mac80211 is in charge of determining the basic rates,
so we are not using the RATE_BASIC flag anymore.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change improves the maintainability of these drivers. No functionality
is changed.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Initial mesh support: add Mesh Point to supported interfaces mask and allow
hwsim to send beacons in mesh mode.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Based on a patch from Shailendra Govardhan <shailen@marvell.com>.
This patch allows implementation of more specific wake-on-lan rules than those
of ethtool.

Please note that only firmware 5.110.22.p20 and above supports this feature.

This patch only implements the driver/firmware interface, not the
userspace/driver interface.
Signed-off-by: NAnna Neal <anna@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Otherwise some configs can result in missing print_ssid...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
   netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.

OK, becasue Dave S. Miller said, "every direct netdev->priv usage is a bug",
and I want to kill netdev->priv later, I decided to convert all the direct
reference of netdev->priv first.

(Original patch posted by Wang Chen <wangchen@cn.fujitsu.com> w/ above
changelog but using dev->ml_priv.  That doesn't seem appropriate
to me for this driver, so I've revamped it to use netdev_priv()
instead. -- JWL)
Reviewed-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for SFP+ PHY in the following device ID's (10DB,
10F1, 10E1).  These SFP+ PHY's are accessed via an I2C interface so the
patch also includes functions to support this.

Another feature of note is that the PHY is pluggable and some
rearchitecting was needed to support this.
Signed-off-by: NDonald Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds an interface to configure the Backward Congestion Notification
(BCN) feature.  In a BCN capabale network, congestion notifications
from congested points out in the network can cause the end station
limit the rate of a given traffic flow.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds a netlink interface for Data Center Bridging (DCB) to get and set
the enable state of the Priority Flow Control (PFC) feature.
Primarily, this is a way to turn off PFC in the driver while DCB
remains enabled.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds interface for Data Center Bridging (DCB) to query (and set if
supported) the number of traffic classes currently supported by the
device for the two (DCB) features: priority groups (PG) and priority
flow control (PFC).
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds to the netlink interface for Data Center Bridging (DCB), allowing
the DCB capabilities supported by a device to be queried.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for Data Center Bridging (DCB) features in the ixgbe
driver and adds an rtnetlink interface for configuring DCB to the
kernel.  The DCB feature support included are Priority Grouping (PG) -
which allows bandwidth guarantees to be allocated to groups to traffic
based on the 802.1q priority, and Priority Based Flow Control (PFC) -
which introduces a new MAC control PAUSE frame which works at
granularity of the 802.1p priority instead of the link (IEEE 802.3x).
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert the HIPPI infrastructure for use with net_device_ops.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert this driver to net_device_ops.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to ethernet. Convert infrastructure and the one lone FDDI
driver (for the one lone user of that hardware??). Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert to new network device ops interface.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.

Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Make device driver to allocate memory for netdev.
2. Convert all directly reference of netdev->priv to netdev_priv().
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to kill directly reference of netdev->priv too.
Because the private data needs special memory: lower 16MB DMA.
alloc_etherdev() can not do this work.
So we can't use netdev->priv to point to netdev's private data.
Use netdev->ml_priv instead.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Use netdev_priv(dev) to replace dev->priv.
2. Alloc netdev's private data by alloc_netdev().
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LAN9500 supports tx checksum offload, which slightly decreases cpu
utilisation.  The benefit isn't very large because we still require
the skb to be linearized, but it does save a few cycles.

This patch adds support for it, and enables it by default.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the device is suspended with the cable disconnected, then
resumed with the cable connected, dev->open is called before
resume. During resume, we request an IRQ, but the IRQ was
already assigned during dev->open, resulting in the warning
shown below.

Don't request an IRQ if the device is running.

Call Trace:
 [<c011b89a>] warn_on_slowpath+0x40/0x59
 [<c023df15>] raw_pci_read+0x4d/0x55
 [<c023dff3>] pci_read+0x1c/0x21
 [<c01bcd81>] __pci_find_next_cap_ttl+0x44/0x70
 [<c01bce86>] __pci_find_next_cap+0x1a/0x1f
 [<c01bcef9>] pci_find_capability+0x28/0x2c
 [<c01c4144>] pci_msi_check_device+0x53/0x62
 [<c01c49c2>] pci_enable_msi+0x3a/0x1cd
 [<e019f17b>] atl2_write_phy_reg+0x40/0x5f [atl2]
 [<c01061b1>] dma_generic_alloc_coherent+0x0/0xd7
 [<e019f107>] atl2_request_irq+0x15/0x49 [atl2]
 [<e01a1481>] atl2_open+0x20b/0x297 [atl2]
 [<c024a35c>] dev_open+0x62/0x91
 [<c0248b9a>] dev_change_flags+0x93/0x141
 [<c024f308>] do_setlink+0x238/0x2d5
 [<c02501b2>] rtnl_setlink+0xa9/0xbf
 [<c0297f0c>] mutex_lock+0xb/0x19
 [<c024ffa7>] rtnl_dump_ifinfo+0x0/0x69
 [<c0250109>] rtnl_setlink+0x0/0xbf
 [<c024fe42>] rtnetlink_rcv_msg+0x185/0x19f
 [<c0240fd1>] sock_rmalloc+0x23/0x57
 [<c024fcbd>] rtnetlink_rcv_msg+0x0/0x19f
 [<c0259457>] netlink_rcv_skb+0x2d/0x71
 [<c024fcb7>] rtnetlink_rcv+0x14/0x1a
 [<c025929e>] netlink_unicast+0x184/0x1e4
 [<c025992a>] netlink_sendmsg+0x233/0x240
 [<c023f405>] sock_sendmsg+0xb7/0xd0
 [<c0129131>] autoremove_wake_function+0x0/0x2b
 [<c0129131>] autoremove_wake_function+0x0/0x2b
 [<c0147796>] mempool_alloc+0x2d/0x9e
 [<c020c923>] scsi_pool_alloc_command+0x35/0x4f
 [<c0297f0c>] mutex_lock+0xb/0x19
 [<c028e867>] unix_stream_recvmsg+0x357/0x3e2
 [<c01b81c9>] copy_from_user+0x23/0x4f
 [<c02452ea>] verify_iovec+0x3e/0x6c
 [<c023f5ab>] sys_sendmsg+0x18d/0x1f0
 [<c023ffa8>] sys_recvmsg+0x146/0x1c8
 [<c0240016>] sys_recvmsg+0x1b4/0x1c8
 [<c0118f48>] __wake_up+0xf/0x15
 [<c02586cd>] netlink_table_ungrab+0x17/0x19
 [<c01b83ba>] copy_to_user+0x25/0x3b
 [<c023fe4a>] move_addr_to_user+0x50/0x68
 [<c0240266>] sys_getsockname+0x6f/0x9a
 [<c0240280>] sys_getsockname+0x89/0x9a
 [<c015046a>] do_wp_page+0x3ae/0x41a
 [<c0151525>] handle_mm_fault+0x4c5/0x540
 [<c02405d0>] sys_socketcall+0x176/0x1b0
 [<c010376d>] sysenter_do_call+0x12/0x21
Signed-off-by: NAlan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: NJay Cliburn <jcliburn@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Randy Dunlap found that SFC_MTD was selected when sfc was built-in and
the MTD core was a module.  Don't allow that combination.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to kill directly reference of netdev->priv too.
Because the private data should be allocated in DMA area, alloc_etherdev()
can't satisfy this needs.
Use netdev->ml_priv to point to lance_private.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, if multiple unicast addresses are programmed into a
mv643xx_eth interface, the core networking will resort to enabling
promiscuous mode on the interface, as mv643xx_eth does not implement
->set_rx_mode().

This patch switches mv643xx_eth over from ->set_multicast_list()
to ->set_rx_mode(), and implements support for secondary unicast
addresses.  The hardware can handle multiple unicast addresses as
long as their first 11 nibbles are the same (i.e. are of the form
xx:xx:xx:xx:xx:xy where the x part is the same for all addresses), so
if that is the case, we use that mode.  If it's not the case, we enable
unicast promiscuous mode in the hardware, which is slightly better than
enabling promiscuous mode for multicasts as well, which is what would
happen before.

While we are at it, change the programming sequence so that we
don't clear all filter bits first, so we don't lose all incoming
packets while the filter is being reprogrammed.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since txq_alloc_desc_index() is a very simple function, and since
descriptor ring index handling for transmit reclaim, receive
processing and receive refill is already handled inline as well,
inline txq_alloc_desc_index() into its two call sites.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv643xx_eth driver uses the rdl()/wrl() macros to read and
write hardware registers.  Per-port registers are accessed in the
following way:

	#define PORT_STATUS(p)			(0x0444 + ((p) << 10))

	[...]

	static inline u32 rdl(struct mv643xx_eth_private *mp, int offset)
	{
		return readl(mp->shared->base + offset);
	}

	[...]

	port_status = rdl(mp, PORT_STATUS(mp->port_num));

By giving the per-port 'struct mv643xx_eth_private' its own
'void __iomem *base' pointer that points to the per-port register
area, we can get rid of both the double indirection and the << 10
that is done for every per-port register access -- this patch does
that.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix up a couple of coding style issues caught by checkpatch.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVernon Sauder <VernonInHand@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removes the use of a hardcoded sram_size, determine string_spec
location from the MCP header instead.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Properly attribute transmit and receive drops by incrementing the
per-slice counter.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add AX_MEDIUM_ENCK also when speed = 10/100Mbps. This allows my belkin
f5d5055 to work with my 100Mbps switch and with an old 10Mbps ISA card.
Without this patch, the card is recognized and the interface is brought
up fine, but no packets actually flow through the interface.
Signed-off-by: NPantelis Koukousoulas <pktoss@gmail.com>
Acked-by: NDavid Hollis <dhollis@davehollis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When mv643xx_eth allocates skbuffs, it adds
'dma_get_cache_alignment() - 1' to the length it needs, so that it can
align the skb's ->data pointer to a cache boundary.  When checking
whether a transmitted skbuff can be reused as a receive buffer, these
bytes needs to be included into the minimum bound for the recycle check.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update to change of mii_bus interface and fix some warning.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since all the memory, which pointed by netdev->priv, are allocated in
advance instead of by alloc_netdev().  Use netdev->ml_priv to point to
those memory.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>