Be we read and chase pointers from the VBT, it is prudent to make sure
that those accesses are wholly contained within the MMIO region, or else
we may cause a kernel panic during boot.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: NShobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make sure that the whole BDB section is within the MMIO region prior to
accessing it contents. That we don't read outside of the secion is left
up to the individual section parsers.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: NShobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

At least on VLV but probably on other platforms too we depend on RC6
being enabled for RPM, so disable RPM until the delayed RC6 enabling
completes.

v2:
- explain the reason for the _noresume version of RPM get (Daniel)
- use the simpler 'if (schedule_work()) rpm_get();' instead of
  'if (!cancel_work_sync()) rpm_get(); schedule_work();'
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Getting struct_mutex around the whole intel_enable_gt_powersave()
function is not necessary, since it's only needed for the ILK path
therein.

This will make intel_enable_gt_powersave() useable on the RPM resume
path for >=GEN6 (added in an upcoming patch to reset the RPS state
during RPM resume), where we can't (and need not) get this mutex.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These debugfs entries access registers that need the D0 power state so
get an RPM ref for them.

v2:
- for all these entries we only need D0 state, so get only an RPM ref,
  not a power domain ref (Daniel, Paulo)
- the dpio entry is not an issue any more as it got removed (Ville)
- restore commit message from v1 (Paulo)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There are igt tools that can read/write the DPIO registers, so having a
debugfs entry for only some of those registers is somewhat arbitrary /
redundant. Remove it.

v2:
- instead of fixing the entry by taking a power domain reference around
  the register accesses, remove the entry (Ville)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The parsing was incorrect for ILK and VLV.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Not clearing this flag causes spurious interrupts at least in D3 state,
so before enabling RPM we need to fix this. We were already setting this
flag when enabling interrupts, only clearing it was missing.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These will be needed by the upcoming VLV RPM helpers.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The BDW GT3 has two independent BSD rings, which can be used to process the
video commands. To be simpler, it is transparent to user-space driver/middle.
Instead the kernel driver will decide which ring is to dispatch the BSD video
command.

As every BSD ring is powerful, it is enough to dispatch the BSD video command
based on the drm fd. In such case it can play back video stream while encoding
another video stream. The coarse ping-pong mechanism is used to determine
which BSD ring is used to dispatch the BSD video command.

V1->V2: Follow Daniel's comment and use the simple ping-pong mechanism.
This is only to add the support of dual BSD rings on BDW GT3 machine.
The further optimization will be considered in another patch set.

V2->V3: Follow Daniel's comment to use the struct_mutext instead of
atomic_t during determining which ring can be used to dispatch Video command.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The Gen7 doesn't have the second BSD ring. But it will complain the switch check
warning message during compilation. So just add it to remove the
switch check warning.

V1->V2: Follow Daniel's comment to update the comment
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Based on the hardware spec, the BDW GT3 machine has two independent
BSD ring that can be used to dispatch the video commands.
So just initialize it.

V3->V4: Follow Imre's comment to do some minor updates. For example:
more comments are added to describe the semaphore between ring.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
[danvet: Fix up checkpatch error.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Based on the hardware spec, the BDW GT3 has the different configuration
with the BDW GT1/GT2. So split the BDW device info definition.
This is to do the preparation for adding the Dual BSD rings on BDW GT3 machine.

V1->V2: Follow Daniel's comment to pay attention to the stolen check for BDW
in kernel/early-quirks.c
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to make sure that userspace keeps on following the contract,
otherwise we won't be able to use the reserved fields at all.

v2: Add DRM_DEBUG (Chris)

Testcase: igt/gem_exec_params/*-dirt
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A bit tricky since 0 is also a valid constant ...

v2: Add DRM_DEBUG (Chris)

Testcase: igt/gem_exec_params/rel-constants-*
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently we catch it, but silently succeed. Our userspace is
better than this.

v2: Add DRM_DEBUG (Chris)

Testcase: igt/gem_exec_params/sol-reset-*
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we include the expected values for the failing ring register checks,
it makes it marginally easier to see which is the culprit.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NOscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

During module load, if we fail to initialise the rings, we abort the
load reporting EIO. However during resume, even though we report EIO as
we fail to reinitialize the ringbuffers, the resume continues and the
device is restored - albeit in a non-functional state. As we cannot
execute any commands on the GPU, it is effectively wedged, mark it so.

As we now preserve the ringbuffers across resume, this should prevent
UXA from falling into the trap of repeatedly sending invalid
batchbuffers and dropping all further rendering into /dev/null.
Reported-and-tested-by: NJiri Kosina <jkosina@suse.cz>
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NOscar Mateo <oscar.mateo@intel.com>
[danvet: Drop unused error, spotted by Oscar.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Even without enabling the ringbuffers to allow command execution, we can
still control the display engines to enable modesetting. So make the
ringbuffer initialization failure soft, and mark the GPU as wedged
instead.

v2: Only treat an EIO from ring initialisation as a soft failure, and
abort module load for any other failure, such as allocation failures.

v3: Add an *ERROR* prior to declaring the GPU wedged so that it stands
out like a sore thumb in the logs
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NOscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Tearing down the ring buffers across resume is overkill, risks
unnecessary failure and increases fragmentation.

After failure, since the device is still active we may end up trying to
write into the dangling iomapping and trigger an oops.

v2: stop_ringbuffers() was meant to call stop(ring) not
cleanup(ring) during resume!
Reported-by: NJae-hyeon Park <jhyeon@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=72351
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NOscar Mateo <oscar.mateo@intel.com>
[danvet: s/ring->obj == NULL/!intel_ring_initialized(ring)/ as
suggested by Oscar.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For readibility and guess at the meaning behind the constants.

v2: Claim only the meagerest connections with reality.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NOscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I don't think this is necessary; at least it doesn't appear to be on my
BYT.  Dropping it speeds up our shutdown code a little, in some cases
resulting in faster init times.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Remove occurrences of unused struct qxl_device pointer in functions
qxl_ttm_fault() and qxl_init_mem_type().

Detected by Coverity: CID 1019128, CID 1019129.
Signed-off-by: NChristian Engelmayer <cengelma@gmx.at>
Signed-off-by: NDave Airlie <airlied@redhat.com>

For QXL hw we really want the bits to be replaced as we change
the preferred mode on the fly, and the same goes for virgl when
I get to it, however the original fix for this seems to have caused
a wierd regression on Intel G33 that in a stunning display of failure
at opposition to his normal self, Daniel failed to diagnose.

So we are left doing this, ugly ugly ugly ugly, Daniel you fixed
that G33 yet?, ugly, ugly.
Tested-by: NMarc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Use %pad for dma_addr_t, because a dma_addr_t type can vary
based on build options. So, it prevents possible build warnings
in printks.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Reviewed-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

devm_ioremap_resource() returns an error pointer, not NULL. Thus,
the result should be checked with IS_ERR().
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

exynos_drm_crtc_mode_set assigns primary framebuffer to plane without
taking reference. Then during framebuffer removal it is dereferenced twice,
causing oops. The patch fixes it.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

A number of older CMOTech modems are based on Qualcomm
chips.  The blacklisted interfaces are QMI/wwan.
Reported-by: NLars Melin <larsm17@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Device interface layout:
0: ff/ff/ff - serial
1: ff/00/00 - serial AT+PPP
2: ff/ff/ff - QMI/wwan
3: 08/06/50 - storage

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Device interface layout:
0: ff/ff/ff - serial
1: ff/ff/ff - serial AT+PPP
2: 08/06/50 - storage
3: ff/ff/ff - serial
4: ff/ff/ff - QMI/wwan

Cc: <stable@vger.kernel.org>
Reported-by: NJulio Araujo <julio.araujo@wllctel.com.br>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

During firmware download the device expects memory addresses in
big-endian byte order. As the wIndex parameter which hold the address is
sent in little-endian byte order regardless of host byte order, we need
to use swab16 rather than cpu_to_be16.

Also make sure to handle the struct ti_i2c_desc size parameter which is
returned in little-endian byte order.
Reported-by: NLudovic Drolez <ldrolez@debian.org>
Tested-by: NLudovic Drolez <ldrolez@debian.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When CONFIG_PCI and CONFIG_PM are not selected, xhci.c gets this
warning:
drivers/usb/host/xhci.c:409:13: warning: ‘xhci_msix_sync_irqs’ defined
but not used [-Wunused-function]

Instead of creating nested #ifdefs, this patch fixes it by defining the
xHCI PCI stubs as inline.

This warning has been in since 3.2 kernel and was
caused by commit 421aa841
"usb/xhci: hide MSI code behind PCI bars", but wasn't noticed
until 3.13 when a configuration with these options was tried
Signed-off-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Cc: stable@vger.kernel.org # 3.2
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

After suspend another Renesas PCI-X USB 3.0 card doesn't work.
[root@fedora-20 ~]# lspci -vmnnd 1912:
Device:	03:00.0
Class:	USB controller [0c03]
Vendor:	Renesas Technology Corp. [1912]
Device:	uPD720202 USB 3.0 Host Controller [0015]
SVendor:	Renesas Technology Corp. [1912]
SDevice:	uPD720202 USB 3.0 Host Controller [0015]
Rev:	02
ProgIf:	30

This patch should be applied to stable kernel 3.14 that contain
the commit 1aa9578c
"xhci: Fix resume issues on Renesas chips in Samsung laptops"
Reported-and-tested-by: NAnatoly Kharchenko <rfr-bugs@yandex.ru>
Reference: http://redmine.russianfedora.pro/issues/1315Signed-off-by: NIgor Gnatenko <i.gnatenko.brain@gmail.com>
Cc: stable@vger.kernel.org # 3.14
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The same issue like with Panther Point chipsets. If the USB ports are
switched to xHCI on shutdown, the xHCI host will send a spurious interrupt,
which will wake the system. Some BIOS have work around for this, but not all.
One example is Compulab's mini-desktop, the Intense-PC2.

The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.

This patch should be backported to stable kernels as old as 3.12,
that contain the commit 638298dc
"xhci: Fix spurious wakeups after S5 on Haswell"
Signed-off-by: NDenis Turischev <denis@compulab.co.il>
Cc: stable@vger.kernel.org
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>