In the xmit path, the driver may drop some pkts due to reasons such as
DMA mapping errors, out of memory conditions or to protect HW from
unrecoverable errors. Add a counter in TX-stats for such drops.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current EQ delay calculation for AIC is based only on RX packet rate.
This fails to be effective when there's only TX and no RX.
This patch inclues:
- Calculating EQ-delay based on both RX and TX pps.
- Modifying EQ-delay of all EQs via one cmd, instead of issuing a separate
  cmd for each EQ.
- A new structure to store interrupt coalescing parameters, in a separate
  cache-line from the EQ-obj.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This cmd needs to be sent to FW when enabling VFs (currently used only
for Lancer.) Also, avoid calling the cmd when driver loads and finds that
VFs are already enabled from a previous load.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On BE3-R 1G ports (identified by port numbers 2 and 3) the FW cannot properly
support multiple TXQs. This also makes the number of RX and TX queues symmetric
as only a single RXQ is available on 1G ports.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is a required field for all TX_CREATE cmd versions > 0.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Re-define the sriov_want() macro to check for number of VFs that need
to be enabled in the current load of the driver or the number of VFs that
still remain enabled from the previous load (attached VFs cannot be disabled.)
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VLAN priority is not being displayed for a VF currently when user executes
"ip link show" command. This patch fixes it.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thix fix allows the VLAN priority to be configured for a VF interface
via the "ip link set DEVICE vf NUM" path.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now the VF interfaces have privilege to add VLANs.
Allow VLANs to be configured on these interfaces.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In BE3-R, when UMC is enabled, the number of VLANs that can be added
to the interface is reduced to 15.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the interface runs out of the allocated entries in VLAN table,
we program the interface in VLAN promiscuous mode.
Use OPCODE_COMMON_NTWK_RX_FILTER to set VLAN Promiscuous mode
instead of OPCODE_COMMON_NTWK_VLAN_CONFIG.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Size of be_nic_res_desc structure is incorrect. Fix it.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tx on SH-R can lockup if the packet size is less than 32 bytes.
Pad such packets to a safer 36-byte size.
Patch uses the Lancer-R workaround - which checks for packet <= 32-bytes
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are a mix of function prototypes with and without extern
in the kernel sources.  Standardize on not using extern for
function prototypes.

Function prototypes don't need to be written with extern.
extern is assumed by the compiler.  Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAntonio Alecrim Jr <antonio.alecrim@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SkyHawk-R can support VEB or VEPA mode.
This patch will allow the user to set/query this switch setting.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__GFP_ZERO is an uncommon flag and perhaps is better
not used.  static inline dma_zalloc_coherent exists
so convert the uses of dma_alloc_coherent with __GFP_ZERO
to the more common kernel style with zalloc.

Remove memset from the static inline dma_zalloc_coherent
and add just one use of __GFP_ZERO instead.

Trivially reduces the size of the existing uses of
dma_zalloc_coherent.

Realign arguments as appropriate.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support is provided only for combined channels. When SR-IOV is not
enabled, BE3 supports upto 16 channels and Lancer-R/SH-R support upto
32 channels.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) Move be_cmd_if_create() above queue create routines to allow
   TXQ creation (that requires if_handle) to be clubbed with TX-CQ creation.
2) Consolidate all queue create routines into be_setup_queues()
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the IF_CREATE FW cmd is issued only *after* MCCQ is created as
it was coded to only use MCCQ. By fixing this, cmd_if_create() can be
called before MCCQ is created and the same routine for VF provisioning
can be called after.
This allows for consolidating all the queue create routines by moving
the be_cmd_if_create() call above all queue create calls in be_setup().
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) use be_resources{} struct to query/store HW resource limits
2) The HW queue/resource limits for BE2/BE3 chips are mostly called out
   in driver as constants.  Code to handle this is scattered across various
   places in be_setup(). Consolidate this code into BEx_get_resources().
   For Lancer-R, Skyhawk-R, these limits are queried from FW.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) Parse PCIe descriptor for max-VFs supported by HW
2) Cleanup NIC descriptor parsing in get_func/profile_config() routines
3) Use common struct definitions for v0 and v1 versions of GET_FUNC_CONFIG
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

EQ_CREATEv2 explicitly returns the msix-index associated with a EQ.
For SH-R this is needed if EQs need to be deleted and re-created without
resetting a function.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In suspend-resume sequence, the OS could attempt to initialize the controller
before it is ready, check for POST state before going ahead.
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit fba87559 ("disable TX in be_close()") disabled TX in be_close()
to protect be_xmit() from touching freed up queues in the AER recovery
flow.  But, TX must be disabled *before* cleaning up TX completions in
the close() path, not after. This allows be_tx_compl_clean() to free up
all TX-req skbs that were notified to the HW.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible for some versions of firmware to advertise capabilities that driver
is not ready to handle. This may lead to controller stall. Since the driver is
interested only in subset of flags, clearing the rest.
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Uninitialized value was being returned in the non-failure case.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Log the event type for unknown async events
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BE2 FW GET_PHY_DETAILS cmd does not return fixed speeds supported.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For SH-R and Lancer-R, use the FW supported values for Max unicast MACs,
Max VLANs and Max multicast MACs.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a chip wide value and the PFs already report it.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new speeds are supported by variants of the Skyhawk-R chip.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These local functions are used only in this file.
Fix the following sparse warnings:

drivers/net/ethernet/emulex/benet/be_main.c:475:6: warning: symbol 'populate_erx_stats' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:1485:6: warning: symbol 'be_rx_compl_process_gro' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:2262:5: warning: symbol 'be_poll' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:3223:6: warning: symbol 'flash_cookie' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:3280:27: warning: symbol 'get_fsec_info' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:1013:5: warning: symbol 'be_cmd_mccq_ext_create' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:1071:5: warning: symbol 'be_cmd_mccq_org_create' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:3166:5: warning: symbol 'be_cmd_get_profile_config_mbox' was not declared. Should it be
static?
drivers/net/ethernet/emulex/benet/be_cmds.c:3194:5: warning: symbol 'be_cmd_get_profile_config_mccq' was not declared. Should it be
static?
drivers/net/ethernet/emulex/benet/be_roce.c:96:6: warning: symbol '_be_roce_dev_remove' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_roce.c:113:6: warning: symbol '_be_roce_dev_open' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_roce.c:129:6: warning: symbol '_be_roce_dev_close' was not declared. Should it be static?
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver uses dev_err when enabling of AER fails (e.g. PCIe AER is not
supported). The dev_info is more appropriate to avoid console pollution.

Cc: sathya.perla@emulex.com
Cc: subbu.seetharaman@emulex.com
Cc: ajit.khaparde@emulex.com
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the UC-list is being deleted from the HW MAC table, but the primary
MAC is not.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On SH-R and Lancer-R, GET_MAC_LIST cmd is better supported
(instead of NTWK_MAC_QUERY cmd) to query provisioned MAC addresses.
Similiarly, (on SH-R and Lancer-R) SET_MAC_LIST must be used by the PF to
provision a permanent MAC addresses to the VF.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code to configure the permanent MAC in be_setup() has become quite
complicated, with different FW cmds being used for BEx, SH-R and Lancer.
Simplify the logic by moving some of this complexity to be_cmds.c. This
makes the code in be_setup() a little more readable.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For BE3 VFs, the permanent MAC is added by its PF. The VF can retrieve its
pmac_id only via the IFACE_CREATE cmd. This is not true for Lancer and SH-R
VFs which get the pmac_id by issuing a ADD_IFACE_MAC cmd. So, use this
hack only for BE3 VFs.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the current design VFs were not allowed to program MAC/VLAN filters.
Only the PF driver was allowed to configure/provision MAC and transparent
VLANs to a VF. Change this to support MAC/VLAN filtering on a VF by a VM.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>