dev->horkage should be cleared over device hotunplug/plug.  Clear it
in ata_dev_init().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJoseph Chan <josephchan@via.com.tw>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix "lost" interrupt problem when using dma with CD/DVD drives in some
configurations.  This problem can make installing linux from media
impossible for distro's that have switched to libata-only configurations.

The simple fix is to eliminate the use of dma for reading drive status, etc,
by checking the number of bytes to transferred.

This change will only affect the behavior of atapi devices, not disks.
There is more info at http://bugzilla.redhat.com/show_bug.cgi?id=242229
This patch is for 2.6.22.1
Signed-off-by: NJeff Norden <jnorden@math.tntech.edu>
Reviewed-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

via_do_set_mode overwrites 80-wire cable detection bits. Let's
preserve them.
Signed-off-by: NLaurent Riffard <laurent.riffard@free.fr>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Ocelot: remove remaining bits
  [MIPS] TLB: Fix instruction bitmasks
  [MIPS] R10000: Fix wrong test in dma-default.c
  [MIPS] Provide empty irq_enable_hazard definition for legacy and R1 cores.
  [MIPS] Sibyte: Remove broken dependency on EXPERIMENTAL from SIBYTE_SB1xxx_SOC.
  [MIPS] Kconfig: whitespace cleanup.
  [MIPS] PCI: Set need_domain_info if controller domain index is non-zero.
  [MIPS] BCM1480: Fix computation of interrupt mask address register.
  [MIPS] i8259: Add disable method.
  [MIPS] tty: add the new ioctls and definitions.

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c-algo-bit: Read block data bugfix
  i2c-pxa: Fix adapter number
  i2c-gpio: Fix adapter number

* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
  hwmon: End of I/O region off-by-one

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  [CRYPTO] blkcipher: Fix inverted test in blkcipher_get_spot
  [CRYPTO] blkcipher: Fix handling of kmalloc page straddling

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: fw-ohci: ignore failure of pci_set_power_state (fix suspend regression)

* 'for-linus' of git://www.linux-m32r.org/git/takata/linux-2.6_dev:
  m32r: Rename STI/CLI macros
  m32r: build fix of entry.S
  m32r: Separate syscall table from entry.S
  m32r: Cosmetic updates of arch/m32r/kernel/entry.S
  m32r: Exit ei_handler directly for no IRQ case or IPI operations
  m32r: Simplify ei_handler code
  m32r: Define symbols to unify platform-dependent ICU checks
  m32r: Move dot.gdbinit files
  m32r: Rearrange platform-dependent codes
  m32r: Add defconfig file for the usrv platform.
  m32r: Update defconfig files for 2.6.23-rc1
  m32r: Move defconfig files to arch/m32r/configs/

* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
  sched: fix ideal_runtime calculations for reniced tasks
  sched: improve prev_sum_exec_runtime setting
  sched: simplify __check_preempt_curr_fair()
  sched: fix xtensa build warning
  sched: debug: fix sum_exec_runtime clearing
  sched: debug: fix cfs_rq->wait_runtime accounting
  sched: fix niced_granularity() shift
  sched: fix MC/HT scheduler optimization, without breaking the FUZZ logic.

* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
  [XFS] fix nasty quota hashtable allocation bug
  [XFS] fix sparse shadowed variable warnings
  [XFS] fix ASSERT and ASSERT_ALWAYS
  [XFS] Fix sparse warning in kmem_shake_allow
  [XFS] Fix sparse NULL vs 0 warnings
  [XFS] Set filestreams object timeout to something sane.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
  [x86 setup] Work around bug in Xen HVM

Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-Off-By: NThiemo Seufer <ths@networkno.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NMaxime Bizon <mbizon@freebox.fr>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Following a strict interpretation the empty definition of irq_enable_hazard
has always been a bug - but an intentional one because it didn't bite.
This has now changed, for uniprocessor kernels mm/slab.c:do_drain()

[...]
        on_each_cpu(do_drain, cachep, 1, 1);
        check_irq_on();
[...]

may be compiled into a mtc0 c0_status; mfc0 c0_status sequence resulting
in a back-to-back hazard.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Otherwise Kconfig will produce a nonsenical .config for a kernel that is
neither 32-bit nor 64-bit.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This fixes this little funny:

bigsur:/proc/bus/pci# ls -l
total 0
dr-xr-xr-x    2 root     root            0 Aug 28 19:31 00
dr-xr-xr-x    2 root     root            0 Aug 28 19:31 00
dr-xr-xr-x    2 root     root            0 Aug 28 19:31 01
dr-xr-xr-x    2 root     root            0 Aug 28 19:31 03
-r--r--r--    1 root     root            0 Aug 28 19:31 devices
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

  CC      arch/mips/sibyte/bcm1480/irq.o
arch/mips/sibyte/bcm1480/irq.c: In function 'bcm1480_mask_irq':
arch/mips/sibyte/bcm1480/irq.c:112: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c:114: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c: In function 'bcm1480_unmask_irq':
arch/mips/sibyte/bcm1480/irq.c:130: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c:132: warning: cast to pointer from integer of different size
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

After 76d21601, the qemu NE2000 was
frequently producing WATCHDOG timeouts.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Same as all the others, just put in the constants for the existing kernel
code and termios2 structure
Signed-off-by: NAlan Cox <alan@redhat.com>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Previously, ibmebus derived a device's bus_id from its location code.
The location code is not guaranteed to be unique, so we might get bus_id
collisions if two devices share the same location code.  The OFDT
full_name, however, is unique, so we use that instead (truncating it
on the left if it is too long).
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

On PS3, A storage device may show up in the repository before the hypervisor
has finished probing:
  - If its type is not yet known, it shows up as PS3_DEV_TYPE_STOR_DUMMY,
  - If its regions are being probed, it shows up as having zero regions.
If any of these happen, consider the device not yet present.  The storage
probe thread will retry later.

This fixes the timing-dependent problem where a kernel booted from FLASH ROM
sometimes cannot find the hard disk.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

At present, running any SPE program on the ps3 will trigger a BUG_ON
when spufs_run_spu tries to clear the master run control bit, as lv1
does not make the master run control available to Linux.

This change makes SPE apps work again by disabling changes to the
master run control on PS3.  Although we don't have the facility to
disable a SPE with supervisor-level privileges, it's better than
hitting the BUG_ON unconditionally.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Acked-by: NMasato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The Cell BE Architecture spec states that the SPU MFC Class 0 interrupt
is edge-triggered.  The current spu interrupt handler assumes this
behavior and does not clear the interrupt status.

The PS3 hypervisor visualizes all SPU interrupts as level, and on return
from the interrupt handler the hypervisor will deliver a new virtual
interrupt for any unmasked interrupts which for which the status has not
been cleared.  This fix clears the interrupt status in the interrupt
handler.
Signed-off-by: NMasato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Acked-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The previous patch had the conditional inverted.  This patch fixes it
so that we return the original position if it does not straddle a page.

Thanks to Bob Gilligan for spotting this.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This fixes a bug in the way i2c-algo-bit handles I2C_M_RECV_LEN,
used to implement i2c_smbus_read_block_data().  Previously, in the
absence of PEC (rarely used!) it would NAK the "length" byte:

	S addr Rd [A] [length] NA

That prevents the subsequent data bytes from being read:

	S addr Rd [A] [length] { A [data] }* NA

The primary fix just reorders two code blocks, so the length used
in the "should I NAK now?" check incorporates the data which it
just read from the slave device.

However, that move also highlighted other fault handling glitches.
This fixes those by abstracting the RX path ack/nak logic, so it
can be used in more than one location.  Also, a few CodingStyle
issues were also resolved.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

It turns out that platform_device.id is a "u32" so testing it for being
nonnegative is useless when setting up an i2c adapte.  Instead,
do what the platform_bus code does and test it against the value "-1".
Signed-off-by: NJean Delvare <khali@linux-fr.org>

It turns out that platform_device.id is a "u32" so testing it for being
nonnegative is useless when setting up an i2c bitbang device.  Instead,
do what the platform_bus code does and test it against the value "-1". 
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Fix an off-by-one error in the I/O region declaration of two
hardware monitoring drivers (lm78 and w83781d.) We were requesting
one extra port at the end of the region.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

The function blkcipher_get_spot tries to return a buffer of
the specified length that does not straddle a page.  It has
an off-by-one bug so it may advance a page unnecessarily.

What's worse, one of its callers doesn't provide a buffer
that's sufficiently long for this operation.

This patch fixes both problems.  Thanks to Bob Gilligan for
diagnosing this problem and providing a fix.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Fixes (papers over) "Sleep problems with kernels >= 2.6.21 on powerpc",
http://lkml.org/lkml/2007/8/25/155.  The issue is that the FireWire
controller's pci_dev.current_state of iBook G3 and presumably older
PowerBooks is still in PCI_UNKNOWN instead of PCI_D0 when the firewire
driver's .suspend method is called.

Like it was suggested earlier in http://lkml.org/lkml/2006/10/24/13, we
do not fail .suspend anymore if pci_set_power_state failed.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The names of STI and CLI macros were derived from i386 arch historically,
but their name are incomprehensible.
So, for easy to understand, rename these macros to ENABLE_INTERRUPTS
and DISABLE_INTERRUPTS, respectively.
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>

This patch fixes the following compile error:
<--  snip  -->
 ...
  AS      arch/m32r/kernel/entry.o
/home/bunk/linux/kernel-2.6/linux-2.6.23-rc3-mm1/arch/m32r/kernel/entry.S: Assembler messages:
/home/bunk/linux/kernel-2.6/linux-2.6.23-rc3-mm1/arch/m32r/kernel/entry.S:358: Error: bad instruction `addi r0,#(((((0)+(64))+(32))+(32)))'
make[2]: *** [arch/m32r/kernel/entry.o] Error 1
<--  snip  -->
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>
Cc: Adrian Bunk <bunk@kernel.org>

fix ideal_runtime:

  - do not scale it using niced_granularity()
    it is against sum_exec_delta, so its wall-time, not fair-time.

  - move the whole check into __check_preempt_curr_fair()
    so that wakeup preemption can also benefit from the new logic.

this also results in code size reduction:

   text    data     bss     dec     hex filename
  13391     228    1204   14823    39e7 sched.o.before
  13369     228    1204   14801    39d1 sched.o.after
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Second preparatory patch for fix-ideal runtime:

Mark prev_sum_exec_runtime at the beginning of our run, the same spot
that adds our wait period to wait_runtime. This seems a more natural
location to do this, and it also reduces the code a bit:

   text    data     bss     dec     hex filename
  13397     228    1204   14829    39ed sched.o.before
  13391     228    1204   14823    39e7 sched.o.after
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Preparatory patch for fix-ideal-runtime:

simplify __check_preempt_curr_fair(): get rid of the integer return.

   text    data     bss     dec     hex filename
  13404     228    1204   14836    39f4 sched.o.before
  13393     228    1204   14825    39e9 sched.o.after

functionality is unchanged.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

rename RSR to SRR - 'RSR' is already defined on xtensa.

found by Adrian Bunk.
Signed-off-by: NIngo Molnar <mingo@elte.hu>