Driver needs to stop participating in firmware based Inter Driver
Communication (IDC) while unloading driver
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register for firmware based Inter Driver Communication (IDC) using initialize
NIC as the first mailbox command
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit d0e2c55e (veth: avoid a NULL deref in veth_stats_one)
added another NULL deref in veth_dellink().

# ip link add name veth1 type veth peer name veth0
# rmmod veth

We crash because veth_dellink() is called twice, so we must
take care of NULL peer.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was preventing GRO and RxCheckSum offload to happen.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some multicast addresses are common to all macvlans,
so if a multicast message has a hash value collision, we
have to deliver a copy to all macvlans, adding significant
latency and possible packet drops if netdev_max_backlog
limit is hit.

Having a per macvlan hash function permits to reduce the
impact of hash collisions.
Suggested-by: NMaciej Żenczykowski <maze@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NMaciej Żenczykowski <maze@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit cd431e73 (macvlan: add multicast filter) forgot
the broadcast case.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NMaciej Żenczykowski <maze@google.com>
SIgned-off-by: NMaciej Żenczykowski <maze@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc failures already get standardized OOM
messages and a dump_stack.

For the affected mallocs around these OOM messages:

Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The last (bool) parameter in bgmac_cmdcfg_maskset says if the write
should be made, even if value didn't change. Currently driver doesn't
match the specs about (not) forcing some changes. This makes it follow
them.
Reported-by: NNathan Hintz <nlhintz@hotmail.com>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds check for a valid Ethernet MAC address and in case it is not,
it will generate a valid random one, such that the adapter is still
usable.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have conflicting type qualifiers for "freg_t" in s390's ptrace.h and the
iphase atm device driver, which causes the compile error below.
Unfortunately the s390 typedef can't be renamed, since it's a user visible api,
nor can I change the include order in s390 code to avoid the conflict.

So simply rename the iphase typedef to a new name. Fixes this compile error:

In file included from drivers/atm/iphase.c:66:0:
drivers/atm/iphase.h:639:25: error: conflicting type qualifiers for 'freg_t'
In file included from next/arch/s390/include/asm/ptrace.h:9:0,
                 from next/arch/s390/include/asm/lowcore.h:12,
                 from next/arch/s390/include/asm/thread_info.h:30,
                 from include/linux/thread_info.h:54,
                 from include/linux/preempt.h:9,
                 from include/linux/spinlock.h:50,
                 from include/linux/seqlock.h:29,
                 from include/linux/time.h:5,
                 from include/linux/stat.h:18,
                 from include/linux/module.h:10,
                 from drivers/atm/iphase.c:43:
next/arch/s390/include/uapi/asm/ptrace.h:197:3: note: previous declaration of 'freg_t' was here
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Nchas williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BCM4785 or sometimes named BMC4705 is a Broadcom SoC which a
Gigabit 5750 Ethernet core. The core is connected via PCI with the rest
of the SoC, but it uses some extension.

This core does not use a firmware or an eeprom.

Some devices only have a switch which supports 100MBit/s, this
currently does not work with this driver.

This patch was original written by Michael Buesch <m@bues.ch> and is in
OpenWrt for some years now.

This was tested on a Linksys WRT610N V1 and older versions of this patch
were tested by other people on different devices.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In OpenWrt we currently use a switch driver which uses the ioctls to
configure the switch in the phy. We have to provide the phy_id to do
so, but without this patch this is not possible.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

=========================================================
[ INFO: possible irq lock inversion dependency detected ]
3.8.0-rc5+ #82 Not tainted
---------------------------------------------------------
swapper/0/0 just changed the state of lock:
 (&(&fep->hw_lock)->rlock){..-...}, at: [<8034e2f8>] fec_enet_start_xmit+0x48/0x                      2cc
but this lock took another, SOFTIRQ-unsafe lock in the past:
(prepare_lock){+.+.+.}

and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:

CPU0				CPU1
----				----
lock(prepare_lock);
				local_irq_disable()
				lock(&(&fep->hw_lock)->rlock);
				lock(prepare_lock);
<Interrupt>
lock(&(&fep->hw_lock)->rlock);

*** DEADLOCK ***
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Old method will cause init spinlock twice.
New method will avoid init spinlock twice and fix miss init spinlock
at fec_restart.

BUG: spinlock bad magic on CPU#1, swapper/0/1
lock: 0xbfae0f8c, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
Backtrace:
 [<80011d54>] (dump_backtrace+0x0/0x10c) from [<804e7800>] (dump_stack+0x18/0x1c)
 r6:bfae0000 r5:bfae0f8c r4:00000000 r3:806c1310
 [<804e77e8>] (dump_stack+0x0/0x1c) from [<804e9f20>] (spin_dump+0x80/0x94)
 [<804e9ea0>] (spin_dump+0x0/0x94) from [<804e9f60>] (spin_bug+0x2c/0x30)
 r5:805f6f8c r4:bfae0f8c
 [<804e9f34>] (spin_bug+0x0/0x30) from [<80257984>] (do_raw_spin_lock+0x170/0x1b0                                         )
 r5:806b4950 r4:bfae0f8c
 [<80257814>] (do_raw_spin_lock+0x0/0x1b0) from [<804ed15c>] (_raw_spin_lock_irqs                                         ave+0x18/0x20)
 [<804ed144>] (_raw_spin_lock_irqsave+0x0/0x20) from [<8033c694>] (fec_ptp_start_                                         cyclecounter+0x3c/0x120)
 r4:bfae0f8c r3:00000002
 [<8033c658>] (fec_ptp_start_cyclecounter+0x0/0x120) from [<80339e08>] (fec_resta                                         rt+0x56c/0x5f8)
 r8:00000000 r7:806e6f48 r6:00000112 r5:806b4950 r4:bfae0000
 [<8033989c>] (fec_restart+0x0/0x5f8) from [<8033b9e4>] (fec_probe+0x508/0xa48)
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix issue in Mellanox driver related to BQL.  netdev_tx_reset_queue
was not being called in certain situations where the device was
being start and stopped.  Moved netdev_tx_reset_queue from the reset
device path to mlx4_en_free_tx_buf which is where the rings are
cleaned in a reset (specifically from device being stopped).
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-By: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Acked-by: NJan Beulich <JBeulich@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMatthew Daley <mattjd@gmail.com>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Acked-by: NJan Beulich <JBeulich@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A buggy or malicious frontend should not be able to confuse netback.
If we spot anything which is not as it should be then shutdown the
device and don't try to continue with the ring in a potentially
hostile state. Well behaved and non-hostile frontends will not be
penalised.

As well as making the existing checks for such errors fatal also add a
new check that ensures that there isn't an insane number of requests
on the ring (i.e. more than would fit in the ring). If the ring
contains garbage then previously is was possible to loop over this
insane number, getting an error each time and therefore not generating
any more pending requests and therefore not exiting the loop in
xen_netbk_tx_build_gops for an externded period.

Also turn various netdev_dbg calls which no precipitate a fatal error
into netdev_err, they are rate limited because the device is shutdown
afterwards.

This fixes at least one known DoS/softlockup of the backend domain.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: NJan Beulich <JBeulich@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for setting embedded switch fdb in case of SRIOV, by
implementing ndo_fdb_{add, del, dump}. This will allow to use
bridged configuration with multi-function. In order to add VM MAC
to the eSwitch fdb, the following command may be used over the relevant function interface:
bridge fdb add <MAC> permanent self dev <IFACE>
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement and advertise unicast MAC filtering, such that setting macvlan
instance over mlx4_en interfaces will not require the networking core
to put mlx4_en devices in promiscuous mode.

If for some reason adding a unicast address filter fails e.g as of missing space in
the HW mac table, the device forces itself into promiscuous mode (and out of this
forced state when enough space is available).
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As a preparation step for supporting multiple unicast addresses, store MAC addresses in hash table.
Remove the radix tree for MAC addresses per QP, as it's not in use.
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to having more than one unicast MAC per port, we need to keep track
of the previous MAC address in the flow of ndo_set_mac_address,
so that mlx4_en_replace_mac will know what to replace.
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, mlx4_en_do_set_multicast serves as the ndo_set_rx_mode entry for mlx4_en,
doing all related work. Split it to few calls, one per required functionality
(e.g multicast, promiscuous, etc) and rename some structures and calls
to use rx_mode notation instead of multicast.
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move low level code that deals with management of Ethernet MACs and QPs from mlx4_core to mlx4_en.
Also convert the new functions to deal with MACs in form of char array instead of u64.

Actual functions moved:
mlx4_replace_mac
mlx4_get_eth_qp
mlx4_put_eth_qp

To conduct this change, some functionality had to be exported from the core,
the following functions were added:
mlx4_get_base_qp
__mlx4_replace_mac (low level function for CX1/A0 compatibility)
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the code consistent in regard to error messages
not spanning multiple lines.
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, RX path code that does RX filtering is not optimized
and does an expensive conversion. In order to use ether_addr_equal_64bits
which is optimized for such cases, we need the MAC address kept by the device
to be in the form of unsigned char array instead of u64. Store the MAC address
as unsigned char array and convert to/from u64 out of the fast path when needed.
Side effect of this is that we no longer need priv->mac, since it's the same
as dev->dev_addr.

This optimization was suggested by Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently there are relatively complex conditional checks in the fast path,
for TX loopback enabling and resulting RX filter logic.
Move elaborate if's out of data path, replace them with a single flag
for each state and update that state from appropriate places.
Also, in native (non SRIOV) mode and not in loopback or in selftest,
there is no need to try and filter out packets that HW loopback-ed,
as in native mode we do not loopback packets anymore.
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes up

commit e8e89622
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Tue Dec 18 22:25:11 2012 +0100

    drm/ttm: fix fence locking in ttm_buffer_object_transfer

which leaves behind a might_sleep in atomic context, since the
fence_lock spinlock is held over a kmalloc(GFP_KERNEL) call. The fix
is to revert the above commit and only take the lock where we need it,
around the call to ->sync_obj_ref.

v2: Fixup things noticed by Maarten Lankhorst:
- Brown paper bag locking bug.
- No need for kzalloc if we clear the entire thing on the next line.
- check for bo->sync_obj (totally unlikely race, but still someone
  else could have snuck in) and clear fbo->sync_obj if it's cleared
  already.
Reported-by: NDave Airlie <airlied@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Don't access uninitialized work-queue when removing device.
The work queue is initialized only if the device multi-queue.
So don't call cancel_work unless this is a multi-queue device.

This fixes the following panic:

Kernel panic - not syncing: BUG!
Call Trace:
62031b28:  [<6026085d>] panic+0x16b/0x2d3
62031b30:  [<6004ef5e>] flush_work+0x0/0x1d7
62031b60:  [<602606f2>] panic+0x0/0x2d3
62031b68:  [<600333b0>] memcpy+0x0/0x140
62031b80:  [<6002d58a>] unblock_signals+0x0/0x84
62031ba0:  [<602609c5>] printk+0x0/0xa0
62031bd8:  [<60264e51>] __mutex_unlock_slowpath+0x13d/0x148
62031c10:  [<6004ef5e>] flush_work+0x0/0x1d7
62031c18:  [<60050234>] try_to_grab_pending+0x0/0x17e
62031c38:  [<6004e984>] get_work_gcwq+0x71/0x8f
62031c48:  [<60050539>] __cancel_work_timer+0x5b/0x115
62031c78:  [<628acc85>] unplug_port+0x0/0x191 [virtio_console]
62031c98:  [<6005061c>] cancel_work_sync+0x12/0x14
62031ca8:  [<628ace96>] virtcons_remove+0x80/0x15c [virtio_console]
62031ce8:  [<628191de>] virtio_dev_remove+0x1e/0x7e [virtio]
62031d08:  [<601cf242>] __device_release_driver+0x75/0xe4
62031d28:  [<601cf2dd>] device_release_driver+0x2c/0x40
62031d48:  [<601ce0dd>] driver_unbind+0x7d/0xc6
62031d88:  [<601cd5d9>] drv_attr_store+0x27/0x29
62031d98:  [<60115f61>] sysfs_write_file+0x100/0x14d
62031df8:  [<600b737d>] vfs_write+0xcb/0x184
62031e08:  [<600b58b8>] filp_close+0x88/0x94
62031e38:  [<600b7686>] sys_write+0x59/0x88
62031e88:  [<6001ced1>] handle_syscall+0x5d/0x80
62031ea8:  [<60030a74>] userspace+0x405/0x531
62031f08:  [<600d32cc>] sys_dup+0x0/0x5e
62031f28:  [<601b11d6>] strcpy+0x0/0x18
62031f38:  [<600be46c>] do_execve+0x10/0x12
62031f48:  [<600184c7>] run_init_process+0x43/0x45
62031fd8:  [<60019a91>] new_thread_handler+0xba/0xbc
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Cc: stable@kernel.org
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Adding new class/subclass/protocol combinations based on the GPLed
out-of-tree Huawei driver. One of these has already appeared on a
device labelled as "E320".
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding a new vendor specific class/subclass/protocol combination
for CDC NCM devices based on information from a GPLed out-of-tree
driver from Huawei.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When changing the device from or to promisc mode this only affects the
device after the device is bought up the next time. For bridging it is
needed to change the device to promisc mode while it is up, which is
possible with this patch.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The generic implementation just changes the netdev struct and does not
write the new mac address to the hardware or issues some command to do
so.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting up IPv6 addresses on configurations with many macvlans
is not really working, as many multicast messages are dropped.

Add a multicast filter to macvlan to reduce the amount of cloned
skbs and overhead.

Successfully tested with 1024 macvlans on one ethernet device.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some modes don't require any special carrier handling so
in these cases, the kernel can control the carrier as for
any other interface.  However, some other modes, e.g. lacp,
requires more than just that, so userspace needs to control
the carrier itself.

The daemon today is ready to control it, but the kernel
still can change it based on events.

This fix so that either kernel or userspace is controlling
the carrier.
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

adding support for VLAN interface for cpsw.

CPSW VLAN Capability
* Can filter VLAN packets in Hardware
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add helper functions for VLAN ALE implementations for Add, Delete
Dump VLAN related ALE entries
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>