When a root port receives the same errors more than once before the
kernel process them, the Multiple Error Messages Received flags are set
by hardware. Because the root port could only save one kind of
correctable error source id and another uncorrectable error source id at
the same time, the second message sender id is lost if the 2 messages
are sent from 2 different devices. This patch makes the kernel search
all devices under the root port when multiple messages are received.
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NZhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

When the bus id part of error source id is equal to 0 or nosourceid=1,
make the kernel probe the AER status registers of all devices under the
root port to find the initial error reporter.
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NZhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Based on PCI Express AER specs, a root port might receive multiple
TLP errors while it could only save a correctable error source id
and an uncorrectable error source id at the same time. In addition,
some root port hardware might be unable to provide a correct source
id, i.e., the source id, or the bus id part of the source id provided
by root port might be equal to 0.

The patchset implements the support in kernel by searching the device
tree under the root port.

Patch 1 changes parameter cb of function pci_walk_bus to return a value.
When cb return non-zero, pci_walk_bus stops more searching on the
device tree.
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NZhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The "owner" field in struct hotplug_slot_ops is initialized by PCI
hotplug core. So each hotplug controller driver doesn't need to
initialize it.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Create symbolic link to hotplug driver module in the PCI slot
directory (/sys/bus/pci/slots/<SLOT#>). In the past, we need to load
hotplug drivers one by one to identify the hotplug driver that handles
the slot, and it was very inconvenient especially for trouble shooting.
With this change, we can easily identify the hotplug driver.
Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Current has_foo() functions in pci_hotplug_core.c returns 0 if the
"foo" property is true. It would cause misunderstanding. In addition,
the error code of those functions is never checked, so this patch
changes those functions' error code to 'bool' and return true if the
property "foo" is true.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The EMI support in pciehp is obviously broken. It is implemented using
struct hotplug_slot_attribute, but sysfs_ops for pci_slot_ktype is NOT
for struct hotplug_slot_attribute, but for struct pci_slot_attribute.
This bug had been there for a long time, maybe it was introduced when
PCI slot framework was introduced. The reason why this bug didn't
cause any problem is maybe the EMI support is not tested at all
because of lack of test environment.

As described above, the EMI support in pciehp seems not to be tested
at all. So this patch removes EMI support from pciehp, instead of
fixing the bug.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Describe check_enable_amd_mmconf.
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch adds a minimal HOWTO for PCIE AER software error injection
in Documentation/PCI/pcieaer-howto.txt.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This is used by PCIE AER error injection to fake an PCI AER interrupt.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

pci_bus_set_ops changes pci_ops associated with a pci_bus. This can be
used by debug tools such as PCIE AER error injection to fake some PCI
configuration registers.
Acked-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Use pci_is_root_bus() in pci_common_swizzle() for checking if the pci
bus is root, for code consistency.
Reviewed-by: NAlex Chiang <achiang@hp.com>
Reviewed-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Use pci_is_root_bus() in pci_get_interrupt_pin() for checking if the
pci bus is root, for code consistency.
Reviewed-by: NAlex Chiang <achiang@hp.com>
Reviewed-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Use pci_is_root_bus() in pci_read_bridge_bases() to check if the pci
bus is root, for code consistency.
Reviewed-by: NAlex Chiang <achiang@hp.com>
Reviewed-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Use pci_is_root_bus() in pci_find_upstream_pcie_bridge() to check if
the pci bus is root, for code consistency.
Reviewed-by: NAlex Chiang <achiang@hp.com>
Reviewed-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Use pci_is_root_bus() in acpi_find_root_bridge_handle() to check if
the pci bus is root, for code consistency.
Reviewed-by: NAlex Chiang <achiang@hp.com>
Reviewed-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Use pci_is_root_bus() in acpi_pci_get_bridge_handle() to check if the
pci bus is root, for code consistency.
Reviewed-by: NGrant Grundler <grundler@parisc-linux.org>
Reviewed-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

I found no references to SMBus in ACPI DSDT disassembly on my laptop
so this should be safe.
Signed-off-by: NMichal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Some BIOSes hide 'overflow' device (dev #6) for i82875P/PE chipsets.
The same happens for i82865P/PE. Add a quirk to enable this device.
This allows i82875 EDAC driver to bind to chipset's dev #6 and not
dev #0 as the latter is used by AGP driver.

On my laptop (i82865P based) ACPI code is disabling this device
again in \_SB.PCI0._CRS method (called at least at PNP init time).
This can be easily worked around by patching DSDT.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NMichal Miroslaw <mirq-linux@rere.qmqm.pl>
Acked-by: NDoug Thompson <norsk5@yahoo.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Addition of one unknown subsystem identifier to the quirks handler for
chipset i82855GM_HB on notebook Asus A6L. This exposes the otherwise
hidden SMBus controller within the south bridge ICH4-M.
Signed-off-by: NMats Erik Andersson <mats.andersson@gisladisker.se>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Adds support for PCI Express transaction layer end-to-end CRC checking
(ECRC).  This patch will enable/disable ECRC checking by setting/clearing
the ECRC Check Enable and/or ECRC Generation Enable bits for devices that
support ECRC.

The ECRC setting is controlled by the "pci=ecrc=<policy>" command-line
option. If this option is not set or is set to 'bios", the enable and
generation bits are left in whatever state that firmware/BIOS set them to.
The "off" setting turns them off, and the "on" option turns them on (if the
device supports it).

Turning ECRC on or off can be a data integrity versus performance
tradeoff.  In theory, turning it on will catch more data errors, turning
it off means possibly better performance since CRC does not need to be
calculated by the PCIe hardware and packet sizes are reduced.
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

According to the PCI PM specification (PCI Bus Power Management
Interface Specification, Rev. 1.2, Section 5.4.1) we are supposed to
reinitialize devices that have PCI_PM_CTRL_NO_SOFT_RESET clear during
all transitions from PCI_D3hot to PCI_D0, but we only do it if the
device's current_state field is equal to PCI_UNKNOWN.

This may lead to problems if a device with PCI_PM_CTRL_NO_SOFT_RESET
unset is put into PCI_D3hot at run time by its driver and
pci_set_power_state() is used to put it back into PCI_D0, because in
that case the device will remain uninitialized after
pci_set_power_state() has returned.  Prevent that from happening by
modifying pci_raw_set_power_state() to reinitialize devices with
PCI_PM_CTRL_NO_SOFT_RESET unset during all transitions from D3 to D0.

Cc: stable@kernel.org
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

PCIe root complex integrated endpoint does not implement ARI, so this
kind of endpoint uses 3-bit function number. The function dependency
link of the integrated endpoint should be calculated using the device
number plus the value from function dependency link register.

Normal endpoint always implements ARI and the function dependency link
register contains 8-bit function number (i.e. `devfn' from software's
perspective).
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

We always call pci_stop_bus_device before calling pci_destroy_dev.

Since pci_stop_bus_device calls pci_stop_dev, there is no need
for pci_destroy_dev to repeat the call.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

pci_enable_msix currently returns -EINVAL if you ask
for more vectors than supported by the device, which would
typically cause fallback to regular interrupts.

It's better to return the table size, making the driver retry
MSI-X with less vectors.
Reviewed-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

VIA has a strange chipset, it has root port under a bridge. Disable ASPM
for such strange chipset.

Cc: stable@kernel.org
Tested-by: NWolfgang Denk <wd@denx.de>
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

At this point, it seems to solve more problems than it causes, so let's try using it by default.  It's an easy revert if it ends up causing trouble.
Reviewed-by: NYinghai Lu <yhlu.kernel@gmail.com>
Acked-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The last in-tree caller of pci_find_slot has been converted, so
let's get rid of this deprecated interface.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Convert uses of pci_find_slot to modern API.

In the conversion sites, we end up calling pci_dev_put() right away.

This may seem like it misses the entire point of doing something like
pci_get_bus_and_slot(), since we drop the reference so soon, but it turns
out we don't actually do much with the returned pci_dev.

I plan on untangling cpqphp further, but clearly cpqphp never worried too
much about a properly refcounted pci_dev anyway. For now, this conversion
seems reasonable, as it gets rid of the last in-tree caller of pci_find_slot.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Eliminate this warning:
	warning: return discards qualifiers from pointer target type
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

I have no clue what the original intent here was, but the code as
written is useless.

The old dbg() statement above the old callsite might lead one to think
that at one point, there was supposed to be some recursion, but any
sense of sanity here has been lost to the ravages of time.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Instead of making multiple calls to pcibios_get_irq_routing_table, let's
just do it once and save the answer.

The reason we were making multiple calls is because we liked to calculate
its length and perform some loop over it. Instead of open-coding the length
calculation every time, provide it in an inline helper function.

Finally, since pci_print_IRQ_route() is used only for debug, let's only
do it when cpqhp_debug is set.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Handle an empty slot at the top of the loop, and continue early.

This allows us to un-indent the rest of the function by one level.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Clean up style, whitespace in cpqphp_pci.c
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Check for an empty slot, and return early if so.

This allows us to un-indent the rest of the function by one level.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Style and whitespace cleanups, no functional change.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Apply DeMorgan's theorem:

	if ((pdev->revision > 2) || (vendor_id == PCI_VENDOR_ID_INTEL))

turns into

	if ((pdev->revision <= 2) && (vendor_id != PCI_VENDOR_ID_INTEL))

Now we can bail out early from the function if the controller is not
supported.

This allows us to un-indent the remainder of the function quite a bit and
make it much more readable.

Fix up some extra braces, and un-indent the 'case' labels in the switch
statement as per CodingStyle.

No functional change.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Clean up style and eliminate superfluous braces and parens.

No functional change.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Impact: refactor

Refactor code to follow convention more closely and eliminate the need
for some useless prototypes.

No functional change.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Clean up cpqphp.h to follow 80 column convention.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>