This is useless and introduces a dependency between rfkill
and stop_device - the op_mode can't call stop_device from
the rfkill notification since it would lead to an endless
recursion.
Next patches will need to do so.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Under very specific circumstances, the firmware might
ignore a host command. This was debugged and we ended up
seeing that the power management hardware was faulty.
In order to workaround this issue, we keep the NIC awake
as long as we have host commands in flight. This will avoid
to put the hardware into buggy condition.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In case of invalid section_id, the function returns after
it aleready allocated memory. Fixed by change the order of actions.
Signed-off-by: NEytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The AC / fifo mapping was wrong - BE packets landed in VO
FIFO. The iwl_mvm_tx_fifo enumeration isn't in the same
order as ieee80211_ac_numbers enumeration.
Since the firmware relies on fifo / ac mapping - this led
to wrong behavior. E.g. the firmware sends beacon with the
same QoS parameters as VO, and it actually took the
parameters of BK. There are probably more severe issues.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This lock was never acquired in the primary interrupt
handler, but since it was acquired along with irq_lock
which had to disable interrupts, rxq->lock had to disable
interrupts too.
Now that trans_pcie->irq_lock isn't acquired in the primary
interrupt handler, rxq->lock can let interrupt enabled.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since we don't take this lock in the primary interrupt
handler, there is no pointin disabling the interrupt
in the critical section protected by trans_pcie->irq_lock.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Handling interrupt with no cause and printing logs doesn't
need to be ICT / non-ICT specific move this to the common
code.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This was useful when the handling was not in the same
context as the interrupt cause retrieval: we could have
several hard interrupts until the handler gets called.
Since we retrieve the interrupt cause in the handler itself,
there is no need to OR the interrupt causes.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

These functions are meant to return an interrupt cause and
not an irqreturn_t.
We still return IRQ_HANDLED if we had an error and IRQ_NONE
if our device hasn't fired any interrupt.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of having:
iwl_pcie_irq_handler
	iwl_pcie_isr_ict
		iwl_pcie_isr_non_ict

we now have:

iwl_pcie_irq_handler:
	if (use_ict))
		iwl_pcie_int_cause_ict;
	else
		iwl_pcie_int_cause_non_ict;

This is much clearer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We now disable the interrupts in the hardware from the
upper half and all the rest (including reading the interrupt
cause) is done in the handler.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The purpose of this is to be able to call these functions
from the interrupt handler and not from the primary
interrupt handler.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Separate the code that simply disables interrupt in the
hardware and the code that checks what interrupt fired.
This will be useful to move the second part in the threaded
handler which will be done in a future patch.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Track the interrupt mask in software, making it exactly
what is configured in the interrupt mask register in the
hardware.
This allows not to access the register from the interrupt
handler. This was the case for ICT interrupt already, but
not for non-ICT interrupt.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since iwl_trans_pcie_alloc_ict is called in the PCIe
allocation code, we always set CSR_INT_BIT_RX_PERIODIC.
Move that bit to the default list of interrupts we enable
and simplify the code.
Also use dma_zalloc_ and avoid to memset the memory
afterwards.
trans_pcie->ict_index is 0 since trans_pcie has just been
kzalloced, remove the redundant assignment.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NEyalX Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

RTS protection was turned on once aggregation was enabled but it
was never turned off. Remove turning on RTS protection in the LQ command
completely as TX_CMD_FLG_PROT_REQUIRE gets set in iwl_mvm_set_tx_cmd
for every Tx which is part of an aggregation. This would already cause
RTS protection to be used during aggregations.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Set the Tx/Rx highest long GI rates in the VHT Supported MCS Set
field according to the chip capabilties.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

MCS9 introduces some corner cases in the current rs
algorithm which may lead to non optimal throughput and
instability in the throughput. Until all the corner
cases are resolved disable MCS9 for Tx as a workaround
which yields better throughput results as MCS8 is much
more stable.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Fix a regression introduced in "iwlwifi: mvm: fix ht protection flags"
where an AP/IBSS MAC context could have been updated even before the
context was added to the FW. This fix avoids the following warning:

WARNING: ... at .../drivers/net/wireless/iwlwifi/mvm/mac-ctxt.c:1132
    iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm]()
Changing inactive MAC 0c:8b:fd:01:1a:30/3
Modules linked in: [...]
Call Trace:
[<c16041fd>] dump_stack+0x41/0x52
[<c1041074>] warn_slowpath_common+0x84/0xa0
[<f80d8f45>] ? iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm]
[<f80d8f45>] ? iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm]
[<c1041133>] warn_slowpath_fmt+0x33/0x40
[<f80d8f45>] iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm]
[<f80d517a>] iwl_mvm_bss_info_changed+0x22a/0x4b0 [iwlmvm]
[<c160831d>] ? mutex_unlock+0xd/0x10
[<f80d4678>] ? iwl_mvm_configure_filter+0x58/0x70 [iwlmvm]
[<f80d4f50>] ? iwl_mvm_mac_tx+0xc0/0xc0 [iwlmvm]
[<f8132d83>] ieee80211_bss_info_change_notify+0xa3/0x1d0 [mac80211]
[<f8149247>] ? ieee80211_del_virtual_monitor+0x127/0x1f0 [mac80211]
[<f8149cac>] ieee80211_do_open+0x12c/0xeb0 [mac80211]
[<c106c6de>] ? __raw_notifier_call_chain+0x1e/0x30
[<c106c70f>] ? raw_notifier_call_chain+0x1f/0x30
[<f814aa8d>] ieee80211_open+0x5d/0x60 [mac80211]
[<c1500c7b>] __dev_open+0xab/0x140
[<c160b39a>] ? _raw_spin_unlock_bh+0x2a/0x30
[<c1500f41>] __dev_change_flags+0x81/0x160
[<c10ab6fc>] ? __lock_is_held+0x3c/0x60
[<c15010d1>] dev_change_flags+0x21/0x60
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reported-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

debufs.o appeared twice in the Makefile. Fix that.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Extract the scale action decision to a different function
in preparation of modifying it. While at it also convert
the scale action values from hardcoded values to a clear enum.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The logs are emitted in a flow in which there were retries
and the rates in the rate table entry didn't match the active
or search table. This doesn't indicate a problem and is
expected in most cases where there will be retries for some
reason. Remove the logs.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The new logic will attempt more rates with less retries
per rate. Also when starting off with MIMO it will
fallback to SISO with the same MCS and only then to Legacy.
Previously we fell back directly to Legacy.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The supported legacy rate mask is initialized when rs
is initialized based on the remote peer supported rates.
There's no need to re mask it repeatedly with the supported
remote peer rates.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Simplify the code a bit more by extracting the rates table
building logic into a separate function and handle setting
a fixed rate for debug in a separate flow.
Also avoid using and saving ucode rate format in different
places. Instead use rs_rate struct and convert to ucode format
only when filling the rates table in the LQ command.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Current firmware doesn't handle well uAPSD in P2P Client.
When it will be fixed, the firmware will set a TLV flag to notify
the driver that uAPSD is supported in P2P client mode.
Check this flag when sending power command for P2P client.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

It is not currently implemented for SDIO, and not required for other slave
buses as well.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Clear the FW_ERROR status before the common start_fw transport code.
Remove the transport specific clears.

After these patches the FW_ERROR flag is only set and cleared by common
transport code.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In case a sync command timeouts or Tx is stuck while a FW error
interrupt arrives, we might call iwl_op_mode_nic_error twice before
a restart has been initiated. This will cause a reprobe. Unify calls
to this function at the transport level and only call it on the first
FW error in a given by checking the transport FW error flag.

While at it, remove the privately defined iwl_nic_error from PCIE code
and use the common callback instead.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

iwl_nvm_init() return value wasn't checked in some
path, which resulted in the following panic (if
there was some issue with the nvm):

Unable to handle kernel NULL pointer dereference at virtual address 00000004
pgd = d0460000
[00000004] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP
Modules linked in: iwlmvm(+) iwlwifi mac80211 cfg80211 compat [last unloaded: compat]
PC is at iwl_mvm_mac_setup_register+0x12c/0x460 [iwlmvm]
LR is at 0x2710
pc : [<bf50dd4c>]    lr : [<00002710>]    psr: 20800013
sp : d00cfe18  ip : 0000081e  fp : d006b908
r10: d0711408  r9 : bf532e64  r8 : d006b5bc
r7 : d01af000  r6 : bf39cefc  r5 : d006ab00  r4 : d006b5a4
r3 : 00000001  r2 : 00000000  r1 : d006a120  r0 : d006b860
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This pointer was not used anywhere.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Move rs_program_fix_rate right before it's caller where we're
already in the context of an ifdef CPTCFG_MAC80211_DEBUGFS so
we can get rid of the extra ifdefs surrounding the original
location.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Stop Tx and commands from arriving to the transport layer when a FW
error has occurred. A HW recovery should take place before. Remove
transport specific checks of the same nature (note that not all
transports were protected).
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The same bits are employed in all transport layers. Put the status
field in the common transport layer. This allows us to employ them
in common transport code.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The stop_hw trans callback is not well defined. It is missing in many
cleanup flows and the division of labor between stop_device/stop_hw
is cumbersome. Remove stop_hw and use stop_device to perform both.
Implement this for all current transports.

PCIE needs some extra configuration the op-mode is leaving to configure
RF kill. Expose this explicitly as a new op_mode_leave trans callback.
Take the call to stop_device outside iwl_run_mvm_init_ucode, this
makes more sense and WARN when we want to run the INIT firmware while
it has run already.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The documentation for smps_requests is unclear, rewrite it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Configure the phy context to the minimum required
bandwidth, given by ctx->min_def.

Tuning to a narrower bandwidth should reduce the
noise level and consume less power.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Configure the fw to filter multicast according to
the addresses given by mac80211.

Note that bssid should be given even if we want
to pass all the multicast frames.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is more related to phy contexts than to mac context.
Move this function to there.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>