout.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

_GTF command is never ATA_PROT_ATAPI_NODATA whether the device is
ATAPI or not.  It's always ATA_PROT_NODATA.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Copied from b44 driver, but it works:

netconsole: device eth0 not up yet, forcing it
atl1: eth0 link is up 100 Mbps full duplex
netconsole: network logging started
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Ejecting a PCMCIA IBM Token Ring card that has not had its dev->open()
called will reliably trigger an uninitialized spinlock oops when
spinlock debugging is enabled. The system then hangs, occasionally
softlockup oopsing.  Apparently ibmtr.c:tok_interrupt() doesn't expect
to be called before tok_open(), but tok_interrupt() gets called anyway
when the card is ejected.  So, set an already-existing flag which
causes tok_interrupt() to bail out early upon card ejection. Tested by
inserting and removing the PCMCIA card several times.
Signed-off-by: NPaul Walmsley <paul@booyaka.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

By default, the skge driver now enables wake on magic and wake on PHY.
This is a bad default (bug), wake on PHY means machine will never shutdown
if connected to a switch.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>a
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Merge branch 'upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: fix PIO setup on resume for ATAPI devices
  ide: legacy PCI bus order probing fixes
  ide: add ide_proc_register_port()
  ide: add "initializing" argument to ide_register_hw()
  ide: cable detection fixes (take 2)
  ide: move IDE settings handling to ide-proc.c
  ide: split off ioctl handling from IDE settings (v2)
  ide: make /proc/ide/ optional
  ide: add ide_tune_dma() helper
  ide: rework the code for selecting the best DMA transfer mode (v3)
  ide: fix UDMA/MWDMA/SWDMA masks (v3)

* git://git.linux-nfs.org/pub/linux/nfs-2.6:
  NFS: Kill the obsolete NFS_PARANOIA
  NFS: use __set_current_state()
  sunrpc: fix crash in rpc_malloc()
  NFS: Clean up NFSv4 XDR error message
  NFS: NFS client underestimates how large an NFSv4 SETATTR reply can be
  SUNRPC: Fix pointer arithmetic bug recently introduced in rpc_malloc/free
  NFS: Remove redundant check in nfs_check_verifier()
  NFS: Fix a jiffie wraparound issue

PIO should be restored also for ATAPI devices during resume, fix it.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

IDE PCI host drivers should register themselves with IDE core only when
IDE driver is built-in, otherwise (IDE driver is modular and thus IDE PCI
host drivers are also modular) the code has no effect and just complicates
the probing.

Fix it by adding new config option CONFIG_IDEPCI_PCIBUS (defined only when
needed and invisible to the user) and covering by #ifdef/#endif the code
in question.  It turned out that "ide=reverse" was silently accepted but did
nothing in case when IDE driver was modular, this is fixed now.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* create_proc_ide_interfaces() tries to add /proc entries for every probed
  and initialized IDE port, replace it by ide_proc_register_port() which does
  it only for the given port (also rename destroy_proc_ide_interface() to
  ide_proc_unregister_port() for consistency)
  
* convert {create,destroy}_proc_ide_interface[s]() users to use new functions

* pmac driver depended on proc_ide_create() to add /proc port entries, fix it
  
* au1xxx-ide, swarm and cs5520 drivers depended indirectly on ide-generic
  driver (CONFIG_IDE_GENERIC=y) to add port /proc entries, fix them

* there is now no need to add /proc entries for IDE ports in proc_ide_create()
  so don't do it

* proc_ide_create() needs now to be called before drivers are probed - fix it,
  while at it make proc_ide_create() create /proc "ide" directory
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add "initializing" argument to ide_register_hw() and use it instead of ide.c
wide variable of the same name.  Update all users of ide_register_hw()
accordingly.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Tejun's recent eighty_ninty_three() fix has inspired me to do more thorough
review of the cable detection code...

* print user-friendly warning about limiting the maximum transfer speed
  to UDMA33 (and the reason behind it) when 80-wire cable is not detected,
  also while at it cleanup eighty_ninty_three() a bit

* use eighty_ninty_three() in ide_ata66_check(), this actually fixes 3 bugs:
  - bit 14 (word 93 validity check) == 1 && bit 13 (80-wire cable test) == 1
    were used as 80-wire cable present test for CONFIG_IDEDMA_IVB=n case
    (please see FIXME comment in eighty_ninty_three() for more details)
  - CONFIG_IDEDMA_IVB=y/n cases were interchanged
  - check for SATA devices was missing

* remove private cable warnings from pdc_202xx{old,new} drivers now that core
  code provides this functionality (plus, in pdc202xx_new case the test could
  give false warnings for ATAPI devices because pdc202xx_new driver doesn't
  even support ATAPI DMA)

Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>